Smoke Alarm User's Manual

ManualsBrandsHoneywell ManualsSmoke AlarmXL 800 SERIES

XL 800 Series

FOR SMOKE CONTROL

HONEYWELL EXCEL 5000 OPEN SYSTEM

INSTALLATION AND COMMISSIONING INSTRUCTIONS

CONTENTS

General ............................................................................... 3

Before Installation ............................................................. 3

Installation ......................................................................... 3

Wiring ................................................................................. 4

XL800 Series Power Consumption ................................ 5

I/O Modules ................................................................... 5

Description of the XCL8010AU Controller Module ......... 7

Overview........................................................................ 7

Interfaces and Bus Connections .................................. 10

Technical Data............................................................. 10

System Data........................................................... 10

Operational Environment ....................................... 10

Smoke Control Configuration....................................... 10

Data File Set-Up .......................................................... 11

Panel Reset ................................................................. 11

Typical Power Limited Circuit for XL800 ...................... 11

Connecting Single Bus Controller Systems ................. 11

XCL8010AU, I/O Modules on Single Rail............... 12

Multiple Rails in Single Cabinet.............................. 12

LonWorks Bus I/O Modules in Separate Rooms .... 12

How to Connect Panel Bus and LONWORKS Bus Mixed

Controller Systems ...................................................... 12

Connecting I/O Modules......................................... 12

Connecting I/O Modules to the XCL8010AU.......... 12

Setting Address of Panel Bus I/O Modules .................. 13

Setting the I/O Bus Switch ........................................... 14

LONWORKS Bus Topologies.......................................... 14

C-Bus Topologies ........................................................ 14

Mounting/Dismounting Modules.................................... 14

Mounting/Dismounting Controller/Sockets ................... 15

Mounting Sockets................................................... 15

Connecting Sockets ............................................... 15

Dismounting Sockets ............................................. 16

Mounting/Dismounting Electronic Modules .................. 16

Mounting Electronic Modules ................................. 16

Dismounting Electronic Modules ............................ 17

Connecting via C-Bus .................................................. 17

Connecting to the Controller................................... 17

Setting the C-Bus Termination Switch.................... 17

Shielding ................................................................ 17

Connecting HMIs or Laptops........................................ 17

Connecting the XI582 Operator Interface ............... 17

Connecting Laptops (XL-Online/CARE) ................. 18

XCL8010AU Terminals........................................... 18

Features....................................................................... 18

LONWORKS Interface and Terminals ....................... 18

LONWORKS Service LED and Button....................... 18

C-Bus Tx LED and Rx LED .................................... 19

Reset Button........................................................... 19

HMI Interface.......................................................... 19

Alarm and Power LEDs .......................................... 20

Watchdog Status .................................................... 20

Modem Interface..................................................... 20

I/O Bus Switch S2................................................... 20

C-Bus Termination Switch S1................................. 21

Memory .................................................................. 21

Description of the I/O Modules ....................................... 21

Common Features ....................................................... 21

Analog Input Modules .................................................. 22

Types of Analog Input Modules .............................. 22

Features ................................................................. 22

Terminals................................................................ 22

XFL821AU Connection Examples .......................... 23

Analog Output Modules................................................ 24

Types of Analog Output Modules ........................... 24

Features ................................................................. 24

Terminals................................................................ 24

Technical Data........................................................ 24

Modules with Manual Overrides ............................. 25

XFL822AU Connection Example ............................ 25

Synchronization Behavior of Analog Output Module

Configured as Floating Output................................ 25

Binary Input Modules ................................................... 26

Types of Binary Input Modules ............................... 26

Features ................................................................. 26

Terminals................................................................ 26

Technical Data........................................................ 26

Status LEDs............................................................ 27

XF823AU Connection Examples ............................ 27

Relay Output Modules.................................................. 28

Types of Relay Output Modules ............................. 28

Features ................................................................. 28

Terminals................................................................ 28

Permissible Loads .................................................. 29

Status LEDs with Manual Overrides ....................... 29

Connection Examples............................................. 30

Summary of content (36 pages)

PAGE 1
XL 800 Series FOR SMOKE CONTROL HONEYWELL EXCEL 5000 OPEN SYSTEM INSTALLATION AND COMMISSIONING INSTRUCTIONS CONTENTS General ............................................................................... 3 Before Installation ............................................................. 3 Installation ......................................................................... 3 Wiring ................................................................................. 4 XL800 Series Power Consumption .........
PAGE 2
General Excel 800 Troubleshooting...............................................................31 Testing Wiring Connections..........................................31 Troubleshooting on the XCL8010AU Controller............31 Power LED (green) .................................................31 Alarm LED (red) ......................................................32 LONWORKS Service LED..........................................32 C-Bus Tx and Rx LEDs...........................................
PAGE 3
Excel 800 Installation WARNING This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions manual, may cause interference to radio communications. It has been tested and found to comply with the limits for a Class A computing device pursuant to Subpart J of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment.
PAGE 4
Wiring Excel 800 Wiring WARNING All wiring to the XL800 controller is unsupervised, except as noted. Risk of electric shock or equipment damage! All circuits are power limited, except for AC power circuits, relay contacts and other circuits as noted. ► Subpanel and Controller power must remain OFF until Controller is checked. All field wiring terminals accept 24 AWG to 14 AWG (0.25 mm2 to 2 mm2) conductors except as noted. All wiring must conform to local codes, ordinances, and regulations.
PAGE 5
Excel 800 Wiring XL800 Series Power Consumption I/O Modules When selecting the appropriate power supply, the power consumption of the XL800 modules must be taken into account. Variants of I/O Modules There are two variants of I/O modules: Table 3.
PAGE 6
Wiring Excel 800 ANALOG INPUT LonWorks BUS MODULES BINARY INPUT ANALOG OUTPUT PANEL BUS MODULES XCL8010AU CONTROLLER MODULE XFL822AU XFL823AU XFL824AU XFR824AU XFR822AU XF821AU XF822AU XF823AU XS821-22 XS823 LonWorks or Panel Bus 6 XFR825AU XF824AU Fig. 2.
PAGE 7
Excel 800 Description of the XCL8010AU Controller Module Description of the XCL8010AU Controller Module Overview PC or HMI EXCELON I/O MODULES NO CONNECTION LonWorks BUS C-BUS Fig. 3. Connections to the XCL8010AU Controller Legend 1 Power supply for I/O modules 2 I/O Bus communication terminals 3 LONWORKS interface 4 LONWORKS service button 5 LONWORKS service LED 6 C-Bus Tx LED 7 C-Bus Rx LED 8 Reset button 9 HMI interface (for field use, only) 10 Fig. 4.
PAGE 8
Description of the XCL8010AU Controller Module 24 VAC CONTROLLER POWER SWITCH Excel 800 120 VAC, 60 HZ LINE INPUT CONTROLLER POWER ON * H N G MAIN LINE VOLTAGE 120 VAC, 60 HZ TERMINAL “G“ MUST BE CONNECTED TO A GOOD EARTH GROUND. FUSE F1 (2 AMPS) PART NUMBERS ARE AS FOLLOWS: –HONEYWELL PART NO. 14000485-007 (AVAILABLE FROM HONEYWELL BRANCH LOCATIONS, ONLY) –BUSSMAN PART NO. AGC-2 –LITTLEFUSE PART NO.
PAGE 9
Excel 800 Description of the XCL8010AU Controller Module CONTROLLER TRANSFORMER CONTROLLER SUPPLY 24 VAC 48 VA G 70 ~ 71 72 H BLK N WHT G GRN BRN BLK 3 1 4 24 V 50 VA 14507351-001 429P156A E1A 1052 XXXX COM 1 MAIN LINE (120 VAC, 60 Hz) TERMINAL “G” MUST BE CONNECTED TO A GOOD EARTH GROUND. 1 GRN 120 V 2 1 MECHANICALLY SECURED TO SUBPANEL WITH MOUNTING SCREW Fig. 7. Typical 14507287-007 Power Module wiring I/O Module Overview Table 5.
PAGE 10
Description of the XCL8010AU Controller Module Technical Data Corresponding Terminal Sockets Table 6.
PAGE 11
Excel 800 Description of the XCL8010AU Controller Module 4 Locate separate from and below all building exhaust fans and upstream of any prevailing winds. CAUTION 5 Exhaust to outside of building. Risk of electric equipment damage! 6 Locate airflow differential switch. 7 Locate UL-listed damper pressure / position indicator per damper installation instructions.
PAGE 12
Description of the XCL8010AU Controller Module Excel 800 XCL8010AU, I/O Modules on Single Rail ► Connect XCL8010AU Controller Module and I/O modules ROOM 1 using the bridge connectors. This provides power supply and communication connection. No further wiring is necessary. 71 72 LonWorks 73 I/O MODULE 74 75 XCL8010AU 12 LonWorks 76 I/O MODULE 77 78 Multiple Rails in Single Cabinet The multiple rails of a controller system are connected in series.
PAGE 13
Excel 800 Description of the XCL8010AU Controller Module Panel Bus modules Panel Bus modules 75 76 77 78 71 72 73 74 75 71 72 73 74 XCL8010AU 76 77 11 12 13 14 1 2 3 4 78 75 76 77 78 71 72 73 74 LonWorks Bus modules 75 76 77 78 71 72 73 74 Fig. 12. Mixed bus system – correct wiring Panel Bus modules LonWorks Bus modules 75 76 77 78 71 72 73 74 75 71 72 73 74 XCL8010AU 76 77 11 12 13 14 1 2 3 4 78 75 76 77 78 71 72 73 74 Fig. 13.
PAGE 14
Mounting/Dismounting Modules Excel 800 LONWORKS Bus Topologies 44 LOCK The LONWORKS Bus is a 78-kilobit serial link that uses transformer isolation so that the bus wiring does not have a polarity. I.e. it is not important which of the two LONWORKS Bus terminals are connected to each wire of the twisted pair. The LONWORKS Bus does not need to be shielded on the controller module side.
PAGE 15
Excel 800 Mounting/Dismounting Modules Mounting/Dismounting Controller/Sockets Mounting Sockets NOTE: When using both Panel Bus and LONWORKS Bus I/O modules in an Excel 800 System, group both Panel Bus modules (light-gray) and LONWORKS Bus I/O modules (dark-gray), e.g., on different rails. Up to 10 Panel Bus I/O modules can be mounted to one side of the XCL8010AU. In total, up to 16 Panel Bus I/O modules can be mounted to one controller.
PAGE 16
Mounting/Dismounting Modules Excel 800 Fig. 21. Releasing latch Fig. 19. Connecting terminal sockets with bridge connector NOTE: Bridge connectors transmit both communication signals and power supply between modules. Removing bridge connectors will interrupt the transmission of both communication signals and power supply between the modules.
PAGE 17
Excel 800 Mounting/Dismounting Modules Setting the C-Bus Termination Switch ► Set the C-Bus termination switch S1 appropriately. Fig. 23. Locking the electronic module NOTE: Fig. 25. C-Bus termination switch S1 The red locking mechanism will not close if the electronic module is not properly mounted. Dismounting Electronic Modules Table 11.
PAGE 18
Mounting/Dismounting Modules Excel 800 Connecting Laptops (XL-Online/CARE) Features ► Connect a laptop (on which e.g., XL-Online or CARE has been installed) to the HMI interface or LONWORKS interface of the XCL8010AU Controller Module by means of – the XW885 cable or – the XW585 cable connected with an XW586 Cable.
PAGE 19
Excel 800 Mounting/Dismounting Modules C-Bus Tx LED and Rx LED HMI Interface The XCL8010AU Controller Module is equipped with a Tx LED (status: yellow/OFF) and an Rx LED (status: yellow/OFF). The XCL8010AU Controller Module is equipped with an HMI Interface for the connection of HMIs, e.g., XI582 Operator Interface or a laptop (with XL-Online/CARE). C-Bus 1 2 Fig. 29. C-Bus Tx LED (1) and Rx LED (2) Fig. 31.
PAGE 20
Mounting/Dismounting Modules Alarm and Power LEDs Excel 800 Watchdog Status The XCL8010AU Controller Module is equipped with an alarm LED and a power LED. Table 19. Watchdog status (terminal 4) status signal on terminal 4 Failure (= alarm) 24 V Normal operation 0V Modem Interface NO CONNECTION. I/O Bus Switch S2 The XCL8010AU Controller Module features a 2-position I/O Bus switch S2. Fig. 32.
PAGE 21
Excel 800 Description of the I/O Modules Description of the I/O Modules C-Bus Termination Switch S1 The XCL8010AU Controller Module features a 3-position CBus termination switch S1. Common Features This switch must be set in accordance with the given C-Bus configuration. Switches Located on the Terminal Socket Table 23.
PAGE 22
Description of the I/O Modules Excel 800 Terminals Analog Input Modules 71 COM A Types of Analog Input Modules 72 Table 25.
PAGE 23
Excel 800 Description of the I/O Modules XFL821AU Connection Examples 400 OHM 1 18 1 2 25 2 12 1 2 SHIELD 25 SHIELD 0(4) to 20 mA 0 to 10 V 0(4) to 20 mA (VIA EXTERNAL 500 OHM RESISTOR). 0 TO 10 VDC 5 14 22 10 11 12 25 3 13 1 2 SHIELD VMP 25 SHIELD Pt1000 NTC20kW Fig. 37.
PAGE 24
Description of the I/O Modules Excel 800 Terminals Analog Output Modules Types of Analog Output Modules Table 27. Excel 800 Analog Output Modules type description housing XF822 Panel Bus Analog Output Module light-gray XFR822 Panel Bus Analog Output Module with manual overrides light-gray XFL822 LONWORKS Bus Analog Output Module dark-gray XFLR822 LONWORKS Bus Analog Output Module with manual overrides dark-gray XS821-22 terminal socket light-gray Fig. 39.
PAGE 25
Excel 800 Description of the I/O Modules Modules with Manual Overrides The XFR822AU/XFLR822AU Analog Output Modules are equipped with manual overrides: one rotary knob for each analog output. The manual overrides can be set manually to either "auto" or "0 ─ 110%".
PAGE 26
Description of the I/O Modules Excel 800 Terminals Binary Input Modules 71 COM A Types of Binary Input Modules 72 Table 30.
PAGE 27
Excel 800 Description of the I/O Modules Status LEDs The status LEDs can be configured individually for use as either alarm LEDs (red/green) or as status LEDs (yellow/OFF [default]). Given a state of "logical ON," the LED will be lit (yellow or red). XF823AU Connection Examples 1 13 1 2 25 2 14 SHIELD 5 TO 24V 2 MIN. 25 MS 3 1 MIN. 25 MS 15 1 CONTACT SUITABLE FOR LOW VOLTAGE (GOLD). 2 PROTECTED SWITCHING UP TO 40 VDC / 24 VAC. 5 TO 24 VDC 1 ~ 120V PT1000 NTC20kW Fig. 43.
PAGE 28
Description of the I/O Modules Excel 800 Terminals Relay Output Modules 71 COM A Types of Relay Output Modules 73 Table 33. Excel 800 Relay Output Modules type description 74 Panel Bus Relay Output Module light-gray XFR824 Panel Bus Relay Output Module with manual overrides light-gray XFL824 LONWORKS Bus Relay Output Module dark-gray XFLR824 LONWORKS Bus Relay Output Module with manual overrides dark-gray XS824-25 terminal socket; can be fitted with long (red) cross connector (incl.
PAGE 29
Excel 800 Description of the I/O Modules Table 34. Description of Relay Output Module terminals terminal signal comment Permissible Loads Table 35. Permissible loads of Relay Output Modules 2-wire communication bus COM a 71, 75 (LON/Panel Bus) 2-wire communication bus COM b 72, 76 (LON/Panel Bus) 24 V~ 73, 77 Power supply 24 V~0 74, 78 Power supply REL1 N.O. Relay 1 N.O. contact 11 REL1 N.C. Relay 1 N.C.
PAGE 30
Description of the I/O Modules Excel 800 Connection Examples 71 COM A 72 73 74 COM A COM B 24 V~ 24 V~0 COM B 24 V~ 24 V~0 NO 11 NO 21 NO 31 NO 41 NO 51 NO 61 NC 12 NC 22 NC 32 NC 42 NC 52 NC 62 COM 13 COM 23 COM 33 COM 43 COM 53 COM 63 CON 14 CON 24 CON 34 CON 44 CON 54 CON 64 75 71 COM A 76 72 COM B 77 73 78 74 24 V~ 24 V~0 25 1 2 M 14507287 SERIES POWER MODULE Fig. 47.
PAGE 31
Excel 800 Troubleshooting Troubleshooting Testing Wiring Connections The push-in terminals feature small holes (1 mm in diameter) which can be used to measure the signals. ► Insert a probe (1) as shown on the right. Fig. 49.
PAGE 32
Excel 800 Alarm LED (red) Table 38. XCL8010AU alarm LED case 1 2 alarm LED meaning remedy OFF Normal operation No action necessary ON Watchdog alarm output is powered – The controller has encountered a hardware problem - or - ► Try powering down and then – The application has a fault - or - powering up the XCL8010AU. ► If problem persists, check and – if necessary – reload the application.
PAGE 33
Excel 800 Troubleshooting Table 39. XCL8010AU LONWORKS service LED case When can it occur? meaning remedy 1 Anytime Node is configured and running normally No action necessary 2 Power up of controller Bad node hardware ► Replace hardware 3 Power up of controller Bad node hardware ► Replace hardware 4 Power up / reset Node lacks application.
PAGE 34
Excel 800 I/O Modules Troubleshooting ► Check if the power supply voltage level is OK and that there is no high voltage (> 24 VAC or > 40 VDC) connected to the inputs/outputs of the XF821AU, XFL821AU, XF822AU, XFL822AU, XFR822AU, XFLR822AU, XF823AU, and XFL823AU I/O modules. ► Replace the problem I/O module with another module of the same kind. – If the problem persists, this is an indication that the problem is caused by the application or incorrect wiring.
PAGE 35
Excel 800 Troubleshooting Service LED of I/O Modules Table 43.
PAGE 36
Excel 800 Manufactured for and on behalf of the Environmental and Combustion Controls Division of Honeywell Technologies Sàrl, Rolle, Z.A. La Pièce 16, Switzerland by its Authorized Representative: Automation and Control Solutions Honeywell GmbH Böblinger Strasse 17 71101 Schönaich / Germany Phone: (49) 7031 63701 Fax: (49) 7031 637493 http://ecc.emea.honeywell.com Subject to change without notice.