IT EN FR DE Guida pratica all’uso User instructions Mode d’emploi Bedienungsanleitung ® DYM 893/T LAVASTOVIGLIE DISHWASHER LAVE-VAISSELLE GESCHIRRSPÜLER
INDICE Norme generali di sicurezza Installazione Alimentazione idrica Caricare il sale Regolazione del cesto superiore Caricamento delle stoviglie Informazioni per laboratori di prova Caricamento detersivo Tipi di detersivo Caricamento brillantante Pulizia filtri Consigli pratici Pulizia e manutenzione ordinaria Descrizione dei comandi Dati tecnici Scelta dei programmi e funzioni particolari Waterblock Elenco dei programmi Impianto di decalcificazione Ricerca piccoli guasti pag. 4 pag. 6 pag. 7 pag. 9 pag.
scano i pericoli del suo utilizzo. Evitare che i bambini giochino con l’apparecchio o che si occupino della sua pulizia e manutenzione senza supervisione. NORME GENERALI DI SICUREZZA ■ Questo apparecchio è destinato ad un uso in ambienti domestici e simili come per esempio: ■ I bambini dovrebbero essere supervisionati per assicurarsi che non giochino con l'apparecchio.
■ In generale è sconsigliabile l'uso di adattatori, prese multiple e/o prolunghe. ■ Per il numero massimo di coperti fare riferimento alla tabella "DATI TECNICI". ■ Non tirare il cavo di alimentazione, o l'apparecchio stesso, per staccare la spina dalla presa di corrente. ATTENZIONE! Coltelli ed altri utensili con l’estremità appuntite devono essere collocati nel cesto con le punte rivolte verso il basso o in posizione orizzontale. ■ Non esporre l'apparecchio ad agenti atmosferici (pioggia, sole, ecc.).
■ Qualora fosse necessario trasportare manualmente la macchina disimballata, non impugnare la porta in basso, ma aprire leggermente la porta e sollevare impugnando il ripiano superiore. Questo apparecchio è conforme alle Direttive Europee: ■ 2006/95/EC (LVD); ■ 2004/108/EC (EMC); ■ 2009/125/EC (ErP); ■ 2011/65/EU (RoHS); e a tutte le successive. ■ Per le modalità di installazione degli apparecchi da incasso, fare riferimento all'apposito capitolo o alle istruzioni allegate al presente libretto.
ALIMENTAZIONE IDRICA IMPORTANTE L’apparecchio deve essere connesso alla rete idrica, solo con i nuovi tubi di carico forniti in dotazione. I vecchi tubi di carico non devono essere riutilizzati. 1 ■ I tubi di carico e scarico possono essere orientati indifferentemente verso destra o verso sinistra. IMPORTANTE La lavastoviglie può essere allacciata all'impianto dell'acqua fredda o calda purchè non superi i 60°C.
■ L'estremità ricurva del tubo di scarico può essere appoggiata al bordo di un lavello, ma non deve rimanere immersa nell'acqua, per evitare il risucchio nell'apparecchio durante il programma di lavaggio (fig. 4Y). Collegamento allo scarico d'acqua ■ Infilare il tubo nell'impianto di scarico, senza creare pieghe (fig. 4). ■ Nel caso di installazione sotto piano continuo, la curva deve essere fissata immediatamente sotto il piano nel punto più alto possibile (fig. 4Z).
CARICARE IL SALE ■ Il contenitore ha una capacità di circa 1,5÷1,8 kg di sale e, per una efficace utilizzazione dell'apparecchio, è necessario riempirlo periodicamente a secondo della regolazione del proprio impianto di decalcificazione. ■ La comparsa di macchie biancastre sulle stoviglie è generalmente un indice importante di mancanza del sale. ■ Sul fondo della macchina, è sistemato il contenitore del sale che serve a rigenerare l'apparecchio decalcificatore.
REGOLAZIONE DEL CESTELLO SUPERIORE 1 Utilizzando abitualmente piatti da 29 cm a 32,5 cm di diametro, caricarli nel cesto inferiore dopo aver spostato quello superiore nella posizione più alta, procedendo nel seguente modo: 1. Estrarre il cesto superiore; 2 2. Impugnare il cesto da entrambi i lati e tirarlo verso l’alto (fig. 1).
CARICAMENTO DELLE STOVIGLIE Un carico standard giornaliero è rappresentato nelle fig. 1 e 2. Utilizzo del cesto superiore Cesto superiore (fig. 1) ■ Il cesto superiore è dotato di supporti mobili agganciati alla sponda laterale, in grado di assumere 4 posizioni. 1 ■ Nella posizione abbassata (A-A1) i supporti servono per appoggiarvi tazze da the, caffè, lunghi coltelli e mestoli. Sulle estremità dei supporti stessi, si possono appendere i bicchieri a forma di calice. A A1 Cesto superiore (fig.
■ Il cesto inferiore è dotato di una speciale griglia mobile centrale (fig. 3 e 4) utile per avere sempre il carico stabile e ottimale dei piatti, anche quando le dimensioni e/o la forma sono diverse da quelle standard. 5 - POSIZIONE "A": per un carico di piatti standard o per un carico esclusivo di pentole, insalatiere, ecc… A - POSIZIONE "B": per piatti di forma particolare anche se di dimensioni standard (fondine molto profonde, quadrate o senza bordo, ecc…).
Un carico standard giornaliero è rappresentato nella figura 7. Utilizzo del terzo cesto ■ Il terzo cesto è progettato per riporre al suo interno tutti gli oggetti ruba-spazio, quali stoviglie e utensili di piccole dimensioni oppure lunghi e piatti. Liberando i cesti inferiori da questi oggetti, il carico di stoviglie ingombranti risulta più agevole, permettendo ad esempio la sistemazione contemporanea di pentole e piatti nel cesto inferiore. Terzo cesto (fig.
CARICAMENTO DETERSIVO Il detersivo IMPORTANTE Utilizzare esclusivamente detersivi in polvere, liquidi o in pastiglie specifici per lavastoviglie. B Nella lavastoviglie si trova una confezione campione di ”FINISH” che assicura ottimi risultati di lavaggio. Dopo aver versato il detersivo nel contenitore, richiudete lo sportellino, prima spingendolo (1) ed infine premendo leggermente su di esso (2) fino a sentire lo scatto d'arresto.
e alle avvertenze indicate sulla confezione del detersivo combinato che si intende utilizzare; TIPI DI DETERSIVO Detersivi in pastiglie ■ l’efficacia dei prodotti che rendono non necessario l’utilizzo del sale dipende dalla durezza dell’acqua di alimentazione dell’apparecchio. Verificare allo scopo che la durezza dell’acqua sia compresa nell’intervallo di funzionamento indicato nelle istruzioni del detersivo.
CARICAMENTO BRILLANTANTE Il brillantante Questo additivo, che viene immesso automaticamente nell'ultima fase di risciacquo, favorisce una rapida asciugatura delle stoviglie evitando il formarsi di macchie e sedimenti opachi. Caricare il brillantante C Alla sinistra della vaschetta del detersivo, si trova il contenitore del brillantante (fig. A "3"). Per aprire il coperchio, premere in corrispondenza del riferimento posto su di esso e contemporaneamente, tirare verso l'alto la linguetta d'apertura.
PULIZIA DEI FILTRI Il sistema filtrante (fig. A "4") è costituito da: 1 Bicchierino centrale, che trattiene le particelle più grosse di sporco; Piastra, che filtra continuamente l'acqua di lavaggio; Microfiltro, posto sotto la piastra, che trattiene anche le particelle di sporco più piccole assicurando un'ottimo risciacquo. ■ Per ottenere sempre ottimi risultati, è necessario ispezionare e pulire i filtri prima di ogni lavaggio.
CONSIGLI PRATICI Consigli utili per risparmiare ■ Nel caso si volesse lavare a pieno carico, riponete le stoviglie nella macchina appena terminati i pasti, sistemandole in più riprese, effettuando eventualmente il programma AMMOLLO per ammorbidire lo sporco ed eliminare i residui più grossi tra un carico e l'altro, in attesa di eseguire il programma di lavaggio completo.
PULIZIA E MANUTENZIONE ORDINARIA 1 ■ Per pulire l'esterno della lavastoviglie non si devono usare, né solventi (sgrassanti) né abrasivi, ma solo un panno imbevuto di acqua tiepida. ■ La lavastoviglie non richiede alcuna manutenzione speciale, poichè la vasca di lavaggio è autopulente. ■ Pulire regolarmente la guarnizione in gomma dello sportello con un panno umido, eliminando accuratamente eventuali tracce di cibo, o brillantante.
DESCRIZIONE DEI COMANDI A Pulsante "AVVIO/ARRESTO" G Pulsante opzione "SUPER ECO" B Pulsante "SELEZIONE PROGRAMMA" H Pulsante opzione "ALL IN 1" C Pulsante "PARTENZA DIFFERITA" I Spia "ESAURIMENTO SALE" D Pulsante "START"/"RESET" (avvio/annullamento programma) L Spia "ESAURIMENTO BRILLANTANTE" E M Spie "ACTION PRO" Display digitale F N Spie "SELEZIONE OPZIONE" Pulsante "ACTION PRO" O Legenda programmi DIMENSIONI Con piano lavoro Senza piano lavoro 60 x 85 x 60 120 59,8 x 82 x 5
SCELTA DEL PROGRAMMA E FUNZIONI PARTICOLARI Programmi "AUTOMATICI" La lavastoviglie è dotata di un sensore di sporco, in grado di analizzare la torbidità dell'acqua durante tutte le fasi dei programmi "AUTOMATICI" (vedi elenco programmi); grazie a questo dispositivo, i parametri del ciclo di lavaggio vengono adattati automaticamente, in base alla reale quantità di sporco presente sulle stoviglie. Il grado di torbidità dell’acqua è infatti correlato alla quantità di sporco presente sulle stoviglie.
Fine del programma ATTENZIONE! Se si apre lo sportello mentre la lavastoviglie è nella fase di asciugatura, viene attivato un segnale acustico intermittente, per avvisare che il ciclo non è ancora terminato. La fine del programma verrà indicata tramite un segnale acustico (se non disattivato) della durata di 5 secondi, ripetuto per 3 volte ad intervalli di 30 secondi. Il display e tutte le spie si spegneranno.
Pulsante "PARTENZA DIFFERITA" Esclusione segnalazione acustica di FINE PROGRAMMA Questo pulsante permette di programmare l'avvio del ciclo di lavaggio, con un ritardo compreso tra 1 e 23 ore. La segnalazione acustica di fine programma può essere disattivata nel seguente modo: Per impostare la partenza ritardata procedere nel seguente modo: IMPORTANTE Iniziare la procedura SEMPRE dalla condizione di lavastoviglie spenta.
Memorizzazione dell'ultimo programma utilizzato 4. Premere nuovamente lo stesso pulsante (sul display verrà visualizzato "A1" che sta ad indicare che la memorizzazione è attivata). Per abilitare la memorizzazione dell'ultimo programma utilizzato procedere nel seguente modo: 5. Spegnere la lavastoviglie premendo il tasto "AVVIO/ARRESTO" per rendere effettiva la nuova impostazione. Per disattivare la memorizzazione, seguire la stessa procedura.
WATERBLOCK Lo scopo del «Waterblock» è di rendere ancora più sicuro il Vostro apparecchio, in particolare quando in casa non c’è nessuno. Infatti, il «Waterblock» intercetta eventuali perdite d’acqua che potrebbero causare allagamenti, dovuti ad anomalie di funzionamento della macchina o a scoppi o tagli delle tubazioni di gomma e particolarmente del tubo di carico dell’acqua.
ELENCO DEI PROGRAMMI Lavaggio con prelavaggio Per i programmi con prelavaggio, si consiglia di aggiungere una seconda dose di detersivo (MAX. 10 grammi) direttamente nella lavastoviglie. • /( ) = LO SVOLGIMENTO DEI PROGRAMMI "AUTOMATICI" VIENE OTTIMIZZATO, GRAZIE ALL' INTERVENTO DEL SENSORE DI SPORCO CHE ADATTA I PARAMETRI DI LAVAGGIO IN FUNZIONE DEL GRADO DI SPORCO DELLE STOVIGLIE.
N.D.= OPZIONE NON DISPONIBILE * ••••• ••••• ••••• ••••• •••• •••• •••• ••••• •••• ••••• •••• • Pulsante “SUPER ECO” Pulsante “ALL IN 1” 75°C 140 SI SI SI 75°C 130 SI SI SI 65°C 85 SI SI SI 115/ 125 SI SI SI ( 27 * Svolgimento del Programma media in Durata Minuti Funzioni Facoltative ( ) 50°C/ ( 60°C ) 100/ 120 SI SI SI ( ) 45°C/ ( 55°C ) 70/ 80 SI SI SI 55°C 240 SI SI SI 45°C 170 SI SI SI 45°C 85 SI SI SI 65°C 59 SI SI SI 50°C 24 SI N.D. SI 5 SI N.D.
IMPIANTO DI DECALCIFICAZIONE regolazione è stata impostata dalla * La fabbrica al livello 4 (d4) in quanto questo L'acqua contiene in misura variabile, a seconda delle località, sali calcarei e minerali che si possono depositare sulle stoviglie lasciando macchie e depositi biancastri. Più elevato è il contenuto di questi sali, maggiore è la durezza dell'acqua.
RICERCA PICCOLI GUASTI Se la Vostra lavastoviglie non funzionasse, prima di chiamare il Servizio Assistenza, fare i seguenti controlli: ANOMALIA 1 - Non funziona con qualsiasi programma 2 - Non carica acqua 3 - Non scarica acqua 4 - Scarica acqua in continuazione 5 - Non si sentono ruotare i bracci di lavaggio 6 - Nelle macchine elettroniche senza display: una o più spie lampeggiano rapidamente CAUSA RIMEDIO Spina corrente elettrica non inserita nella presa Inserire spina Tasto O/I non inserito
ANOMALIA CAUSA Vedi cause 5 Controllare Fondo di pentole non perfettamente lavato Croste troppo tenaci, da ammorbidire prima del lavaggio in lavastoviglie Bordo di pentole non perfettamente lavato Posizionare meglio la pentola Spruzzatori parzialmente otturati 7- Se il carico viene parzialmente lavato RIMEDIO Smontare i bracci di lavaggio, svitando le ghiere di fissaggio in senso orario e lavare il tutto sotto un getto d’acqua Le stoviglie non sono sistemate bene Non addossate troppo le stovigl
CONTENTS pag. pag. pag. pag. pag. pag. pag. pag. pag. pag. pag. pag. pag. pag. pag. pag. pag. pag. pag. pag.
above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
■ In general it is not advisable to use adaptors, multiple plugs and/or extension cables. ■ For the maximum place loading, please refer to the "TECHNICAL DATA" table/section. ■ Do not remove the plug from the mains supply socket by pulling the mains cable or the machine itself. WARNING ! Knives and other utensils with sharp points must be loaded in the basket with their points down or placed in a horizontal position. ■ Do not leave the appliance exposed to the elements (rain, sun etc).
■ If it you need to move the machine after removing the packaging, do not try to lift it by the bottom of the door. Open the door slightly and lift the machine by holding on the top. Appliance complies European Directives: with ■ 2006/95/EC (LVD); ■ 2004/108/EC (EMC); ■ 2009/125/EC (ErP); ■ 2011/65/EU (RoHS) and subsequent amendments ■ For the installation of built-in appliances, please refer to the specific chapter or to the instructions enclosed with the booklet.
WATER CONNECTION IMPORTANT The appliance must be connected to the water mains using new hose-sets. The old hose-sets should not be reused. 1 ■ The inlet and drain hoses can be directed to left or right. IMPORTANT The dishwasher can be connected to either cold or hot water, as long as it is no hotter than 60°C. ■ Water pressure must be between 0,08 MPa and 0,8 MPa. 2 ■ The inlet hose must be connected to a tap so that the water supply can be cut off when the machine is not in use (fig. 1 B).
■ The hose can be hooked over the side of the sink, but it must not be immersed in water, in order to prevent water from being syphoned back to the machine when this is in operation (fig. 4Y). Connecting the outlet hose ■ The outlet hose should disharge into a standpipe, making sure that there are no kinks (fig. 4). ■ When installing the appliance under a worktop the hose pipe clamp must be attached to the wall in the highest possible position under the worktop (fig. 4Z).
■ The salt dispenser has a capacity of between 1.5 and 1.8 kg and, for efficient use of the appliance, it should be refilled from time to time according to the regulation of the water softener unit. LOADING THE SALT ■ The appearance of white stains on dishes is generally a warning sign that the salt container needs filling. ■ On the bottom of the machine there is a container for the salt for regenerating the softener.
ADJUSTMENT OF THE UPPER BASKET 1 If 29 cm to 32,5 cm plates are normally used, load them onto the lower basket after the upper basket has been placed in its upper position and proceed as detailed below: 1. Pull out the upper basket; 2 2. Then grasp the basket from both sides and lift it upwards (fig. 1). a b a Dishes that are bigger than 14 cm in diameter can no longer be loaded onto the upper basket and the mobile supports cannot be used when the basket is in the upper position.
A standard daily load is represented in figs. 1 and 2. LOADING DISHES Upper basket (fig. 1) Using the upper basket 1 ■ The upper basket is provided with mobile racks hooked to the sides of the basket, which can be regulated into 4 positions. ■ In the lowered position (A-A1) the racks may be used for such items as: tea and coffee cups, kitchen knives and ladles. Also glasses with stems may be safely hung on the ends of the racks. A A1 Upper basket (fig.
■ The lower basket is fitted with a special adjustable central rack (fig. 3 and 4). This permits stable and optimum loading, even when the size and/or shape of the dishes is non-standard. 5 - POSITION “A”: for a standard load, or one that excludes pans, salad bowls and the like. - POSITION “B”: for dishes which, although standard size, have a particular shape (very deep bowls, square dishes or ones without borders etc.). A B A standard daily load is represented in fig. 6.
A standard daily load is represented in fig. 7. Using the third basket ■ The third basket has been designed to load items such as utensils of small dimensions or flat and long shaped items. By freeing the lower baskets from these objects, loading big-size items becomes more comfortable and easier, making it possible for instance to load plates and pots in the lower basket. Third basket (fig.
LOADING THE DETERGENT The detergent IMPORTANT It is essential to use a detergent that is specifically designed for dishwashers either in powder, liquid or tablet form. B After pouring the detergent into the container, close the lid, firstly pushing (1) and then pressing on it (2) until you hear the click. “FINISH” gives very good results and can be easily obtained.
■ the effectiveness of detergents containing the built in water softener/salt depends on the hardness of your water supply. Check that the hardness of your water supply is within the effective range given on the detergent packaging. TYPES OF DETERGENT Detergent tablets Detergent tablets of different manufacturers dissolve at different speeds, for this reason, during short programmes, some detergent tablets may be not fully effective, because they are not completely dissolved.
LOADING THE RINSE AID The rinse aid The rinse aid, which is automatically released during the last rinsing cycle, helps the dishes to dry quickly and prevents spots and stains forming. Filling the rinse aid container C The rinse aid container can be found to the left of the detergent container (fig. A "3"). To open the lid, push the reference mark and, in the same time, pull the tab of opening. It is always advisable to use rinse aid that is specifically designed for dishwasher.
CLEANING THE FILTERS The filter system (fig.A “4”) consists of: 1 a central container that traps the larger particles; a flat gauze that continuously filters the wash water; a micro filter, located beneath the gauze, that traps the tiniest particles ensuring a perfect rinse. ■ To achieve excellent results every time, the filters should be checked and cleaned after each wash. ■ To remove the filter unit, simply turn the handle anticlockwise (fig. 1).
PRATICAL HINTS How to make savings ■ If you want the dishwasher to give a complete wash, place the dishes in the dishwasher at the end of each meal and if necessary turn on the COLD RINSE cycle to soften the food remains and remove bigger particles of food from the new load of dishes. When the dishwasher is full start the complete wash cycle programme.
CLEANING AND MAINTENANCE 1 1b ■ To clean the dishwasher outside, do not use solvents (degreasing action) neither abrasives, but only a cloth soaked with water. ■ The dishwasher does not require special maintenance, because the tank is self-cleaning. ■ Regularly wipe the door gasket with a damp cloth to remove any food remains or rinse aid. 2 ■ Dishwasher cleaning is recommended, in order to remove limestone deposits or dirt.
DESCRIPTION OF THE CONTROL PANEL A B C D "ON/OFF" button E F G Digital display H I L M N O "PROGRAMME SELECTION" button "DELAY START" button "START"/"RESET" button (start/cancelling programme) "ACTION PRO" button "ALL IN 1" option button "SALT EMPTY" light "RINSE AID EMPTY" light "ACTION PRO" lights "OPTION SELECTION" lights Programme guide "SUPER ECO" option button DIMENSIONS With working top Without working top 60 x 85 x 60 120 59,8 x 82 x 57,3 117 Width x Height x Depth (cm) Depth with door
■ When the door is shut, after an audible signal has sounded, the programme will start automatically. The display will show the time remaining to the end of the cycle.
Programme end WARNING! If you open the door during the drying cycle, an audible audio signal advises you that the drying cycle has not yet finished. A 5 second alarm will sound (if not muted) 3 times at 30 second intervals to signal that the programme has ended.
Alarm mute for the PROGRAMME END "DELAY START" button Dishwasher start time can be set with this button, delaying start from 1 to 23 hours. The alarm for the programme end may be muted as follows: Proceed as follows to set a delayed start: IMPORTANT The dishwasher must ALWAYS be off before start of this procedure. ■ Press the "DELAY START" button ("00" will appear on the display). 1.
Memorization of the last programme used 4. Press the same button again ("A1" will appear on the display to indicate that the memorization is on). The last programme used can memorized by following the below: be 5. Turn off the dishwasher by pressing the "ON/OFF" button to confirm the new setting. IMPORTANT The dishwasher must ALWAYS be off before start of this procedure. To disable the memorization, follow the same procedure. 1.
THE WATERBLOCK SYSTEM The waterblock system has been designed to improve the safety of your appliance, particularly when the machine is left unattended. The waterblock system actually prevents flooding which might be caused by a machine malfunction or as a result of a fracture on the pipes.
PROGRAMME GUIDE Wash with prewash For wash programmes with prewash, it is advisable to add a second dose of detergent (max. 10 g) directly in the machine. • /( ) = "AUTOMATIC" PROGRAMMES ARE OPTIMISED THANKS TO THE DIRT SENSOR THAT ADAPTS WASHING PARAMETERS TO DISH DIRT LEVELS. Hygiene+ 75°C An antibacterial cycle, intended for washing and sterilising dishes (even heavily stained ones) babies’ bottles etc. STEAM 75°C Cycle with alternated action of water jets and steam.
N/A = OPTION NOT AVAILABLE * ••••• ••••• ••••• ••••• •••• •••• •••• ••••• •••• ••••• •••• • "SUPER ECO" button "ALL IN 1" button 75°C 140 YES YES YES 75°C 130 YES YES YES 65°C 85 YES YES YES 115/ 125 YES YES YES ( 55 Programme contents Avarage duration in minutes Special function buttons available ( ) 50°C/ ( 60°C ) 100/ 120 YES YES YES ( ) 45°C/ ( 55°C ) 70/ 80 YES YES YES 55°C 240 YES YES YES 45°C 170 YES YES YES 45°C 85 YES YES YES 65°C 59 YES YES YES 50°C 24 YES N/A YES 5 YES
WATER SOFTENER UNIT * The softener unit is set in the factory at level 4 (d4) as this satisfies the requirements of the majority of users. Depending on the source of the supply, water contains varying amounts of limestone and minerals which are deposited on the dishes leaving whitish stains and marks. The higher the level of these minerals present in the water, the harder the water is.
IDENTIFYING MINOR FAULTS Should the dishwasher fail to operate, before contacting the Service Centre, make the following checks: FAULT 1 - Machine completely dead 2 - Machine does not draw water 3 - Machine does not discharge water 4 - Machine discharges water continuously 5 - Spray arms are not heard to rotate 6 - On electronic appliances without a display: one or more indicator lights flashing quickly.
FAULT CAUSE See causes for no.
INDICE pag. pag. pag. pag. pag. pag. pag. pag. pag. pag. pag. pag. pag. pag. pag. pag. pag. pag. pag. pag.
handicap physique, moteur ou mental, et manquant de connaissance sur l’utilisation de l’appareil, si elles sont sous la surveillance d’une personne, donnant des instructions pour une utilisation en toute sécurité de l’appareil. Les enfants ne doivent pas jouer avec l'appareil. Le nettoyage et l’entretien de l’appareil ne doit pas être fait par des enfants sans surveillance d’un adulte.
■ Pour un chargement maximal, veuillez vous référer à la section "DONNÉES TECHNIQUES". ■ L'utilisation de prises multiples et/ou rallonges est déconseillée et dégage le constructeur de toutes responsabilités. ATTENTION! Les couteaux et autres ustensiles avec des parties pointues ou coupantes doivent être rangés avec les pointes en bas ou horizontalement. ■ Ne pas tirer sur le câble d'alimentation de l'appareil pour débrancher la prise du courant.
■ Si vous avez besoin de déplacer la machine après avoir enlevé l'emballage, n’essayez pas de le soulever par le bas de la porte. Ouvrez la porte et soulevez légèrement l'appareil en tenant sur le dessus. Le produit a été conçu et fabriqué en avec les directives Européenne suivantes: ■ ■ ■ ■ ■ Pour l’installation des appareils encastrables, veuillez vous référer au chapitre spécifique ou aux instructions incluses avec le livret.
BRANCHEMENT HYDRAULIQUE 1 IMPORTANT L'appareil doit être relié à l'arrivèe d'eau, exclusivement avec le tuyaux fournis. Ne pas réutiliser les anciens tuyaux. ■ Les tuyaux de vidange et de remplissage peuvent être orientés de façon indifférente vers la droite ou vers la gauche. IMPORTANT Le lave-vaisselle peut-être relié de façon indifférente à l'eau froide ou chaude à condition que la température ne dépasse pas les 60°C.
■ L'extrémité recourbée du tuyau de vidange peut être accrochée au bord d'un évier, mais ne doit pas rester immergée, pour éviter le siphonnage de l'appareil pendant le programme de lavage (fig. 4Y). Raccordement à la vidange ■ Pour la vidange, introduire le tuyau dans l'installation de vidange, en prenant soin de ne pas le plier car l'écoulement des eaux s'en trouverait perturbé (fig. 4).
■ Pour une utilisation optimale de l’appareil, le réservoir à sel, dont la capacité varie de 1,5 à 1,8 kg, doit être rempli de temps en temps en fonction du réglage opéré sur l’adoucisseur d’eau. CHARGEMENT DU SEL ■ L’apparition de taches blanches sur la vaisselle est généralement un signe qui permet savoir que le sel est manquant. ■ Sur le fond de la machine se trouve le bac à sel pour la régénération de l'adoucisseur d'eau.
RÉGLAGE DU PANIER SUPÉRIEUR 1 Quand on utilise habituellement des assiettes de 29 à 32,5 cm de diamètre, charger celles-ci dans le panier inférieur après avoir mis le panier supérieur à sa position la plus haute en procédant comme suit: 1. Faire glisser le panier supérieur vers l’exterieur; 2. Saisir le panier des deux les côtés et le tirer vers le haut (fig. 1).
Un chargement standard journalier est indiqué dans les fig. 1 et 2. CHARGER LA VAISSELLE Panier supérieur (fig. 1) Utilisation du panier supérieur 1 ■ Le panier supérieur est pourvu de supports mobiles accrochés au bord latéral et pouvant occuper 4 positions. ■ Sur la position basse (A-A1) les supports servent pour recevoir les tasses à thé, à café, les couteaux longs et les louches. Aux extrémités des supports, vous pouvez suspendre les verres à pied. A A1 Panier supérieur (fig.
■ Le panier inférieur est doté d’une grille centrale mobile (fig. 3 et 4) qui permet un chargement toujours stable et optimal des assiettes, même quand les dimensions et les formes ne sont pas standards. 5 - POSITION "A": pour le chargement d’assiettes standards ou pour le chargement exclusif de poêles, saladiers etc… - POSITION "B": pour les assiettes de formes particulières même si sont de dimensions standards (assiettes creuses très profondes, assiettes carrées, assiettes sans rebords etc…).
Un chargement standard journalier indiqué dans la fig. 7. Utilisation du troisième panier ■ Le troisième panier à été conçu pour accueillir tous les objets encombrants, comme par exemple les ustensiles petits, long ou plats. En libérant les paniers inférieurs de ces objets, le chargement du lave-vaisselle se fait de manière plus aisée, en permettant par exemple de charger dans le panier du bas à la fois assiettes et casseroles. est Troisième panier (fig.
CHARGEMENT DU PRODUIT DE LAVAGE Le produit de lavage IMPORTANT Il est indispensable d'utiliser de la lessive en poudre, liquide ou en pastilles spécialement destiné aux machines à laver la vaisselle. B Après le versement du détergent dans le bac à lessive, fermer le couvercle, tout d’abord en le glissant vers la gauche (1) puis en appuyant dessus (2) jusqu’à ce que vous entendiez un clic. "CALGONIT" donne les meilleurs résultats de lavage et peut être obtenue facilement.
TYPES DE PRODUITS DE LAVAGE Produits de lavage combinés “Tout en un” Si vous envisagez d’utiliser des produits lessiviels combinés "Tout en un" ("3 en 1"/"4 en 1"/"5 en 1", etc…) par exemple ceux composés de sel et/ou d’ agents de rinçage, nous vous conseillons de: ■ lire attentivement et de suivre les instructions du fabricant, notées sur les emballages; ■ la performance de certains produits lessiviels composés de sel/adoucisseur d’eau dépend de la dureté de votre eau.
CHARGEMENT DU PRODUIT DE RINÇAGE Le produit de rinçage Cet additif qui est introduit automatiquement à la dernière opération de rinçage, assure le séchage rapide de la vaisselle et évite la formation sur celle-ci de taches blanchâtres. C Charger le produit de rinçage A la gauche du bac à lessive se trouve le réservoir du produit de rinçage (fig. A "3"). Pour ouvrir le couvercle, appuyer sur le marquage prévu à cet effet et, en même temps, tirer la languette vers le haut.
NETTOYAGE DES FILTRES Le système de filtrage (fig. A ’’4’’) est constitué par: 1 un réservoir central qui retient les grosses particules; une plaque métallique qui continuellement l’eau de lavage; filtre un micro filtre autonettoyant, situé sous la plaque métallique, qui piège les micro salissures pour garantir un rinçage parfait. ■ Afin d’obtenir d’excellents résultats de lavage dans le temps, les filtres doivent être contrôlés et nettoyés après chaque lavage.
CONSEILS PRATIQUES Que faire pour economiser ■ Au cas où l'on voudrait laver à pleine charge, ranger la vaisselle dans le lave-vaisselle dès que le repas est terminé et en effectuant éventuellement le programme TREMPAGE (ou RINCAGE A FROID) pour ramollir la saleté et éliminer les résidus les plus gros entre chaque charge-ment en attendant d'effectuer le programme de lavage complet.
de laine d'acier. Le lave-vaisselle possède un adoucisseur et il est conseillé l'usage de sel pour éviter la formation de dépôt blanchâtre sur la vaisselle. NETTOYAGE EXTERNE ET ENTRETIEN ■ Pour le nettoyage externe de la machine, ne pas utiliser de détergent ni d’abrasifs mais uniquement un chiffon avec du savon et de l’eau. ■ Le lave-vaisselle ne réclame aucun entretien spécial car la cuve de lavage est autonettoyante.
DESCRIPTION DE LA MACHINE A B C D E F G Touche "MARCHE/ARRÊT" Touche "PROGRAMMES" Touche "DEPART DIFFERE" Touche "START"/"RESET" (départ/annulation programme) AFFICHEUR Touche "ACTION PRO" H I L Touche option "ALL IN 1" M N O Voyants "ACTION PRO" Voyant "MANQUE DE SEL" Voyant "MANQUE DE PRODUIT DE RINÇAGE" Voyants "SÉLECTION D’OPTION" Description des programmes Touche option "SUPER ECO" DIMENSIONS Avec plan de travail Sans plan de travail 60 x 85 x 60 120 59,8 x 82 x 57,3 117 Largeur x Hauteur
SELECTION DES PROGRAMMES ET FONCTIONS SPÉCIALES Programmes “AUTOMATIQUES” Le lave-vaisselle est équipé d’un capteur de saleté, en mesure d’analyser le degré d’opacité de l’eau pendant toutes les phases des programmes "AUTOMATIQUES" (cf. liste programmes). Grâce à ce dispositif, les paramètres du cycle de lavage sont automatiquement adaptés à la quantité réelle de saleté présente sur la vaisselle. En effet le degré d’opacité de l’eau est lié à la quantité de saleté présente sur la vaisselle.
Fin du programme IMPORTANT Vous pouvez interrompre le programme en cours même sans ouvrir la porte, en appuyant sur la touche "MARCHE/ARRÊT". Dans ce cas, pour que le cycle redémarre de l’endroit où il s’est interrompu, il suffit d’appuyer à nouveau sur la touche "MARCHE/ARRÊT". La fin du programme est signalée par un signal acoustique (s’il est activé) de 5 secondes, répété 3 fois toutes les 30 secondes. L’écran et tous les voyants s’éteindront.
Désactivation du signal acoustique de FIN PROGRAMME Touche "DEPART DIFFERE" Cette touche permet de retarder le démarrage du cycle de lavage de 1 à 23 heures. La fonction du signal acoustique à la fin du programme peut être désactivée de la manière suivante: Pour configurer le départ différé, procédez de la mantère suivante: ■ Appuyez sur la touche "DEPART DIFFERE" (l’afficheur montre "00"). IMPORTANT Commencer TOUJOURS la procédure avec le lave-vaisselle éteint.
Mémorisation du dernier programme utilisé 5. Eteindre le lave-vaisselle en appuyant sur la touche "MARCHE/ARRÊT" pour rendre effective la nouvelle configuration. La mémorisation du dernier programme utilisé, peut être activée comme suit: Pour désactiver la mémorisation, suivre la même procédure. IMPORTANT Commencer TOUJOURS la procédure avec le lave-vaisselle éteint.
WATERBLOCK L’intérêt du waterblok est de rendre encore plus sûr votre appareil en particulier en cas de votre absence dans votre appartement. Avec le waterblok sont éliminés tous risques de fuites d’eau et d’innondation provoqués par des anomalies de fonctionnement de la machine, en cas de rupture de tuyaux et plus particulièrement du tuyau d’alimentation d’eau.
LISTE DES PROGRAMMES Lavage précédé d'un prélavage Pour les programmes précédés d'un prélavage, nous vous conseillons de mettre une seconde dose de détergent (max. 10 grammes) directement dans le lave-vaisselle. • /( ) = LE DÉROULEMENT DES PROGRAMMES "AUTOMATIQUES" S’OPTIMISE GRÂCE À L’INTERVENTION DU CAPTEUR DE SALETÉ QUI ADAPTE LES PARAMÈTRES DE LAVAGE EN FONCTION DU DEGRÉ DE SALETÉ DE LA VAISSELLE.
••••• ••••• ••••• ••••• •••• •••• •••• ••••• •••• ••••• •••• • N/A = OPTION NON DISPONIBLE 65°C/ 75°C ( 83 * ) Fonctions facultatives 75°C 140 OUI OUI OUI 75°C 130 OUI OUI OUI 65°C 85 OUI OUI OUI 115/ OUI OUI OUI 125 ( ) 50°C/ ( 60°C ) 100/ OUI OUI OUI 120 ( ) 45°C/ ( 55°C ) 70/ OUI OUI OUI 80 55°C 240 OUI OUI OUI 45°C 170 OUI OUI OUI 45°C 85 OUI OUI OUI 65°C 59 OUI OUI OUI 50°C 24 OUI N/A 5 OUI N/A OUI DE CYCLE.
ADOUCISSEUR D’EAU * L'adoucisseur d'eau est pré réglé en usine sur le niveau 4 (d4) car ce niveau répond à la majorité des besoins. Selon la source d’approvisionnement, l’eau contient des quantités variables de calcaire et de minéraux qui se déposent sur la vaisselle en laissant des taches et des marques blanchâtres. Plus la densité de minéraux dans l’eau est élevée, plus celle-ci est dure.
IDENTIFICATION D’ANOMALIES MINEURES Si votre lave-vaisselle ne fonctionne pas, avant d’appeler votre revendeur faire les contrôles suivants: ANOMALIES 1 - La machine ne fonctionne sur aucun programme CAUSES Prise de courant mal branchée Brancher la prise Touche M/A non appuyée Appuyer sur la touche Pas de courant Contrôler Porte ouverte Fermer la porte Voir causes du N.
ANOMALIES CAUSES REMEDES Voir causes du N.
INHALTSVERZEICHNIS Seite Seite Seite Seite Seite Seite Seite Seite Seite Seite Seite Seite Seite Seite Seite Seite Seite Seite Seite Seite Generelle Sicherheitshinweise Installation Wasseranschluss Einfüllen des Salzes Oberkorb verstellen Geschirr einordnen Informationen für Normtests Spülmittel einfüllen Die verschiedenen Spülmittel Klarspülmittel einfüllen Filterreinigung Praktische Hinweise Wartung und Pflege Beschreibung der Bedienelemente Technische Daten Programmwahl und Sonderfunktionen Waterblock L
Unerfahrenheit oder Unkenntnis nicht in der Lage sind, die Waschmaschine sicher zu bedienen, dürfen die Waschmaschine nicht ohne Aufsicht oder Anweisung durch eine verantwortliche Person benutzen, sich in der Nähe aufhalten oder das Gerät saubermachen. Kinder sollten nicht mit dem Gerät spielen. Reinigung und Benutzerwartung sollten nicht von Kindern ohne Einführung, ausgeführt werden. GENERELLE SICHERHEITSHINWEISE ■ Dieses Gerät ist ausschließlich für den Haushaltsgebrauch konzipiert bzw.
■ Nach der Installation, sollte das Gerät so positioniert sein, dass der Stecker frei zugänglich ist. ■ Den Netzstecker niemals am Kabel aus der Steckdose ziehen, sondern am Stecker selbst. ■ Für die maximale Beladung des Geschirrspülers, beziehen Sie sich bitte auf die Tabelle/den Abschnitt "TECHNISCHE DATEN". ■ Setzen Sie Gerät keinen Witterungseinflüssen (Regen, Sonne usw.) aus. ■ Stützen Sie sich oder setzen Sie sich niemals auf die offene Tür, da das Gerät umkippen könnte.
■ Falls Sie die Maschine nach dem Entfernen der Verpackung bewegen müssen, versuchen Sie nicht, diese an der Unterseite der Tür anzuheben. Öffnen Sie die Tür leicht und heben Sie die Maschine, an der Oberseite. Geräte erfüllen die europäischen Richtlinien: ■ 2006/95/EC (LVD); ■ 2004/108/EC (EMC); ■ 2009/125/EC (ErP); ■ 2011/65/EU (RoHS); sowie die folgenden.
WASSERANSCHLUSS 1 WICHTIG Das Gerät muss an die Wasserversorgung mit neuen Schläuchen angeschlossen werden. Alte Schläuche dürfen nicht wiederverwendet werden. ■ Die Anordunung der Schläuche für den Zu- und Ablauf des Wassers kann wahlweise nach rechts oder links erfolgen. WICHTIG Der Geschirrspüler kann nach Bedarf sowohl an einem Kalt- als auch an einem Warmwasseranschluss angeschlossen werden. Die Temperatur des Warmwassers darf 60°C nicht überschreiten.
■ Das gebogene Schlauchende kann auch am Spülbeckenrand eingehängt werden. Achten Sie darauf, dass der Schlauch nicht im Wasser getaucht wird, um einen Rücklauf des Wassers beim Spülen zu verhindern (Abb. 4 Y). Anschluss an den Wasserablauf ■ Das Schlauchende in dem festen Ablauf befestigen. Der Schlauch darf nicht geknickt werden, damit der Wasserablauf nicht verhindert wird (Abb. 4).
■ Der Behälter faßt ca. 1,5 – 1,8 kg Salz. Um das Gerät effizient zu nutzen, muss der Salzbehälter regelmäßig, je nach Einstellung der Enthärteranlage häufiger oder seltener, nachgefüllt werden. EINFÜLLEN DES SALZES ■ Das Auftreten von weißen Flecken auf Geschirr ist in der Regel ein Warnsignal, dass der Salzbehälter neu aufgefüllt werden muss. ■ Auf dem Geräteboden finden Sie die Öffnung für das Einfüllen des Regeneriersalzes.
EINSTELLUNG DER HÖHE DES OBEREN GESCHIRRKORBES 1 Teller zwischen 29 cm und 32,5 cm Durchmesser werden in den unteren Geschirrkorb eingeordnet. Hierzu muss der Geschirrkorb folgendermaßen bis zur höchsten Position verstellt werden: 1. Den oberen Korb herausziehen; 2. Dann den Korb an beiden Seiten halten und hochziehen (Abb. 1). 2 In dieser Einstellung kann der obere Korb nur mit Geschirr bis 14 cm Durchmesser beladen werden; die klappbaren Geschirrablagen können nicht nach oben geklappt werden.
Eine Standardbeladung für tägliches Spülen ist in den Abb. 1 und 2 dargestellt. EINORDNEN DES GESCHIRRS Beladen des oberen Geschirrkorbes Oberer Geschirrkorb (Abb. 1) 1 ■ Die klappbaren Geschirrablagen des oberen Geschirrkorbes ermöglichen eine flexible Nutzung des Raumangebots. Sie können nach unten oder nach oben geklappt werden. ■ Nach unten geklappt (A-A1), finden Tee- und Kaffeetassen, lange Messer und Schöpfkellen auf ihnen Platz. An den Rändern der Ablage können Kelchgläser eingehängt werden.
■ Der Unterkorb ist mit einem speziellen, umklappbaren Tellergitter ausgestattet, das in der Mitte eingesetzt ist (s. Abb. 3 und 4) und dazu dient, auch Tellern und Geschirrteilen, die nicht den Standardmaßen oder -form entsprechen einen optimalen Halt und Stabilität während des Spülprogramms zu geben. 5 - POSITION "A": wählen Sie, wenn die Geschirrladung aus Tellern mit Standardmaßen oder ausschließlich aus Töpfen, Salatschüsseln usw. besteht.
Ein Beispiel für eine Standardbeladung für tägliches Spülen ist in der Abb. 7 dargestellt. Nutzung des dritten Geschirrkorbs ■ Der dritte Geschirrkorb ist für die Aufnahme von sperrigen Gegenständen konzipiert, wie z.B. besonders kleine Geschirrteile, oder lange und flache Besteckteile. Durch die Entlastung der anderen Körben verbleibt dort mehr Platz für das Einräumen z.B. von Tel-lern und Töpfen zusammen im Unterkorb. Das Einräumen von Platz raubendem Geschirr wird dadurch leichter.
SPÜLMITTEL EINFÜLLEN Das Spülmittel WICHTIG Spülmittel fürs Spülen mit der Hand eignen sich nicht für die Spülmaschine, da wichtige Bestandteile fehlen, die für beste Spülergebnisse notwendig sind. Außerdem beeinträchtigen sie korrekten Betrieb der Spülmaschine. B Nach Einfüllen des Spülmittels in den Behälter bitte den Deckel schließen, indem Sie ihn zuerst zurück über die Öffnung schieben (1) und dann bis zum spürbaren Einrasten herunterdrücken (2).
überflüssig macht, sind die folgenden Hinweise unbedingt zu beachten: DIE VERSCHIEDENEN SPÜLMITTEL Tabs ■ Lesen Sie die Gebrauchshinweise des Spülmittelherstellers sorgfältig durch und wenden Sie das Geschirrspülmittel genau so, wie dort angegeben ist; Spülmittel in Tablettenform von unterschiedlichen Herstellern lösen sich unterschiedlich schnell auf.
KLARSPÜLMITTEL EINFÜLLEN Das Klarspülmittel Das Klarspülmittel erleichtert die Trocknung des Geschirrs und vermeidet die Bildung von Flecken und matten Ablagerungen. Die benötigte Menge des Klarspülers wird beim letzten Spülen automatisch zugegeben, ein voller Behälter reicht für mehrere Male. C Klarspülmittel einfüllen In der Innentür links vom Spülmittelbehälter befindet sich der Klarspülmittelbehälter (Abb. A "3").
FILTERREINIGUNG Das Filtersystem (Abb. A “4”) besteht aus: 1 dem zentralen Filterkorb zum Auffangen von groben Teilchen; der Siebplatte zum ständigen Filtern des Spülwassers; dem Mikrofilter unterhalb der Siebplatte, der auch die kleinsten Schmutzpartikelchen auffängt und so eine optimale Spülung garantiert. ■ Um stets beste Spülergebnisse zu erzielen, ist es ratsam, das Filtersystem vor jeder Benutzung zu kontrollieren und zu reinigen.
PRAKTISCHE HINWEISE Hinweise zum Sparen ■ Um zu sparen, sollte die Spülmaschine immer komplett befüllt werden, bevor gespült wird. Das Geschirr wird jeweils nach dem Essen in die Spülmaschine gefüllt, bis diese voll ist. Eventuell kann zwischen den Beladungen ein Vorspülprogramm durchgeführt werden, um die gröbsten Speisereste einzuweichen und zu entfernen. Hinweise zur Optimierung der Spülergebnisse ■ Um optimale Spülresultate zu erhalten, sind erst die gröbsten Speisereste (z.B.
ÄUßERE REINIGUNG UND PFLEGE 1 ■ Bitte benutzen Sie zur Reinigung des Gerätes von außen stets nur ein feuchtes Tuch und niemals Reinigungsund Scheuermittel. ■ Der Innenbehälter bedarf keiner besonderen Reinigung. 1b ■ Bitte reinigen Sie die Türdichtungen regelmäßig mit einem feuchten Tuch, um evtl. anhaftende Lebensmittelreste und Klarspülerrückstände zu entfernen. ■ Die Geschirrspüler-Reinigung wird empfohlen, um Kalkablagerungen und Schmutz zu entfernen.
BESCHREIBUNG DER BEDIENELEMENTE A B C D E F G Taste "START/STOP" Taste "PROGRAMMWAHL" Taste "STARTVERZÖGERUNG" Taste "START"/"RESET" (Programm starten/löschen) Digitaldisplay Taste "ACTION PRO" H I L Optionstaste “ALL IN 1” M N O Leuchtanzeigen "ACTION PRO" Leuchtanzeige "SALZ EINFÜLLEN" Leuchtanzeige "KLARSPÜLER EINFÜLLEN" Leuchtanzeigen "OPTIONSWAHL" Programmbeschreibung Optionstaste "SUPER ECO" ABMESSUNGEN Mit Arbeitsplatte Ohne Arbeitsplatte 60 x 85 x 60 120 59,8 x 82 x 57,3 117 Breite x Hö
■ Wenn die Tür geschlossen wird, startet das Programm automatisch nach einem akustischen Signal. Das Display zeigt die Restzeit zum Programmende. PROGRAMMWAHL UND SONDERFUNKTIONEN Taste "ACTION PRO" "AUTO" Programme Der Geschirrspüler ist mit einem Trübungssensor ausgestattet, der während der Automatik-Programme (s. Programmlegende) das Wasser permanent prüft und die Waschparameter an die tatsächliche Verschmutzung des Geschirrs anpasst.
Programmende WICHTIG Sie können das laufende Programm auch unterbrechen, ohne die Tür zu öffnen. Drücken Sie hierfür die "START/STOP" Taste. Um das Programm wieder ab dem gleichen Punkt weiter laufen zu lassen, brauchen Sie nur die "START/STOP" Taste erneut zu drücken. Ein akustisches Signal ertönt drei Mal für jeweils fünf Sekunden im 30 Sekunden-Takt (falls nicht ausgestellt). Das Display zeigt die Restzeit zum Programmende.
Akustisches Signal für PROGRAMMENDE ausschalten Taste "STARTVERZÖGERUNG" Die Startzeit des gewählten Reinigungsprogramms kann zwischen 1-23 Stunden verzögert werden. Um das akustische Signal am Programmende auszuschalten, gehen Sie wie folgt vor: Hierzu gehen Sie bitte wie folgt vor: WICHTIG Die Einstellungsprozedur muss IMMER bei ausgeschaltetem Gerät eingeleitet werden. ■ Drücken Sie die Taste "STARTVERZÖGERUNG" (Im Display erscheint die Anzeige "00").
anzuzeigen, dass die Speicherung aktiviert wurde). 5. Schalten Sie den Geschirrspüler durch Drücken der Taste "START/STOP" aus, um Ihre Einstellung zu speichern. Um die Speicherung wieder zu deaktivieren, befolgen sie die gleiche Prozedur. Das zuletzt gewählte Programm speichern Um das zuletzt gewählte Programm zu speichern, gehen Sie wie folgt vor: WICHTIG Die Einstellungsprozedur muss IMMER bei ausgeschaltetem Gerät eingeleitet werden.
WATERBLOCK Das Waterblock-System verhindert einen Wasseraustritt selbst im Störfall und erhöht durch den Schutz vor Wasserschäden die Sicherheit des Spülmaschinenbetriebs. Funktionsweise Das System besteht aus zwei Komponenten: einer Bodenwanne unterhalb des Geräts und einem Sicherheitsventil am Wasserabsperrhahn. Im Falle eines störungsbedingten Wasseraustritts, etwa durch eine Undichtigkeit des Wasserschlauchs, tritt das hydraulisch, d.h.
LISTE DER PROGRAMME Spülen mit Vorspülgang Für alle Programme mit Vorspülgang wird empfohlen, eine zusätzliche Spülmittelmenge (max. 10 Gramm) direkt in den Geschirrspüler zu geben. • /( ) = DE "AUTOMATISKE" PROGRAMMER ER BLEVET OPTIMERET TAKKET VÆRE SNAVSSENSOREN, DER TILPASSER VASKEPARAMETRENE, EFTER HVOR SNAVSEDE TALLERKENERNE ER. Hygiene+ 75°C Programm mit antibakterieller Wirkung, geeignet zum hygienischen Spülen von Geschirr (auch besonders verkrustet), Fläschchen usw.
N.V. = OPTION NICHT VERFÜGBAR * ••••• ••••• ••••• ••••• •••• •••• •••• ••••• •••• ••••• •••• • Taste "STARTVERZÖGERUNG" Taste “SUPER ECO” 75°C 140 JA JA JA 75°C 130 JA JA JA 65°C 85 JA JA JA 115/ 125 JA JA JA ( 111 Programmabläufe Durchschnittliche Programmdauer in Minuten Zusatzfunktionen ( ) 50°C/ ( 60°C ) 110/ JA 120 JA JA ( ) 45°C/ ( 55°C ) 70/ 80 JA JA JA 55°C 240 JA JA JA 45°C 170 JA JA JA 45°C 85 JA JA JA 65°C 59 JA JA JA 50°C 24 JA N.V. JA 5 JA N.V.
WASSERENTHÄRTER * Das Wasser enthält kalkhaltige Salze und Mineralien in je nach Wohngebieten unterschiedlich hoher Menge. Diese Substanzen setzen sich auf dem Geschirr ab und hinterlassen Flecken und weißliche Ablagerungen. Je höher der Anteil dieser Salzverbindungen im Wasser ist, desto höher ist der Härtegrad des Wassers. Ihr Gerät ist mit einer Wasserenthärtungsanlage ausgestattet, die unter Einsatz spezieller regenerierender Spülmaschinensalze “weiches”, d.h.
FEHLERSUCHE Kleine Störungen selbst beheben! Sollte Ihr Geschirrspüler einmal nicht zu Ihrer Zufriedenheit arbeiten, kontrollieren Sie die folgenden Punkte, bevor Sie den Kundendienst rufen: FEHLER 1 - Die Programme funktionieren nicht 2 - Es läuft kein Wasser ein 3 - Das Wasser läuft nicht ab 4 - Wasser läuft ständig ein 5 - Man hört nicht, dass sich die Sprüharme drehen 6 - Bei den elektronischen Geräten ohne Display: Eine oder mehrere LED blinken schnell.
FEHLER GRUND FEHLER -BESEITIGUNG Siehe Gründe 5) Kontrollieren Das Geschirr ist zu dicht angeordnet Geschirr richtig anordnen Das Ende des Ablaufschlauches liegt im Wasser Der Ablaufschlauch darf nicht im Wasser liegen Spülmittel ist nicht richtig dosiert, verklumpt oder hart Dosis erhöhen u. ggf.
Questo elettrodomestico è marcato conformemente alla Direttiva Europea 2012/19/UE sui Rifiuti da Apparecchiature Elettriche ed Elettroniche (RAEE). I RAEE contengono sia sostanze inquinanti (che possono cioè avere un impatto negativo anche molto pesante sull’ambiente) sia materie prime (che possono essere riutilizzate). E’ perciò necessario sottoporre i RAEE ad apposite operazioni di trattamento, per rimuovere e smaltire in modo sicuro le sostanze inquinanti ed estrarre e riciclare le materie prime.
Cet appareil est commercialisé en accord avec la directive européenne 2012/19/EU sur les déchets des équipements électriques et électroniques (DEEE). Les déchets des équipements électriques et électroniques (DEEE) contiennent des substances polluantes (ce qui peut entraîner des conséquences négatives pour l’environnement) et des composants de base (qui peuvent être réutilisés).
La Ditta costruttrice declina ogni responsabilità per eventuali errori di stampa contenuti nel presente libretto. Si riserva inoltre il diritto di apportare le modifiche che si renderanno utili ai propri prodotti senza compromettere le caratteristiche essenziali. Per consultare la scheda tecnica relativa al prodotto, fare riferimento al sito web del produttore. The manufacturer declines all responsibility in the event of any printing mistakes in this booklet.