Install Instructions

ManualsBrandsHoneywell ManualsDampers1" Sweat Linear Flow Valve (6.6 Cv)

INSTALLATION INSTRUCTIONS

Put Bar Code Here

95C-10920-03

VC2, VC4, VC60, VC8

ON-OFF ACTUATOR FOR VC SERIES BALANCED

HYDRONIC VALVES

These 2-position (open/close) control actuators are used with

VCZ1000, 1100, 6000 and 6100 series hydronic valves in a

normal indoor environment to provide quick opening/closing to

control the flow of hot and/or chilled water or glycol solution to

60% concentration. They are designed for on-off "zone"

control of heating/cooling systems, or to control individual fan

coil, baseboard radiator or convector applications.

Depending on the model selected, the actuator can be

controlled by a low or line voltage SPST or SPDT controller,

such as a room thermostat, aquastat or flow switch.

VC80 series valve actuators are designed to be used with

hard-wired electronic thermostats with series anticipator or

power-stealing thermostats. Recommended control

thermostats include T8601D, T8401C,T8380 and T8360

families.

VC actuators use cam-operated cartridge travel to resist water

hammer. Internal limit switches prevent motor overrun.

SPECIFICATIONS

The specifications following are nominal and conform to

generally acceptable industry standards. Honeywell is not

responsible for damages resulting from misapplication or

misuse of its products

Supply Voltage: Colour coded label

24V, 50Hz Model Blue

24V, 60Hz Model Blue

100-130V, 50-60Hz Model Black

200-240V, 50-60Hz Model Red

Power consumption: 6 Watts Max. at nominal Voltage (dur-

ing valve position change). Use 24 V Class 2 transformer

and provide 6 VA for transformer and connection wire siz-

ing.

Maximum Duty Cycle: 15%

Nominal timing:

Valve opens in 6 seconds @ 60Hz (20% longer @ 50Hz).

VC8040 Series opens in 12 seconds @ 60Hz (20% longer @

50Hz).

Electrical termination: 3 versions available:

(1) Molex™ (header # 39-30-1060). Requires mating connec-

tor (receptacle/housing # 39-01-2060). OR

(2) With integral 1 meter [nominal 39"] leadwire cable. OR

(3) With 5 feet (1.5 meter) plenum-rated leadwire cable per

UL94-5V. Includes plastic adapter for use with 3/8” flexible

conduit.

End Switch Rating:

2.2 A inductive from 5 to 110 Vac,

1.0 A inductive above 110 to 277 Vac.

Min. DC switching capability: 5mA @ 24 Vdc.

Operating ambient temperature: 0 to 65°C [32 to 150°F]

Except VC2114, VC2714, VC8114 & VC8714 are 0 to 60°C

[32 to 140°F]

Humidity Rating: 5-95% RH (non-condensing)

Fluid temperatures: 1 to 95° C [34 to 203° F]

Shipping & storage temperature: -40 to +65°C [-40 to

+150°F]

Atmosphere:

Non-corrosive, non-explosive.

Nominal Dimensions (Actuator Only):

3-23/32" width x 2-11/16" depth x 2-3/4" height

94 mm width x 68 mm depth x 70 mm height

Accessories: 272866B Valve Flushing Cap

Models:

Actuator Only: VC2, VC4, VC60, VC8 (See Table 1)

Bodies (Order Separately): VCZ... (See 95C-10919)

Summary of content (8 pages)

PAGE 1
VC2, VC4, VC60, VC8 ON-OFF ACTUATOR FOR VC SERIES BALANCED HYDRONIC VALVES INSTALLATION INSTRUCTIONS Power consumption: 6 Watts Max. at nominal Voltage (during valve position change). Use 24 V Class 2 transformer and provide 6 VA for transformer and connection wire sizing. Maximum Duty Cycle: 15% Nominal timing: Valve opens in 6 seconds @ 60Hz (20% longer @ 50Hz). VC8040 Series opens in 12 seconds @ 60Hz (20% longer @ 50Hz).
PAGE 2
VC2, VC4, VC60, VC8 Table 1. Actuator Model Identifiers Model No. Power Control Input Auxiliary Switch Table 2. VC Valve assembled dimensions Special Features Dimension C D VC2010zz00 24V~50Hz SPDT — Molex™ [4] Pipe Fitting Sizes VC2011zz00 24V~50Hz SPDT — Cable 1/2” BSPP (int.) [2] VC2012zz00 [1] 24V~50Hz SPDT — Molex™ 1/2” BSPT (int.) VC2611zz00 24V~50Hz SPDT Yes Cable 3/4” BSPP (int.) VC4012zz00 200-240V~ 50-60Hz SPST — Molex™ 3/4” BSPT (int.
PAGE 3
VC2, VC4, VC60, VC8 INSTALLATION Put the VC actuator manual lever in the manual open or the fully open (down) position to allow initial system flushing with the actuator mounted. This may be done without electrical hook-up. Alternatively, reusable flush caps, part # 272866B, may be purchased separately for use in initial flushing of dirty hydronic systems. When Installing This Product... 1. 2. 3. 4. 5. 6. Read these instructions carefully.
PAGE 4
VC2, VC4, VC60, VC8 Fig. 6. Wire Configuration for Molex™ Models for SPDT Controller (Series 40 & 80) Fig. 3. Flexible Conduit Attachment WIRING NOTE: Each 3-wire (SPDT) actuator must have individual SPDT controllers. Use series 40 or 80 for single controller to control multiple valves. Figures 4, 5, 6, & 7 wiring connections. Port “A” open and closed denote valve open and closed positions respectively.
PAGE 5
VC2, VC4, VC60, VC8 CHECKOUT 1. 2. 3. 4. Fig. 8. Actuator wiring for SPDT controller (Series 20 and 60). Raise the set point of the thermostat above room temperature to initiate a call for heat. Red valve position lever should move downward to the open position. For auxiliary switch models, observe all control devices. The valve should open and the auxiliary switch (if present) should close and make at the end of the opening stroke to activate auxiliary equipment.
PAGE 6
VC2, VC4, VC60, VC8 95C-10920—03 6
PAGE 7
VC2, VC4, VC60, VC8 7 95C-10920—03
PAGE 8
VC2, VC4, VC60, VC8 Automation and Control Solutions Honeywell International Inc. 1985 Douglas Drive North Golden Valley, MN 55422 customer.honeywell.com ® U.S. Registered Trademark © 2011 Honeywell International Inc. 95C-10920—03 T.D. Rev. 01-11 Printed in U.S.A.