Owner’s Manual CT30/CT33 Low-voltage Thermostat Getting started Check to make sure your package includes the following items: Wire labels Caution card Wall anchors and mounting screws (2 each) CT30/CT33 thermostat Cover plate Before you begin, make sure you have: • Screwdriver • Hammer • Level (optional) • Pencil • Drill bit (3/16” for drywall, 7/32” for plaster) ® U.S. Registered Trademark. Patents pending. Copyright © 2005 Honeywell International Inc. All rights reserved.
Owner’s Manual Remove your old thermostat 1 Turn off power at heating/cooling system (or fuse/circuit-breaker panel). 2 Remove cover and thermostat, but leave wallplate with wires attached. Leave wallplate in place Is there a sealed tube containing mercury? If so, see mercury notice below. Old thermostat Cover MERCURY NOTICE: Do not place your old thermostat in the trash if it contains mercury in a sealed tube.
CT30/CT33 Low-voltage Thermostat Label wires and remove old wallplate Use a screwdriver to disconnect wires one by one.As you disconnect each wire, wrap it with the label matching the letter on your old thermostat. (Adhesive labels are supplied in your thermostat package.) Remove the old wallplate only after all wires are labeled. Be careful not to let loose wires fall into the wall opening.
Owner’s Manual Mount thermostat base 1 Drill holes at pencil-marked locations (3/16” holes for drywall, 7/32” holes for plaster). 2 Use hammer to tap anchors into holes until flush with wall. 3 [Optional] Pull wires through cover plate (if needed to cover marks left by your old thermostat). 4 Connect wires first (see below), then insert screws. Check level if desired, then tighten screws. Optional cover plate Thermostat base Wire connections 1 Match each labeled wire with same letter on terminal.
CT30/CT33 Low-voltage Thermostat Set adjustment lever (CT30 only) 1 Separate cover from thermostat, and remove the plastic insert. 2 Use a pencil to move the adjustment lever to the proper setting for your system (see table below). Your system Setting Gas or oil furnace (less than 90% efficiency) 0.4 Electric furnace (any type) 0.3 High efficiency furnace (more than 90% efficiency) 0.8 Hot water system 0.8 Gas/oil steam or gravity system 1.
Owner’s Manual Operation Temperature setting Move lever to adjust desired indoor temperature. System off (CT33 only) Move lever to far left to turn off heating system.
CT30/CT33 Low-voltage Thermostat Limited Warranty Honeywell warrants this product to be free from defects in the workmanship or materials, under normal use and service, for a period of one (1) year from the date of purchase by the consumer. If at any time during the warranty period the product is determined to be defective or malfunctions, Honeywell shall repair or replace it (at Honeywell's option).
Need Help? For assistance with this product please visit www.honeywell.com/yourhome or call Honeywell Customer Care toll-free at 1-800-468-1502 Automation and Control Solutions Honeywell International Inc. Honeywell Limited-Honeywell Limitée 1985 Douglas Drive North 35 Dynamic Drive Golden Valley, MN 55422 Scarborough, Ontario M1V 4Z9 www.honeywell.com/yourhome Printed in U.S.A. on recycled paper containing at least 10% post-consumer paper fibers. ® U.S. Registered Trademark.
Manual del usuario CT30/CT33 Termostato de bajo voltaje Lista de comprobación previa a la instalación Asegúrese de que el paquete contenga los siguientes elementos: Rótulos para los cables Termostato CT30/CT33 La placa de cubierta Tarjeta de advertencia Soportes de pared y tornillos de montaje (2 cada uno) Herramientas y materiales necesarios • Destornillador • Martillo • Nivel (optativo) • Lápiz • Mecha de taladro (3/16” para mampostería en seco, 7/32” para yeso) ® U.S. Marque déposée.
Manual del usuario Remueva su viejo termostato 1 Desconecte la alimentación en el sistema de calefacción/refrigeración (o en el panel de fusibles/disyuntor). 2 Retire la cubierta y el termostato,pero deje los cables unidos a la placa de montaje. Deje la placa de montaje en su lugar ¿Existe algún tubo sellado que contenga mercurio? Si es así, consulte el aviso sobre mercurio que figura abajo.
Termostato de bajo voltaje CT30/CT33 Rotule los cables y retire la vieja placa de montaje Use un destornillador para desconectar los cables uno a uno.A medida que desconecte cada cable, péguele alrededor el rótulo con la misma letra que figura en su viejo termostato. (En el paquete de su termostato se incluyen rótulos autoadhesivos.) Retire la vieja placa de montaje sólo después de haber rotulado todos los cables. Tenga cuidado de no dejar que los cables sueltos caigan en el hueco de la pared.
Manual del usuario Coloque la placa de montaje 1 Taladre orificios en las posiciones marcadas. Orificios de 3/16” para mampostería en seco. Orificios de 7/32” para yeso. 2 Con un martillo golpee suavemente los soportes de pared e introdúzcalos en los orificios hasta que queden al ras de la pared. 3 [Opcional] Tire de los cables a través de la cubierta (si fuese necesario para cubrir las marcas dejadas por su viejo termostato). 4 Conecte primero los cables (ver abajo), luego inserte los tornillos.
Termostato de bajo voltaje CT30/CT33 Coloque la palanca de ajuste en posición (CT30 únicamente) 1 Separe la cubierta del termostato y retire la lámina de plástico 2 Con un lápiz mueva la palanca de ajuste hasta la posición apropiada para su sistema. (Ver tabla a continuación). Su sistema Ajuste Estufa de gas o petróleo (menos del 90% de eficiencia) 0.4 Estufa eléctrica (cualquier tipo) 0.3 Estufa de alta eficiencia (más del 90% de eficiencia) 0.8 Sistema de agua caliente 0.
Manual del usuario Instrucciones de manejo Ajuste de temperatura Mueva la palanca para ajustar la temperatura deseada en el interior. Sistema apagado (CT33 únicamente) Mueva la palanca hacia el extremo izquierdo para apagar el sistema de calefacción.
Termostato de bajo voltaje CT30/CT33 Garantía limitada Honeywell garantiza que, a excepción de la batería y en condiciones de uso y servicio normales, este producto no tendrá defectos de fabricación ni de materiales durante un (1) año a partir de la fecha de compra por parte del consumidor. Si durante ese período de garantía, el producto resulta defectuoso o tiene problemas de funcionamiento, Honeywell lo reparará o reemplazará (a criterio de Honeywell).
¿Necesita ayuda? Consulte sobre este producto en www.honeywell.com/yourhome o llamando sin cargo a atención al cliente de Honeywell 1-800-468-1502 Automation and Control Solutions Honeywell International Inc. Honeywell Limited-Honeywell Limitée 1985 Douglas Drive North 35 Dynamic Drive Golden Valley, MN 55422 Scarborough, Ontario M1V 4Z9 www.honeywell.com/yourhome Impreso en EE.UU. en papel reciclado que contiene, por lo menos, un 10% de papel ya usado. ® Marca registrada en EE.UU.