H8951-NA1 3G/4G Router User Manual 5.5.2 NAT DNAT configuration rule DNAT is used to replace the destination address of packets accessing external network, router will replace the destination address of packet accessing external network into the user custom settings. Step 1 Log-on WEB GUI of H8951-NA Cellular Wi-Fi Router. Step 2 Click “Forward > NAT” to open “NAT” tab. Figure 5-30 NAT tab Step 3 Click “Add” to add a new NAT rule.
H8951-NA1 3G/4G Router User Manual Figure 5-31 DNAT rule configuration Step 4 Select “DNAT” in NAT Type, to configure DNAT rule parameter.
H8951-NA1 3G/4G Router User Manual Parameter Details Operation Original port The port of external IP, the port need to be replaced Value area: 1~65535 Mapping address Internal IP address e.g. 192.168.8.1 Mapping port The port of Internal IP address Value area :1~65535 Step 5 Single click “save” icon to finish. ---END SNAT configuration rule SNAT is the source address translation, and its role is to translate source address of IP packets into another address.
H8951-NA1 3G/4G Router User Manual Table 5-20 SNAT rule instruction Parameter Details Operation Protocol Convert some kind of protocol packets into address The source address need to be replaced Manual input Original Address Dropdown List all tcp udp icmp Format1:A.B.C.D Format2: A.B.C.
H8951-NA1 3G/4G Router User Manual Figure 5-33 MASQ configuration Step 4 Configure MASQ rule parameter.
H8951-NA1 3G/4G Router User Manual are priorities between static routing and policy routing: policy routing higher priority than static routing. Step 1 Log-on WEB GUI of H8951-NA Cellular Wi-Fi Router. Step 2 Click “Forward > Routing” to open “NAT” tab, as Figure 5-49. Figure 5-34 Static Routing Interface Step 3 Click “Add” to add a new static route, configure interface as Figure 5-50 and Figure 5-51.
H8951-NA1 3G/4G Router User Manual Figure 5-36 Policy Routing Interface Parameter Instruction as Table 5-24. Table 5-22 Static Routing Parameter Instruction Parameter Details Operation To select “Static Route” or “Policy Route” Basic Setting Routing Type Dropdown List When Routing Type is “Static Route” Network Gateway Type Set the destination IP address and subnet mask of static route Manual input Specify gateway type of static routing, includes: Dropdown List Gateway Format1: A.B.C.
H8951-NA1 3G/4G Router User Manual Parameter Details Operation Network It can be configured when “static IP” is selected in source type, by adding IP address or subnet manually. Manual input When source type is policy route, need to manually set source network address of policy router Dropdown List Source Interface Gateway Type Gateway Priority modem Set the next hop IP of policy route Format1: A.B.C.
H8951-NA1 3G/4G Router User Manual Step 1 Log-on WEB GUI of H8951-NA Cellular Wi-Fi Router. Step 2 Click “Forward > QoS” to open “QoS” tab, as Figure 5-52. Figure 5-37 QoS interface Step 3 QOS configuration parameter, configuration parameter instruction as Table 5-25.
H8951-NA1 3G/4G Router User Manual Parameter Details Option Manual input Format1: A.B.C.
H8951-NA1 3G/4G Router User Manual Figure 5-38 RIP interface Parameter Instruction as Table 5-26. Table 5-24 RIP Parameter Instruction Parameter Details Operation RIP Service Enable or disable RIP Service Click the button to select. Redistribute Connected Enable or disable Redistribute Connected Click the button to select. Redistribute Static Enable or disable Redistribute Static Enable or disable Redistribute Kernel Enable Disable Click the button to select.
H8951-NA1 3G/4G Router User Manual Figure 5-39 RIP route configuration interface Step 4 Configure RIP route parameter instruction, as Table 5-27.
H8951-NA1 3G/4G Router User Manual OSPF configuration OSPF (Open Shortest Path First) protocol is one of the (Interior Gateway Protocol), the most widely used IGP, for a single AS (autonomous system) in the routing decisions for large networks. OSPF business can be based whether the user needs to be configured at the factory H8951-NA Cellular Wi-Fi Router. Step 1 Log-on WEB GUI of H8951-NA Cellular Wi-Fi Router. Step 2 Click “Forward > OSPF” to open “OSPF” tab, as Figure 5-55.
H8951-NA1 3G/4G Router User Manual Parameter Details Operation Redistribute Kernel Enable or disable Redistribute Kernel Click the button to select Enable Disable Step 3 Click “Add” to add a new OSPF route, configuration interface as Figure 5-56. Figure 5-41 OSPF route configuration interface Step 4 Configure RIP route parameter instruction, as Table 5-29.
H8951-NA1 3G/4G Router User Manual Dropdown List br0 modem eth1 eth0 Click the button to select cost network Interface Name The interface of the router Interface Attribute Configure the router interface attribute, include cost and network Cost Configure the cost of the router interface, used to learn routing table Manual input Configure the network type of the router interface Network Type(when the interface attribute is network) Value area:1-65535 Dropdown List broadcast no
H8951-NA1 3G/4G Router User Manual Step 2 See “4.3.1 Login WEB GUI Step 3 Click “VPN > VPDN” to open “VPDN” tab. Figure 5-42 VPDN configuration Step 4 Click “Add” to add a new VPDN rule. Figure 5-43 VPDN rule configuration Step 5 Configure VPDN rule parameter.
H8951-NA1 3G/4G Router User Manual Parameter Details Operation Interface name Name of this VPDN rule Cannot be modified after save. protocol VPDN protocol includes Select from Dropdown List, cannot be modified after save. L2TP PPTP Service IP or Domain IP or domain of server to be visited To input the IP or domain of server to be visited. Username Username of server to be visited To input the username. Password Password of server to be visited To input password.
H8951-NA1 3G/4G Router User Manual GRE (Generic Routing Encapsulation, Generic Routing protocol encapsulation) specifies how to use a network protocol to another network protocol encapsulation method. The main purpose of the GRE protocol, there are two: internal protocol encapsulation and private address encapsulation.
H8951-NA1 3G/4G Router User Manual Parameter Details Operation Local virtual IP Virtual IP address of local tunnel Format: interface type A.B.C.D/M. Peer virtual IP Virtual IP address of peer tunnel Format: interface type A.B.C.D/M. Interface type To choose “interface” or “static IP” Select from Dropdown List. Local Extern interface This parameter will need to be set if “interface” is selected in “interface type”. Choose any connected interface as external interface Select from Dropdown List.
H8951-NA1 3G/4G Router User Manual Figure 5-46 IPSec tab Step 3 Click “Add” to add a new IPSec rule. There are 3 phases for IPSec configuration: 3.
H8951-NA1 3G/4G Router User Manual Figure 5-47 IPSec phase 1 configuration Table 5-30 IPSec Phase 1 Parameter instruction Parameter Details Operation Select To select which phase of IPSec, phase 1, phase 1 or phase IPSec Select “Phase 1” Policy Name Name of phase 1, mainly to match phase “IPSec” To input the name of phase 1. Cannot be changed after save.
H8951-NA1 3G/4G Router User Manual Parameter Details Operation Authenticatio n To select authentication Select from Dropdown List, presently only “PSK” supported Pre Share Key To set pre share key Max 24 letters Self Identify To set the self ID of IPSec To input the ID, need to match the ID of other side Match Identify To input the match ID of IPSec To input match ID, need to match ID of other side IKE Lifetime Life time of IKE key Value area: 120~86400 Unit: second Group Name Select gro
H8951-NA1 3G/4G Router User Manual Figure 5-48 IPSec phase 2 configuration Table 5-31 IPSec Parameter instruction Parameter Details Operation Select To select which phase of IPSec, phase 1, phase 1 or phase IPSec Select “Phase 2” Policy Name Name of phase 2, mainly to match phase “IPSec” To input the name of phase 2.
H8951-NA1 3G/4G Router User Manual Parameter Details Operation PFS To open or close PFS Select from Dropdown List Lifetime IPSec SA key life time Value area: 120~86400 Unit: second Transport Mode Supports tunnel, transport and auto. Select from Dropdown List Local Subnet Set local subnet No need to set for “transport” mode, only for “auto” and “tunnel”. Format: A.B.C.D/M Remote Subnet To set local subnet No need to set for “transport” mode, only for “auto” and “tunnel”. Format: A.B.C.
H8951-NA1 3G/4G Router User Manual Parame ter Details Operation Select To select which phase of IPSec, phase 1, phase 1 or phase IPSec Select “IPSec” Interfac e Name Name of this phase Input name Match Phase1 To select a matching name of “phase1” Select from Dropdown List.
H8951-NA1 3G/4G Router User Manual Figure 5-50 OpenVPN configuration page Step 3 Configure OpenVPN parameter. The parameter instruction is shown in Table 2-1. Table 5-33 OpenVPN parameter instruction Parameter Detail Operation OPENVPN Service Enable OPENVPN Service. Click button options: Enable Disable Basic Setting Working Modem Supports two working modes: Dropdown list options: Client mode: client type mode Select the required working mode from dropdown list.
H8951-NA1 3G/4G Router User Manual Parameter Detail Operation Dev Dev represents the network interface type, and supports two types: Dropdown list options: Tun(OSI Layer 3):Simulates network layer device to operate the third layer data packets, such as IP packets Select the required working mode from dropdown list. Demand consistent with peer. Tap(OSI Layer 2):Equates to an Ethernet device to operate the second layer data packets, such as Ethernet data frame.
H8951-NA1 3G/4G Router User Manual Parameter Detail Operation Authenticatio n Configuring the VPN data transfer mode: Dropdown list options: SSL: encrypt the network connection in transport layer, high safety factor. Select the required data transfer type from dropdown list. Text: transport with text form during transmission, low safety factor Ca Specifies the file path for the client CA certificate WORD type,max 32 bytes.
H8951-NA1 3G/4G Router User Manual 5.7 System configuration 5.7.1 Overview “System” can let you know the status of router, firmware upgrading and other maintenance. 5.7.2 Local Log Step 1 Log-on WEB GUI of H8951-NA Cellular Wi-Fi Router. Step 2 Click “System > Local Log” to open “Local Log” tab. Figure 5-51 Local Log tab Step 3 Select type of “Local Log” and then click “View” to see log. Click “Clear” to clear the log info in the “Log Table”, and click “Export” to export log in your local PC.
H8951-NA1 3G/4G Router User Manual To see “local log”, “remote log” must be enabled. ---END 5.7.3 Remote Log Step 1 Log-on WEB GUI of H8951-NA Cellular Wi-Fi Router. Step 2 Click “System > Remote Log” to open “Local Log” tab. Figure 5-52 Remote Log tab Step 3 Configure “Remote Log” parameter.
H8951-NA1 3G/4G Router User Manual 5.7.4 Clock Step 1 Log-on WEB GUI of H8951-NA Cellular Wi-Fi Router. Step 2 Click “System > Clock” to open “Clock” tab. Figure 5-53 “NTP” Time Synch. Figure 5-54 Manual Time Synch. Type Step 3 Set “clock” parameters.
H8951-NA1 3G/4G Router User Manual Time Synch. Type Type to synchronize system time Select “Manual” “NTP” or When select “NTP” in “Time Synch. Type” NTP Server IP or Domain IP or domain of NTP server Select from Dropdown List NTP Server Backup Backup NTP server Manual input server domain or IP address NTP Synch. Interval Interval for NTP client to check time with NTP Server. E.g.
H8951-NA1 3G/4G Router User Manual Figure 5-55 Account tab Step 3 Set account parameters. Table 5-36 Account parameter instruction Parameter Details Operation Account Type Visit the router on web Account Level Level of account to login router Select from Dropdown List Current Username Current username Showing user name Old password Current password To input current PW New Username New username Manual input, max 64 word type. New Password New password Manual input, max 64 word type.
H8951-NA1 3G/4G Router User Manual Parameter Details Operation Default: 80 Step 4 Click “Save” to finish configuration. After saving, user needs to login again. ---END 5.7.6 Network Test Network Test This function includes Ping function and Trace router function. Step 1 Log-on WEB GUI of H8951-NA Cellular Wi-Fi Router. Step 2 Click “System > Network Test” to open “Network Test” tab.
H8951-NA1 3G/4G Router User Manual Parameter Details Operation tested domain to be tested Ping To use Ping to test link Click “Ping” Trace To use Trace command to test hops from the router to destination Click “Trace” Result Test result ---END 5.7.7 Files Firmware Setting H8951-NA Cellular Wi-Fi Router supports upgrade firmware locally. Step 1 Log-on WEB GUI of H8951-NA Cellular Wi-Fi Router. Step 2 Click “System > Files” to open “Files” tab.
H8951-NA1 3G/4G Router User Manual Step 3 Click “Browse” to select upgrading file and then click “Upgrade”. ---END CFE mode upgrading If upgrading file is larger than 6MB, CFE mode upgrading shall be used to upgrade. Step 1 Add an IP address 192.168.1. Figure 5-58 Add an IP address Step 2 Press the RESET/DEF interface. Do not release it. Hold it, meanwhile power on router, till 30 seconds, and connection to PC is built properly. Then release RESET/DEF interface. Step 3 Input 192.168.1.
H8951-NA1 3G/4G Router User Manual Figure 5-59 CFE mode upgrading Step 4 Click “Browse” to select upgrading file, and then click “Upload” to begin upgrading. Figure 5-60 CFE upgrading page Upgrading will need 4-6 minutes, if RUN light is on, upgrading is OK. You can also PING br0 address on your PC (ping 192.168.8.1 –t). if Ping ok, upgrading is OK. ---END Backup setting H8951-NA Cellular Wi-Fi Router supports to backup and to recover configuration file.
H8951-NA1 3G/4G Router User Manual Figure 5-61 Backup setting page After import, router will reboot automatically. “Key”: if key is input when export configuration file, this key need to be input in import. Not more than 8 digits for key. Factory setting H8951-NA Cellular Wi-Fi Router has function to resume factory configuration.
H8951-NA1 3G/4G Router User Manual Figure 5-62 Factory setting page Save: to save the current setting as default factory configuration setting. Load: to resume default factory setting. Patch operation function H8951-NA Cellular Wi-Fi Router supports to delete patch.
H8951-NA1 3G/4G Router User Manual Figure 5-63 Patch operation Delete: to delete patch. Reboot Click “Reboot” to restart the router.
H8951-NA1 3G/4G Router User Manual Figure 5-64 Reboot --END 5.8 Status 5.8.1 Overview Status provides the basic info, network status info, router info of H8951-NA Cellular Wi-Fi Router. 5.8.2 Base Information Step 1 Log-on WEB GUI of H8951-NA Cellular Wi-Fi Router. Step 2 Click “Status > Base information” to open “Base Information” tab.
H8951-NA1 3G/4G Router User Manual Figure 5-65 Base Information tab Table 5-38 Base information Parameter instruction Parameter Details Router Model Router model info Router SN Router Serial No info Hardware version Router hardware version info Software version OS and application software info. Operation 5.8.3 LAN Step 1 Log-on WEB GUI of H8951-NA Cellular Wi-Fi Router. Step 2 Click “Status > LAN” to open “LAN” tab.
H8951-NA1 3G/4G Router User Manual Table 5-39 LAN Parameter instruction Parameter Details LAN status To show current LAN interfaces status. IP address To show the LAN IP address. Subnet Mask Subnet mask of LAN interface. MAC address To show the MAC address of the router. Operatio n 5.8.4 WAN Step 1 Log-on WEB GUI of H8951-NA Cellular Wi-Fi Router. Step 2 Click “Status > WAN” to open “WAN” tab. There are three types of WAN status: static IP/DHCP/PPPOE.
H8951-NA1 3G/4G Router User Manual Figure 5-68 DHCP WAN status Figure 5-69 PPPoE WAN status Table 5-40 WAN Parameter instruction Parameter Details WAN status To show the current WAN is used or not WAN Type To show the current WAN type Local IP To show the local IP of WAN interface Subnet mask To show the subnet mask MAC address To show the MAC address of the router Operatio n PPPoE for WAN type 107
H8951-NA1 3G/4G Router User Manual Parameter Details Status To show the link status of WAN interface PPPoE Local IP To show the router IP distributed by PPPoE Remote IP To show IP of PPPoE server Operatio n 5.8.5 Modem Step 1 Log-on WEB GUI of H8951-NA Cellular Wi-Fi Router. Step 2 Click “Status > Modem” to open “Modem” tab.
H8951-NA1 3G/4G Router User Manual Table 5-41 Modem Parameter instruction Parameter Details Modem Select To show the current modem name Up tome To show the current on line time of the modem Operatio n Unit: second Modem Status To show the Router’s status to link to the mobile network Network type Current network type of the SIM in use signal Signal of mobile network Value area: 1-31 IP Address To show the external network IP address which the router links DNS To show which DNS router is usi
H8951-NA1 3G/4G Router User Manual Table 5-42 Routing table Parameter instruction Parameter Details Operation Static route Network IP address the router can reach Subnet Mask IP network the router can reach. It is used together with “Network” Gateway Next hop IP address which the router will reach interface Interface from router to gateway metric Route No which the router reaches destination IP Policy route Priority Priority the router select route ---END 5.
H8951-NA1 3G/4G Router User Manual 6 Typical application About this chapter Chapter Content 6.1 Overview Summary some typical application of H8951-NA Cellular Wi-Fi Router 6.2 Awake function How to awake H8951-NA Cellular Wi-Fi Router if not auto-dial 6.3 Parameter select Parameter switch to achieve SIM backup function 6.4 VPN H8951-NA Cellular Wi-Fi Router VPN setting 6.5 Timing Task Set Timing task on H8951-NA Cellular Wi-Fi Router 6.
H8951-NA1 3G/4G Router User Manual parameter setting Let us check an example: Figure 6-1 Wake up/trigger setting example Effect By this setting, after router power on, if there are data trigger or you could call/SMS SIM1 or SIM2 number from 8618888888888 to trigger corresponding SIM online, modem will dial online, After 3600s, router will offline. Or you could use 8612222222222 to call SIM, make the router offline. Please notice, to enable this function, the SIM must support phone and/or SMS function.
H8951-NA1 3G/4G Router User Manual 6.3 Parameter select Typical case H8951-NA Cellular Wi-Fi Router provides the parameter switching function, or temporarily stop working links can be replaced. For example: When L2TP link is working for some reason does not work, you can switch to an alternate PPTP or IPSec link. H8951-NA Cellular Wi-Fi Router configured parameters based on switching rules, multi-link switching and good communication ensures the reliability of the network.
H8951-NA1 3G/4G Router User Manual Figure 6-3 Parameter select setting 1 114
H8951-NA1 3G/4G Router User Manual Figure 6-4 Parameter select setting 2 When L2TP link is working for some reason disconnected from the server, the router will perform parameter switching in Command "check icmp", through IP ping to detect whether router interrupt with network operators; after 3 IP ping fails, the router will switch to the PPTP link, connecting to maintain the server, continue to work.
H8951-NA1 3G/4G Router User Manual Figure 6-5 Build IPSec PC1 connect H8951-NA then build IPSEC link by VPN function of H8951-NA with company router. I assume using IPSec tunnel mode, H8951-NA end local network 192.168.86.1/24, company server end 192.168.99.1/24, by IPSEC, two LAN could communicate.
H8951-NA1 3G/4G Router User Manual Figure 6-7 IPSec Phase 2 Figure 6-8 IPSec Company router server should have same setting but the identity and subnet setting for the company router server should be the opposite of those for H8951-NA Cellular Wi-Fi Router. Result After setting H8951-NA Cellular Wi-Fi Router and company router parameter, they can connect each other by IPSEC, and ping peer subnet, you could check status by click “view” button.
H8951-NA1 3G/4G Router User Manual Figure 6-9 IPSec status ~ # ping 192.168.99.1 -I 192.168.86.1 PING 192.168.99.1 (192.168.99.1) from 192.168.86.1: 56 data bytes 64 bytes from 192.168.99.1: seq=0 ttl=255 time=1569.360 ms 64 bytes from 192.168.99.1: seq=1 ttl=255 time=769.937 ms --- 192.168.99.1 ping statistics --2 packets transmitted, 2 packets received, 0% packet loss round-trip min/avg/max = 769.937/1169.648/1569.360 ms 6.
H8951-NA1 3G/4G Router User Manual Figure 6-11 Router online Figure 6-12 Router off line Figure 6-13 Router reboot 119
H8951-NA1 3G/4G Router User Manual 7 FAQ About this chapter Chapter Content 7.1 Hardware failure Possible hardware failure during using H8951-NA Cellular Wi-Fi Router and how to handle them 7.2 Dial online problem Possible problem during dialing and how to handle them 7.3 VPN Possible problem when connecting VPN 7.4 Web configuration Possible WEB configuration problem and how to handle them 7.1 Hardware Failure 7.1.
H8951-NA1 3G/4G Router User Manual 7.1.2 SIM Slot Phenomenon Cannot insert SIM card Possible Reason SIM slot damaged SIM card wrong direction Solution SIM slot damaged, please contact us to repair Chec k the SIM card direction, please make sure the SIM card is inserted correctly 7.1.
H8951-NA1 3G/4G Router User Manual 7.2 Dial Online Problem 7.2.1 Dial discontinue Phenomenon H8951-NA Cellular Wi-Fi Router discontinue during dialing, dial failure Possible Reason SIM card network type do not match SIM charges owed Power supply do not match Modem setting wrong Solution Change to a suitable SIM card Recharge SIM card Change to suitable power supply Change Modem setting, please check related chapter 7.2.
H8951-NA1 3G/4G Router User Manual Solution Replace SIM card Re-install SIM card 7.2.4 Poor Signal Phenomenon H8951-NA Cellular Wi-Fi Router no signal or poor signal Possible Reason Antenna connect wrong Area signal weak Solution Check the antenna and re-connect it. Contact Telecom Operator to confirm signal problem Change to high-gain antenna 7.2.
H8951-NA1 3G/4G Router User Manual Solution Make sure Modem is online Set the correct port to VPDN VPDN parameter wrong Check VPDN peer server 7.3.2 VPN cannot communicate Phenomenon VPN already connect, but cannot communicate Possible Reason Router table is configured wrong VPN peer server is configured wrong Solution Add related Router table Check VPN peer server setting 7.3.
H8951-NA1 3G/4G Router User Manual Power supply problem Wrong firmware Power off during updating router Solution Check setting, disable the function which may cause reboot Change to a suitable power supply Ask technical support for suitable firmware Power off during updating router, please make sure power supply normal 7.4.
H8951-NA1 3G/4G Router User Manual Solution If power supply does not match, please change then update again If firmware version, format do not match, please change then update again If power off during updating, please update again 7.4.5 Update failure in WEB GUI Phenomenon Updating by WEB GUI, failed and cannot visit WEB GUI again Possible Reason Firmware oversize cause updating failure Solution Using CFE mode to update again, and router will restore to factory mode.
FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
ConnectingThings F14 - F16, Tower A, Building 14, No.12, Ganli 6th Road, Longgang District, Shenzhen 518112, China. +86-755-88864288-5 +86-755-83404677 hongdianchina www.hongdian.com sales@hongdian.