HT-IP006N Manual Book
Security Solutions Partner CONTENTS 1 WELCOME........................................................................................................................................................................ 3 1.1 FEATURES..................................................................................................................................................................................................3 1.2 PACKING LIST.......................................................................
Security Solutions Partner 1 WELCOME This is an integrated wireless IP Camera. It combines a high quality digital Video Camera with network features and a powerful web server. You can access this camera from anywhere on your local network or over the Internet. The basic function is transmitting remote video on your IP network. The high quality video images can be transmitted with 30fps speed on the LAN/WAN by using MJPEG hardware compression technology.
Security Solutions Partner 1.3 Product Views 1.3.1 Front View Figure 1.1 1.3.2 Cable Interface Figure 1.2 Audio Output: The jack is used to plug external speakers or audio output devices. Audio Input: The jack is used to plug external microphones or audio input devices. I/O Alarm Pin: 1 Alarm input (GND), 2 Input, 3 Output A, 4 Output B Network Interface: RJ-45/10-100 base T Network indicator: The green LED will be on when the network is connected. The yellow LED will blink when data is transferred.
Security Solutions Partner default settings. (Please keep the power on when using RESET) Power: DC 12V/2A power supply 1.4 PC System Requirements System configuration requirements: (Example for viewing four IPCAM) CPU: 2.06GHZ or above Memory: 256M or above Network Card: 10M or above Display Card: 64M or above memory Recommendable Operating System: Windows 2000/ XP/ Vista/ 7 1.5 Hardware Instruction Follow the steps below to set up your camera hardware.
Security Solutions Partner Figure1.5 Figure1.6 Figure1.7 After this done, the icon “IP Camera Tool” will be displayed on your desktop automatically.
Security Solutions Partner CAUTION: Before installing and using the product, please read the following precautions carefully and make sure they are fully understood. Use only the power adaptor included with the product. Using unauthorized power adapters may cause damage to your IP Camera. IP Camera terminal shall be installed in an indoor environment where there is no rain or snow. Do not touch the lens of the IP Camera. The optimum focus range has been set before it is delivered out of the factory.
Security Solutions Partner choose the prompt and click the right mouse, choose Network Configuration to set the static IP address of the Camera to the same subnet as LAN. (Figure 2.2) NOTE: If it shows” Subnet doesn’t match, double click to change!”, you can also choose ”Obtain IP from DHCP Server” to get a dynamic IP. (Figure 2.1) 2.1.1 Six Options Choose the IP Camera list and Click right mouse, there are six options: (Figure 1.
Security Solutions Partner Figure2.0 2.1.1.2 Network Configuration In this page, you can configure the Network parameter. Figure2.1 Obtain IP from DHCP server: If clicked, the device will obtain IP from DHCP server. In other words, the camera will have a dynamic IP. (Make sure the Router which the camera is connected to has DHCP function and DHCP is enabled). (Figure 2.1) Figure 2.
Security Solutions Partner Gateway: Make sure it is in the same subnet with your PC’s IP address. Gateway is the LAN IP of your router. DNS Server: IP address of IPS network provider. You can also set it’s the same as the Gateway. NOTE: You can find the Subnet Mask, Gateway, DNS Server from your router, or check the local connection status of your computer to get all the parameters. Normally two DNS servers are optional. Http Port: LAN port assigned for the equipment, default is 80.
Security Solutions Partner Check the IP Camera Tool Version and IP Camera ActiveX Control Version here. 2.2 Camera Login You can access the camera through IP Camera Tool or IE, Firefox, Safari, Google Chrome or other browsers. 1. Double click the IP address of the IP Camera listed (Figure 1.8). The default browser you use will run automatically and open the camera login interface. (Figure 2.6) 2.
Security Solutions Partner Figure 2.6 (1) Active Mode (For IE Browser): available in IE6.0 or above (2) “Server Push Mode”: available in Firefox, Safari, and Google Chrome browser. (3) “Sign in mobile phone”: available for Mobile phones 2.3 For IE Browser Choose Active Mode (For IE Browser), and sign in. Figure 2.
Security Solutions Partner Figure2.8 Figure 2.9 Note: If there is still no live video after running ActiveX, and a red cross shows in the center of the screen, or even just a black screen, please try to enable the ActiveX options in IE security settings. Please do the follow steps: 1. Close the firewall on your computer. 2.
Security Solutions Partner Figure3.0 Figure 3.1 In addition: you can also click “Start” menu->“Internet Explorer”, choose “Internet attributes “ to enter, or via “Control Panel” ->“Internet Explorer”, enter to Security setting. If ActiveX is running, but you still could not see live video, please try using another port number. Don’t use port 80, use other ports such as 128, 1008 etc.
Security Solutions Partner Figure 3.2 NOTE: Make sure that the firewall or anti-virus software doesn’t block the software or ActiveX. If you couldn’t see live video, please close your firewall or anti-virus software, and try again. 2.4 For Safari, Firefox, Google Browser Choose Server Push Mode (For Safari, Firefox, Google Browser), and sign in Server Push Mode doesn’t support ActiveX, so some functions are not available, such as Play, Stop, Record, Audio, Talk etc.
Security Solutions Partner 2.5 For Mobile Phone Choose Sign in mobile phone, and sign in. Mobile phone doesn’t support ActiveX, only some basic functions can be available in this mode. It supports most smartphones with a 3G/4G connection. Usually, if the mobile phone supports network video, then it can work with our IP Camera. Figure 3.4 2.
Security Solutions Partner Figure 3.5 Channels: Our IE software supports 9 channels total. Clicking can get different windows. : Click this one, you can view the main channel of the camera. : Click this one; you can view 4 Channels of cameras that are connected, from CH1 to CH4. : Click this one; you can view 9 Channels of cameras that are connected, from CH1 to CH9. NOTE: If you want to view 4/9 channels, you should set the Multi-Device first (See 3.
Security Solutions Partner OSD Settings: Figure 3.6 OSD: Means “On-Screen Display”, click “Audio video” > “OSD”, set display date and time on the video. Disabled: Click this one, means clear the OSD. Color: Can set the OSD text color as black, yellow, red, white, blue etc. Add time stamp on record: Click this, there will be time OSD on record video files. Figure 3.
Security Solutions Partner Rate and Resolution: Rate: Set video framerate here, from “full-speed to 1fp/5s”. (Figure 3.8) Resolution: Set the resolution to be 160*120/ VGA(640*480)/ QVGA (320*240). (Figure 3.9) NOTE: When doing recording, Rate and Resolution parameter settings is very helpful for getting small sized recording files, the lower parameter to get the smaller file. Figure 3.8 Figure 3.9 TOP Menu: Figure 4.0 : Click it to get live video.
Security Solutions Partner NOTE: For visitor, if you click other menus which visitor don’t have the right to operate it, there will be a pop-up of the login interface (Figure 2.6), please input the user name / password for at least 3 times to login again. 2.8 For Operator When logged in as Operator, you can enter the IP Camera with Operator mode. For operator, it not only supports all the functions which for Visitor, and also supports these functions as below: Figure 4.
Security Solutions Partner Reversal: Click this icon to see the reversal image. Click again, will be back to normal. Mirror: Click this icon to see the mirror image. Click again, will back to normal. NOTE: You can choose Reversal and Mirror function when you set up the camera in a special position. Mode, Bright, Contrast Settings Figure 4.
Security Solutions Partner RECOMMENDATION: Image PT function: Image PT function is recommended, you can control the camera direction on the live video. Double click the right mouse on the live video to enable this function, and you will see a white & transparent arrow on the live video, left click to control direction, eight directions are available. This is very convenient for Pan/Tilt operation. Double click right mouse again to exit. Preset Settings Figure 4.5 : Set Preset Position.
Security Solutions Partner Figure 4.6 3.1 Multi-Device Settings Multi-Device Settings This camera can support max. 9 channels device at the same time. 3.1.1 Set Multi-Device in LAN In the Multi-Device Settings page, you can see all devices searched in LAN. The 1st device is the default one. You can add more cameras listed in LAN for monitoring. This web software supports up to 9 IP Cameras online simultaneously.
Security Solutions Partner Figure 4.7 Click Live Video and then select to see four channels, or click Figure 4.8 24 to see nine channels.
Security Solutions Partner Figure 4.9 3.1.2 Set Multi-Device for WAN If you want to view your cameras from the internet, you have to add these devices by DDNS domain name. Make sure all these cameras you want to add have been set to DDNS successfully. (View 3.7 DDNS Service Settings) Login the first camera by DDNS domain name and port, this camera will be set as the host camera. Figure 5.0 Click Multi-Device, select Multi-Device Settings.
Security Solutions Partner Submit. NOTE: The Alias is optional; you can set the alias as you desire. The Host must be the camera’s DDNS domain name, and without “http://”, it’s not the LAN IP address. If you have several cameras, you can use the same DDNS domain name, just set different port numbers for each different camera. Figure 5.1 Note: Add the other camera in the same way, Click submit to add all of them.
Security Solutions Partner Figure 5.2 Click Live Video and then select to see four channels, or to see nine channels. In this case, you can see all the cameras from a remote position by internet, for example, if you are on the business trip, you can use the first camera’s (Host camera) DDNS to view all the devices via internet Figure 5.3 3.1.3 Upgrade Device Firmware If you want to upgrade the camera, please upgrade Device Firmware first, then upgrade Web UI.
Security Solutions Partner 3.1.4 Restore Factory Settings Click Restore Factory Settings, a pop-up will prompt, select OK, all the parameters will be returned to factory settings, and the device will reboot. Figure 5.5 3.1.5 Reboot Device Click Reboot the device, a pop-up will prompt, select OK, then the device will reboot Figure 5.6 3.2 Network Settings Click Network, will pop-up the prompt as below: 3.
Security Solutions Partner Figure 5.7 If you don’t know Subnet Mask, Gateway, DNS Server, please check the Local Area Connection Status of your computer; it contains all this information, steps as below: 1. Control PanelNetwork ConnectionsLocal Area Connections Support Details 2. Find the local connection icon from taskbar, left click , choose Support Details Figure 5.8 Figure 5.
Security Solutions Partner If you don’t know the DNS Server, you can set it the same as Gateway. If the router supports DHCP function, you can choose “Obtain IP from DHCP Server” to get dynamic IP. Figure 6.0 Http Port: In most cases, you can leave this value as default, if your Internet Service Provider blocks this port, you may change it to another port number such as 85. 3.4 Wireless Lan Settings Figure 6.1 1. Make sure the router is a wireless router. 2. Make sure the Wi-Fi antenna is installed.
Security Solutions Partner Figure 6.3 Figure 6.4 Figure 6.
Security Solutions Partner 3.5 ADSL Settings When connected to the Internet through ADSL directly, you can enter the ADSL username And password obtained from ISP. Figure 6.7 3.6 UPnP Settings Click UPnP Settings to choose Using UPnP to Map Port: Figure 6.8 Select it and click Submit, then the camera will support UPnP port forwarding automatically. It’s helpful for using DDNS, if your router support UPnP, then you do not need do port forwarding in router. Figure 6.
Security Solutions Partner Figure 7.0 There are 2 options: Manufacturer’s DDNS: This domain is provided by manufacturer. Third Party DDNS: This domain is provided by the 3rd party, such as Dyndns, Oray, 3322 etc. Figure 7.1 Third Party DDNS If you use a third party DDNS, please choose the server you use, such as “3322.org” or “dyndns.org” as below: Figure 7.2 Figure 7.3 You have to register an account first, keep the user, password, host, then input it.
Security Solutions Partner Change the camera’s port. The default port of the camera is “80”, please change “80” to any other one you like, such as “81”, “100”, “8091” etc. Click “OK”, the camera will reboot, wait about 30 seconds. Figure 7.4 Make sure the “Subnet Mask”, “Gateway”, “DNS Server” is the same as your router. Set Port Forwarding in the router. This is the most important step. Setting up your port forwarding in your router to the IP of your camera correctly, then the DDNS will work.
Security Solutions Partner BELKIN: 1. Login the router. 2. Choose “Firewall”, select “Virtual Servers” 3. Input the port (except 80) and IP address, then click save. NOTE: The port and IP address should be the same as Camera. Figure 7.6 DLINK: 1. Login the router. 2. Choose “Advanced”, select “Virtual Servers” 3. Input the port, IP address, Protocol, then click save. NOTE: The “public port” & “private port” should be the same as camera’s port, choose the protocol to be “both”. Figure 7.
Security Solutions Partner Step: “Login”>”System”>”Device Info”: Figure 7.8 Figure 7.9 3.8 System Settings Figure 8.0 3.8.1 Device Info You can find the information about Device ID, Firmware Version, Embedded Web UI Version, Alias, Alarm Status, DDNS Status, UPnP Status and MSN status.
Security Solutions Partner Figure 8.1 3.9 Alias Settings Default device name is anonymous. You set any new name for your camera here, then click Submit. Figure 8.2 3.10 Date &Time Settings Set the date and time for your camera. Choose the Clock Time zone of your country. You can choose Sync with NTP Server (Figure 8.3) or Sync with PC Time (Figure 8.4). Figure 8.
Security Solutions Partner Figure 8.4 3.11 Users Settings Eight accounts are acceptable for this system. Here you can set the user names and password as Administrator, Operator or Visitor, the permission for them as below: Visitor: In this mode, you can only view. (Details 2.7) Operator: You can control the direction of IP Camera and set some parameters. (Details 2.8) Administrator: You can setup the advanced configurations of the IP Camera. (Details3.1-3.22) Figure 8.
Security Solutions Partner 3.12 PTZ Settings Figure 8.6 1. Go center on boot: The camera will rotate to the center automatically when it starts 2. PT speed: Set Pan / Tilt speed 3. Upward patrol speed: Set the speed of cruising upward 4. Downward patrol speed: Set the speed of cruising downward 5. Leftward patrol speed: Set the speed of cruising leftward 6. Rightward patrol speed: Set the speed of cruising rightward NOTE: Value 0 means the fastest, value 10 means the slowest.
Security Solutions Partner （1）Backup: Backup IP Camera settings, if you want to save all the current settings that you have set already, you can click Submit, then all the parameters you set will store as a parameters bin file. （2）Restore: Restore IP Camera settings, if you want to change the camera’s settings to a certain status which has a backup, click Browse to load the bin file, then Submit it. Log Figure 8.9 Record User information, including weekday, date, time, user name, visitor IP address etc.
Security Solutions Partner Run your MSN, open the chat dialog, type in the word “url?”, after a few seconds, you will get a reply for the remote access ip address for this ip camera. 3.15 Other Settings Figure 9.0 Here you can configure some additional functions such as Motion Detection, Alarm, IO Linkage, Schedule, FTP Upload, Alarm Mail Alert, Record Path etc. 3.16 Mail Service Settings Set Mail Service Settings to enable the camera send email alert when motion detection triggered.
Security Solutions Partner Figure 9.1 Sender: Make sure the sender mailbox server provider support SMTP, and the mailbox should not enable SSL or TSL encryption too. Receiver: Here you can set four receivers. For receiver, there is no SMTP limitation. SMTP Server: The sender’s SMTP Server. SMTP Port: The sender’s SMTP Port, usually is 25, some SMTP server have its own port such as 587. Need Authentication: If there is SMTP user & password, please select authentication.
Security Solutions Partner again 6) The receiver is denied by the server. Maybe because of the anti-spam privacy of the server 7) The message is denied by the server. Maybe because of the anti-spam privacy of the server 8) The server does not support the authentication mode used by the device Report Internet IP by Mail: If selected, you will receive emails which contain the camera’s internet IP. When camera power on or Internet IP changed, it will send the internet IP by mail.
Security Solutions Partner Click Submit after these settings. Then click Test. You will see the following picture. Figure 9.5 If it prompts error information as follows. 1) Cannot connect to the server. Please check FTP Server is correct or not. 2) Network Error. Please try later. 3) Server Error. 4) Incorrect user or password. Please check the username and password is correct or not. 5) Cannot access the folder. Please be sure the folder exists and your account is authorized 6) Error in PASV mode.
Security Solutions Partner triggered. Figure 9.7 After enable motion detect armed, if there is motion triggered, the Alarm Status will turn to Motion Detect Alarm. (Figure 9.8) Figure 9.8 3.18.2 Motion Detect Sensibility You can choose level 1-10; level 10 means the most sensitive, 1 means the least of all.
Security Solutions Partner Figure 9.9 3.18.3 Alarm Input Armed / IO Linkage on Alarm If you want to connect external alarm devices, when it’s an alarm input device, choose Alarm Input Armed to enable it, when it’s an output device, choose IO Linkage on Alarm to enable it. Figure 10.0 There are two options for Trigger Level. (Figure 10.1) High: When the external alarm device is closed, then the alarm triggered. Low: When the external alarm device is switching off, then the alarm triggered. Figure 10.
Security Solutions Partner Figure 10.2 3.18.4 IO Pins for IO Alarm Linkage Figure 10.3 I/O PINS: 1 .Alarm input 2 Alarm input 3 Alarm output 4 Alarm output Input pins: The input pins can be used for 1-way external sensor input. For example, you may connect a Person Infrared Sensor (PIP) to it for motion detection. When external sensor triggered, IP CAMERA can be programmed to send an email with picture or control the internal relay output.
Security Solutions Partner Left click the frame of the time range, it will turn to blue color, which means the time you chose is alarmed. Click it again, it will turn back to grey, means delete the scheduler. NOTE: Make sure the date & time settings are correct first. (Figure 8.3) ATTENTION: If you don’t choose Scheduler, the camera will alarm anytime when motion triggered. Figure 10.
Security Solutions Partner 3.20 Path Settings Figure 10.8 Here you can set record path and alarm record path for the camera. Figure 10.9 Record Path: Here you can set the manually record path. Click , then start manually recording, the record file will be saved to the specified path here set. Alarm Record Path: Here you can set the alarm record path.
Security Solutions Partner 3.21 Server Push Mode (For Safari, FireFox, Google Browser) Choose Server Push Mode, log in to the camera, you will see the main user interface as shown below: Figure 11.2 NOTE: Server Push Mode does not support ActiveX. Play, Stop, Record, Audio, Talk, Multi-device settings, Path settings functions are controlled by ActiveX, so if you use Safari, Firefox, Google chrome browser, it is impossible to use these options.
Security Solutions Partner Figure 11.3 NOTE: Mobile phone Mode doesn’t support ActiveX. In mobile phone mode, it only supports some easy functions, such as Resolution, Mode, Bright, Contrast, Pan/Tilt control, Snapshot, Reversal, Mirror, IO Linkage functions 4. APPENDIX 4.1 Frequently Asked Questions Note: Any questions you have, please check Network connections first. Check the working status revealed by the indicators on the network server, hub, exchange and network card.
Security Solutions Partner 4.1.3 IP Address configuration Check whether IP address of the IP camera server shares the same subnet as your work station: Click My Computer >Control Panel> Network & Dial-up Connections > LAN > Attributes >Internet Protocols (TCP/IP), and check IP Address and Subnet Mask. Make sure they are in the same subnet when configuring Camera’s IP address manually. 4.1.
Security Solutions Partner So if you use Safari, Firefox, Google chrome, it is impossible to use these functions. 4.1.10 Camera cannot connect wireless If your camera could not connect wireless after you set wireless settings and plug out the cable. Please check whether your settings are correct or not. (Details: Wireless LAN settings) Normally, camera can’t connect wireless mainly because of wrong settings. Double check the SSID, Encryption share key, Channel, should be the same as your wireless router.
Security Solutions Partner 4.2 Default Parameters Default network Parameters IP address: dynamic obtain Subnet mask: dynamic obtain Gateway: dynamic obtain DHCP: Disabled DDNS: factory DDNS and third party DDNS Username and password Default administrator username: admin Default administrator password: No password 5. Specifications Specification: Image Sensor Audio Image Sensor 1/4" Color CMOS Sensor Display Resolution 640 x 480 Pixels(300k Pixels) Lens 3x Optical Zoom Mini. Illumination 0.
Security Solutions Partner Alarm Output Infrarde light Power PC System Requirements Certification 66 IR LEDs, night visibility up to 15 meters Dimension 165*195*130 mm Power Supply DC 12V/2.0A Power Consumption 10 Watts (Max.) Operate Temper. Environment 1 Channel relay Output Operating 0° ~ 55°C Humidity 20% ~ 85% non-condensing Storage Temper. -25°C ~ 55° Storage Humidity 0% ~ 90% non-condensing CPU 2.0GHZ or above (suggested 3.0GHz) Memory Size 256MB or above (suggested 1.
