HOOVER HOBS USER INSTRUCTIONS ❐ HGD 640 SGH ❐ HGD 640 GH ❐ HGH 640 SX ❐ HGH 640 X ❐ HGH 640 SW ❐ HGH 640 W ❐ HGH 640 SB ❐ HGH 640 B ❐ HGD 750 X ❐ HGD 750 SGH ❐ HGD 750 GH
TECHNICAL CHARACTERISTICS BUILT IN HOBS Burners/hotplates Type / reference Flame failure device Fish burner PES DC ø 110 mm Double ring burner UR ø 110 mm Ultra rapid burnes SR ø 51 mm Semirapid burner R ø 71 mm Rapid burner Griddle 174x160 mm Griddle 229x379 Electric plate Ø 80 PE Electric plate Ø 145 PE Electric plate 160x265 mm PE Installed gas Type/Power G20 20mbar* (METHANE) G30 28-30 mbar (GPL) Installation class Voltage/ Frequency V/Hz Electrical imput power Electronic ignition Product dimension WDX
B C 2 IE GB
INSTRUCTIONS FOR THE INSTALLER INSTALLATION The Purchaser is responsible for the installation of the hob. The Manufacturer does not accept any responsibility for any damage or loss resulting from incorrect installation, and as such this will not covered by the Manufacturer’s Guarantee. The hob may be installed in any worktop which is heat resistant to a temperature of 100° C, and has a thickness of 25 - 45 mm. The dimensions of the insert to be cut out of the worktop are in shown in Fig. 1.
If a hob of 60 cm is fitted above an oven which is not equipped with fan cooling system it is recommended that openings are created within the built in furniture to ensure correct air circulation. The size of these openings must be at least 300 cm2 and placed as shown in fig. 4. When a 75 cm hob is fitted over a built in oven, the latter must be fan cooled. FIG.
ELECTRICAL CONNECTION Warning - this appliance must be earthed This appliance is designed for domestic use only. Connection to the mains supply must be made by a competant electrician, ensuring that all current regulations concerning such installations are observed. The appliance must only be connected to a suitably rated spur point, a 3 pin 13 amp plug/socket is not suitable. A double pole switch must be provided and the circuit must have appropriate fuse protection.
ELECTRICAL CONNECTION Check the data on the rating plate, located on the outside of the unit, to ensure that the supply and input voltage are suitable. Before connection, check the earthing system. By Law, this appliance must be earthed. If this regulation is not complied with, the Manufacturer will not be responsible for any damage caused to persons or property. If a plug is not already attached, fit a plug appropriate to the load indicated on the rating plate. The earth wire is coloured yellow/green.
To prevent any potential damage to the hob please carry out the installation following this sequence: GB IE 1/2 GAS CONICAL A) As illustrated, assemble parts in sequence: A) fixed pipe B) washer C) Elbow fitting with tapered thred connection 2) Tighten the joints with the Spanners, remembering to twist the pipes into position. 3) Attach fitting C to mains gas supply using rigid copper pipe or flexible steel pipe.
Table of gas consumption G20/G25 Working burner large medium maxi double ring G30 G31 Ø gas jet Ø gas jet 1/100 mm 1/100 mm 120 80 93 61 2x94 2x65 2x94 2x65 fish 2x94 X dimension according to Gas type 1W = 0,860 kcal/h G20 20mbar G30 29mbar G31 37mbar G25 25mbar G20 G30 G25 G31 STD. Dim kW 2,65 1,5 3,3 3,3 l/h G20 252 143 314 314 g/h G30 193 109 238 238 g/h G31 189 107 236 236 Qn kW 2,5 1,45 3,1 3,1 l/h G25 277 161 343 343 min.Dim kW 0,65 0,38 0,9 0,9 reg. air 4 mm 2 mm 15 mm 13 mm reg.
When you have carried out the new gas regulation, replace the old gas rating plate on your appliance with one (supplied with hob) suitable for the type of gas for which it has been regulated. USE OF HOB USER INSTRUCTIONS This appliance must only be used for the purpose for which it is intended, domestic cooking, and any other use will be considered improper and could therefore be dangerous. The Manufacturer will not be responsible for any damage or loss resulting from improper use.
MAINTENANCE AND CLEANING Before cleaning the Hob, ensure the appliance has cooled down. Remove the plug from the socket or (if connected directly) switch off the electricity supply. When cleaning the enamelled, varnished or chrome sections, use warm soapy water or a non caustic detergent. For stainless steel use an appropriate cleaning solution. Hotplates should only be cleaned with a cotton cloth coated with vaseline or seed oil. Never use abrasives, corrosive detergents, bleaching agents or acids.
