WLAN Wasser- und Frostmelder Schnellstartanleitung 325307_A.
1 Herunterladen der Lyric-App Suchen Sie im App Store oder bei Google Play nach „Honeywell Lyric“. GET IT ON Wenn Sie die App heruntergeladen Lyric haben, starten Sie diese, registrieren Sie sich (falls erforderlich) und wechseln Sie dann zu „Menü“ und anschließend zu „Neues Gerät hinzufügen“. 2 Batterien einlegen Der Detektor wird über 3 AA-Batterien betrieben (im Lieferumfang enthalten). Öffnen Sie die Batterieabdeckung am Detektor und legen Sie die Batterien ein.
Verbinden Koppeln des Detektors und Vergeben eines Namens 1 Wählen Sie unter „Neues Gerät hinzufügen“ die Option „Lyric WLAN Wasser- und Frostmelder“ aus. Hinweis: Auf Ihrem Mobilgerät muss Bluetooth aktiviert sein. 2 Geben Sie einen Standort für Ihren Detektor an. Klicken Sie auf „WEITER“. 3 Der Detektor wird jetzt mit der App gekoppelt. Hinweis: Wenn Sie mehrere Detektoren einsetzen möchten, müssen Sie diese separat koppeln. 4 Ein akustisches Signal ertönt, und die LED des Detektors leuchtet blau.
Herstellen einer WLANVerbindung 1 Wählen Sie Ihr Netzwerk aus der Liste aus. Klicken Sie auf „WEITER“. 2 Geben Sie ggf. Ihr WLANKennwort ein. Klicken Sie auf „WEITER“. 3 Wenn die WLAN-Verbindung hergestellt ist, leuchtet die LED 5 Minuten lang grün. Anschließend erlischt sie, um die Batterie zu schonen. Hinweis: Nach einem Wechsel der Batterien wird die Verbindung mit Ihrem WLAN-Netzwerk automatisch wiederhergestellt.
Aufstellen Sensoren MontagePlatzieren Sie den WLAN öffnung Wasser- und Frostmelder mit der Unterseite flach auf dem Boden oder auf der zu überwachenden Oberfläche. KabelsensorFür die Wandmontage des buchse Detektors verwenden Sie die im Lieferumfang enthaltene SensorSchraube und den Dübel buchsenkappe und hängen Sie den Detektor an der Montageöffnung der Abdeckung auf.
Häufige Anwendungsmöglichkeiten Betrieb Verwenden der Lyric-App Im Folgenden sehen Sie einige Beispiele für Bildschirme der Lyric-App, die Ihnen beim Verwenden des WLAN Wasser- und Frostmelder angezeigt werden. Vom Gerät erkannte Leckagen 325307_A.
Zurücksetzen Zum Zurücksetzen führen Sie das Ende einer Büroklammer in die Reset-Öffnung ein. Üben Sie damit 5 Sekunden lang etwas Druck aus, um das WLAN und die Detektoreinstellungen zurückzusetzen und die Bluetooth-Kopplung neu zu starten. Die LED blinkt in diesem Fall blau. Zum Zurücksetzen des Sensors auf Werkseinstellungen führen Sie das Ende einer Büroklammer in die Reset-Öffnung ein. Üben Sie damit 15 Sekunden lang etwas Druck aus. Die LED blinkt zur Bestätigung blau.
Bei einem Alarm Wenn Wasser detektiert wurde, dauert es unter Umständen bis zu 1 Minute, bis der Detektor einen Alarm ausgibt und den Benutzer über das Leck benachrichtigt. Sie können den Detektor stummschalten, indem Sie die StummTaste in der App betätigen oder die Batterien oder den Kabelsensor vom Detektor entfernen. Es dauert unter Umständen bis zu 1 Minute, bis der Befehl zum Stummschalten den Detektor erreicht.