Instructions for your DIAL-A-MATIC CLEANER WITH AUTOMATIC POWER DRIVE Model 1170
ON/OFF SWITCH BAG INDICATOR SUCTION DIAL F$sq ,f&&$$ NOZZLE HOSE I WRAP-AROUND FURNITURE GUARD Your Power Drive Cleaner has been completely assembled at our factory. It is ready for use without further assembly or adjustment. THREE POSITION HANDLE Storage, operating 2 and low (for reaching under low furniture). The handle can be lowered by stepping on the pedal at the left rear of cleaner. The handle should always be in storage position when cleaning tools are used.
For greater convenience and ease of operation, this Deluxe cleaner provides you with an exclusive Automatic Power Drive feature. The Automatic Power Drive Control is built into the handle of the cleaner. This automatic drive propels the cleaner forward and backward at a variable rate of speed controlled entirely by (you) the operator. (Fig. 1) Forward - To operate the cleaner in the forward position using the A-utomatic Power Drive, push the handle grip forward. (Fig.
THIS IS THE “HEART” OF YOUR NEW HOOVER POWER DRIVE CLEANER Your new Hoover Power Drive is the most powerful upright cleaner ever built. To handle the wide range of pile depth of modern carpets and rugs, two (2) adjustment features have been provided. These features are Automatic Rug Adjustment and Suction Adjustment as explained in the following paragraphs. When used properly, they will assure the best cleaning efficiency and ease of operation. Automatic Rug Adjustment.
E CLEANING TOOLS (See Page 4 for setting Suction Control Dial when using tools). 1. TUFFLEX HOSE Double vinyl reinforced with nylon mesh for long, trouble-free life. The light flexible hose has a vinyl tab, so it can be hung on the cleaner or on a hook in a closet. 2. TELESCOPING WAND When you require extra length for cleaning bare floors or hard-to-reach places, attach the telescoping extension wand. To lengthen the wand, press down on the plastic latch and extend wand until it locks in place.
HELPFUL HINTS Don’t Pick Up Tacks Your cleaner is powerful. It can pick up tacks, pins, paper clips, etc. However, hard sharp objects should not be picked up by the cleaner. They may clog or damage the hose and the throw-away bag. Take Care of The Cord Wind it loosely, on the cover latch and knob on Suction Control Dial, to avoid strain. Snap clip-on plug onto cord. To remove cord, turn cover latch. (See inset). Don’t run cleaner over the cord - it may damage the insulation.
ose on the cleaner carries the dirt from the nozzle to the throw-away bag. lf the hose becomes obstructed (which may happen if the bag is overfilled), remove it and clear it. Pull the hose end from the bottom of the bag housing and unscrew hose end by turning in a clockwise direction. Turn cleaner over, remove bottom plate (Fig. 1, Page 8) and pull hose from cleaner. Clean hose and reinsert it in the cleaner. NOTE: ALWAYS DISCONNECT CORD FROM ELECTRICAL OUTLET BEFORE REPLACING PARTS.
THE BELTS There are two belts on your Hoover cleaner. The belts control the speed of the agitator and the power drive pulley and are important for the efficient operation of your cleaner. Because of this, when buying new belts, you should always insist on genuine Hoover belts. Some other belts on the market, not manufactured under the Hoover design and quality controls, do not operate the agitator or Power Drive correctly and may damage your Hoover cleaner. When To Replace Belts.
THE BRUSHES When brushes a&worn and bristles do not touch the edge of a card held across the nozzle, they should be replaced. Always replace both brushes at the same time to maintain cleaning efficiency. To Replace Brushes. Remove bottom plate, belt and agitator following directions given on Page 8. 1. Turn end plates of agitator in opposite directions until one plate comes off. , ;,,;- ” ,. ,; ,,,. 2 2. Then pry out end section as shown in illustration. 3.
ELECTRIC KNIVES AUTOMATIC TOASTERS STAINLESS STEEL COFFEEPOT ELECTRIC FRY PANS BLENDERS HANDMIXER CANOPENERKNIFE SHARPENER PROFESSIONAL-TYPE UAlD nDVCD
DIAL-A-MATIC CLEANERS .
SERVICE Service and genuine Hoover replacement parts may be obtained from Hoover Factory Service Stations listed on white insert. For Service in Warranty Period follow instrudtions set forth in Guarantee. When ordering new parts make sure that you always mention the model number of the product. Lubrication--The motor is equipped with one ball bearing and one sleeve bearing. These bearings contain sufficient lubrication for the life of the motor.