HOOVER ® Owner's Manual The Easy to Use Deep Cleaner with automatic Review Ultra tool conversion this manual Models These p.22-29 ] ESPANOI. FRAN(_AIS -_4 prig.
Fill in and Retain This HOOVER deep cleaner is designed for deep cleaning carpet, rugs, carpeted stairs and upholstery. The model and serial numbers are located on the data label on the back of the handle. For your personal records, please enter the COMPLETE model and serial numbers in the spaces provided and retain this information.
Grounding Instructions DANGER m Improper connection of the equipmentgrounding conductor can result in the risk of electric shock.
[] A The assembled cleaner will look like this drawing (Ultra mode_ shown). Attach upper handle _1_ Remove clean solution tank (upper tank) from deep cleaner _1 With cord hook (A) to back of deep cleaner, push upper handle down onto lower handle. Push bolts into holes on front of handle. If bolts will not go through hole easily handle is not pushed completely down. [] D Place nuts in recessed areas on back of handle.
[] Attach []Remove rack hose rack tool and taped screw from Insert projections back of cleaner. I_1 Slide rack down into place. Insert screw at (D) and tighten with a Phillips screwdriver Storing hose & tools Store hose on rack by first positiong hose in front section of clip on rack into slots on l_Then continue wrapping hose as shown snapping end of hose connector into clip. For Plus* or Ultra** models I_The powered hand tool** is shipped in a plastic bag for protection.
Theassembled deepcleaner willlooklikethedrawing [] [] 1. 2. _5 : 22 1 20 17 19 Hand grip Solution trigger: press to release clean solution. 3. Cord clip: place cord in clip to keep it out of the way when using cleaner 4. Hose 5. Hose holders: wrap hose around holders for storage 6. Cord hooks: wrap cord around hooks for storage. The top hook can be rotated right or left for quick and easy cord release. 7. Stair/upholstery nozzle* OR Powered hand tool** 8. Carrying handle 9.
_E / []The deepcleaner mayalsobeliftedbyplacinga handunderthe uppercleansolution tankhandleas shown Automatic "shut off" []When the recovery tank (lower tank) is ful! the automatic shutoff mechanism will shut off the deep cleaner suction (suclion will be noticeably reduced). At that time the red float disk will rise to the top of the recovery tank lid (E) The deep cleaner will no longer pick up dirty solution and the motor sound will become noticeably higher in pitch.
5 OUNCES/ Using cap, measure detergent following the chart below. For carpet, carpeted stairs and upholstew: Fill cap to fill line (5 ounces) with HOOVER Carpet/Upholstery Detergent. For bare floors: I.' Fill cap to fill line (5 ounces) with HOOVER Bare Floor Cleaner ) Do not use Bare Floor Cleaner on carpet or upholstery. Do not use any type of wax with your 'SteamVac' deep cleaner. []Rotate tank cap counterclockwise and lift up to remove cap []Turn cap (A) upside down to serve as a measuring cup.
For full suction, it is important that the recovery tank lid is properly secured before cleaning. _UNLOCK ¢ Raise tank handle to carrying position to place it into base of cleaner. Move handie completely forward to leek tank into place (see Fig 35) []Raise handle to carrying position (straight up) to unlock tank from base of deep cleaner Lift tank from deep cleaner and carry it to a sink or drain.
To clean the outside of the machine, wipe off dirt with a cloth dampened in warm water and mild detergent. Do not use solvent or petroleum based products to clean the machine. vent streaking Keep nozzle flat on floor for both forward and reverse strokes. Read "Before you begin cleaning" instructions on page 9. It is best to alternate wet and dry strokes as described above. Fill clean solution tank (upper tank) with HOOVER Carpet/Upholstery Detergent according to instructions on pages 7 and 8.
Dry hands and plug deep cleaner into a properly grounded outlet. Step on handle re_ease pedat and tower handle to operating position; turn deep cleaner ON. To release solution, press trigger. Slowly move deep cleaner forward and backward over area to be cleaned. To pick up dirty solution, release trigger and slowly move deep cleaner over area where solution has just been dispersed. Use both forward and reverse strokes.
When finished cleaning, follow "After cleaning" instructions on page 9 and "After using tool" instructions on page 11. Read "Before you begin cleaning" Instructions on page 9. _\ f-- mL_tl and position it against riser. Itool, tool slowly over carpet without pressing trigger (dry stroke) It is best to alternate wet and dry strokes as described above End with more dry strokes to aid in faster drying of carpet Overlap strokes by 1/2 inch to help prevent streaking.
If you have problem Full One Year a If a minor problem occurs it usually can be solved quite easily when the cause is found by using the check list below Possible cause Possible solution • Not firmly plugged in • Plug unit in hrmly • No voltage In wall plug • Check fuse or breaker • Blown fuse/tripped breaker • Replace fuse/reset breaker Possible cause Possible solution • Blockage In tool on end of hose • Remove tool and clear blockage 1. Hoover Factory Service Centers 2.
lib HOOVER y _ son marcas registradas THE HOOVER COMPANY, NORTH CANTON, OHIO 44720 HOOVER et _ sent des marques d_pos_es THE HOOVER COMPANY, NORTH CANTON, OHIO 44720 HOOVER and _ are registered trademarks THE HOOVER COMPANY, NORTH CANTON, OHIO 44720 R3 2-98 F5865-167"168-169-171-173-181-183-184-185-900 Lithe USA 56518-095