EN User instructions ® HLSI 500GT DISHWASHER
CONTENTS pag. pag. pag. pag. pag. pag. pag. pag. pag. pag. pag. pag. pag. pag. pag. pag. pag. pag. pag. pag.
■ The door should not be left in the open position since this could present a potential hazard ( es. tripping ). SAFETY INSTRUCTIONS There are certain basic safety rules which are valid for any domestic appliance. ■ Leaning or sitting on the open door of the dishwasher could cause it to tip over. Installation WARNING ! Knives and other utensils with sharp points must be loaded in the basket with their points down or placed in a horizontal position.
Water connection ■ The hose can be hooked over the side of the sink, but it must not be immersed in water, in order to prevent water from being syphoned back to the machine when this is in operation (fig. 4Y). Connecting the outlet hose IMPORTANT The appliance must be connected to the water mains using new hose-sets. The old hose-sets should not be reused. 1 ■ The outlet hose should disharge into a standpipe, making sure that there are no kinks (fig. 4).
WATER SOFTENER UNIT * The softener unit is set in the factory at level 4 (d4) as this satisfies the requirements of the majority of users. Depending on the source of the supply, water contains varying amounts of limestone and minerals which are deposited on the dishes leaving whitish stains and marks. The higher the level of these minerals present in the water, the harder the water is.
ADJUSTMENT OF THE UPPER BASKET LOADING DISHES 1 A standard daily load is represented in figs. 1 and 2. Upper basket (fig. 1) Using the upper basket If 27 cm to 31 cm plates are normally used, load them onto the lower basket after the upper basket has been placed in its upper position and proceed as detailed below: 1 ■ The upper basket is provided with mobile racks hooked to the sides of the basket, which can be regulated into two positions: upright and lowered. 1. Pull out the upper basket; 2.
■ The lower basket is fitted with a special adjustable central rack (fig. 3 and 4). This permits stable and optimum loading, even when the size and/or shape of the dishes is non-standard. - POSITION “A”: for a standard load, or one that excludes pans, salad bowls and the like. - POSITION “B”: for dishes which, although standard size, have a particular shape (very deep bowls, square dishes or ones without borders etc.). A B A standard daily load is represented in fig. 6.
■ the effectiveness of detergents containing the built in water softener/salt depends on the hardness of your water supply. Check that the hardness of your water supply is within the effective range given on the detergent packaging. TYPES OF DETERGENT LOADING THE DETERGENT Detergent tablets The detergent IMPORTANT It is essential to use a detergent that is specifically designed for dishwashers either in powder, liquid or tablet form.
LOADING THE RINSE AID CLEANING THE FILTERS The rinse aid The filter system (fig.A “4”) consists of: The rinse aid, which is automatically released during the last rinsing cycle, helps the dishes to dry quickly and prevents spots and stains forming. a flat gauze that continuously filters the wash water; Filling the rinse aid container dark a micro filter, located beneath the gauze, that traps the tiniest particles ensuring a perfect rinse.
PRATICAL HINTS How to make savings How to get really good wash results ■ If you want the dishwasher to give a complete wash, place the dishes in the dishwasher at the end of each meal and if necessary turn on the COLD RINSE cycle to soften the food remains and remove bigger particles of food from the new load of dishes. When the dishwasher is full start the complete wash cycle programme.
DESCRIPTION OF THE CONTROL PANEL ■ Press the "ON/OFF" button . The display will show the "recommended" programme, or the last programme used. PROGRAMME SELECTION AND SPECIAL FUNCTIONS (Use in conjunction with programme guide) ■ To set another programme, press the "PROGRAMME SELECTION" button ("PROGR.").
■ The display will show the "recommended" programme. "IMPULSE" programmes The “IMPULSE” programmes use an impluse washing technology, which reduces consumption, noise and increases performances. IMPORTANT The “intermittent” working of the washing pump MUST NOT BE considered a malfunction, it is a characteristic of the impulse washing so must be considered a normal function of the programme. ■ At this point a new programme can be set.
WATERCONTROL-SYSTEM The dishwasher is able to signal a series of faults in the display. AUTOMATIC FAULT SIGNALS FAULTS CAUSE SOLUTION E2 appears on the display and the alarm sounds. No water (inlet hose closed). Turn off the dishwasher, open the inlet hose and reset the cycle. E3 appears on the display and the alarm sounds. The machine cannot drain water. Check if the drain tube is bent or if the siphon or filters are clogged. If the problem persists, contact Customer Service.
Intended for rapid washing of very dirty dishes. Family 65 - 75°C Intended for everyday dishwashing. Two final rinses ensure a high level of hygiene and cleanliness. UNIVERSAL 50 - 60°C (“RECOMMENDED” PROGRAMME) Once a day - for normal soiled pans and any other items that have been left all day for washing. Daily 45 - 55°C Fast cycle, for “normally” dirty dishes - intended for frequent washes and normal loads. Night 55°C Quietest washing cycle.
IDENTIFYING MINOR FAULTS FAULT Should the dishwasher fail to operate, before contacting the Service Centre, make the following checks: FAULT 1 - Machine completely dead 2 - Machine does not draw water 3 - Machine does not discharge water 4 - Machine discharges water continuously 5 - Spray arms are not heard to rotate 6 - On electronic appliances without a display: one or more indicator lights flashing quickly. CAUSE CAUSE See causes for no.
Hoover guarantees all parts of this product for 5 years from the date of purchase. During that time Hoover will replace or repair all defective parts free of charge, except for parts subject to fair wear and tear such as belts. The call out fee and labour costs are chargeable after the first 12 months.
HOOVER SERVICE FOR YOUR LOCAL ENGINEER PLEASE CALL OUR NATIONAL NUMBER 08705-400600 EIRE 0818 200021 10.10 - 41034648 - www.graficaestampa.