HOOVER ate TM SpinS 800 Floor Cleaner www_h@overoco_
When using an electrical appliance, ahvays ibBow basic precautions. including the following: READ ALL INSTRUCTIONS BEFORE USING APPLIANCE. _lb reduce the risk A B of fire. electric shock, or injury: , Use indoors only. , Use only on surfaces moistened by the cleaning process or small spills. Do not immerse product. • Connect to a p_roperlygrounded outlet only. See ' Grounding Instructio_ls'. - Do not clean over floor electrical outlets. * For use on bare floors or seated wood floors.
T0-7ontact u--s: -" - www.hoover.com . 1-800-944-9200 - automated Important safeguards ........ Carton contents ............. Cleaner description .......... service 2 3 4 dealer locator - 1-330-499-9499 - our Consumer Response Center {8AM to 5 PM Monday - Friday) General Operation Mode selector dial .......... Solution tank ........... f Fill in and Save 8 9-10 To clean filters ......... 11-12 How to clean Recommended cleaning sequence ................. 12 Cleaning floors ...........
f This cleaner is intended household use. for Operate cleaner only at voltage specified on data plate on back of cleaner, Plug cleaner into a properly grounded outlet, 11 11j \ 1. 2. 3. 14 13 Soft hand grip ON/OFF switch Solution trigger: squeeze to release cleaning solution 4. Mode selector dial: turns brushes ON for wet cleaning and OFF for wet pickup and dry vacuuming 5. Clean solution tank cap/measuring cup 6. Clean solution tank 7. Clean solution tank release 8. Recovery tank release 9.
Assemble handle Rotate bottom the upright %lt. Align handle aandle handle position support (A) up until a snap is control rod (B) on upper (C) with slot in bottom support (D). Push upper is snapped handle in place. (C) down until it / Install brushes To install brushes, pright position. that it rests on the and nozzle place handle in Tilt cleaner back so floor. Align post (A) on brush block with hole (B) on bottom of cleaner. Turn brushes slightly until post fits easily into hole. \ Con
Press place. brush % install assembly nozzle, Align middle section (E) or] cleaner. Remove cardboard area on underside While The holding inward make firmly sure to snap latches (D) of nozzle packing of nozzle. insert into (C) are with opening from squeegee nozzle in place, to lock in place. slide two sections (A & B) of the tool y snap together for assembly. Press where indicated securely in place.
Store hose;tools and accessories H F To store bose: Place the hose grip (D) into (E) on back of caddy. Pull hose up and press into cut-out area (F). Continue wrapping hose down, underneath tongue (G), and back tap, pressing into second cut-out area (H). Place hose end (I) into slot (J) on back of caddy. E G Place floor swivel tool (K), grout tool (L), brush assembly (M), telescoping wand (N) and detergent (0) into caddy as shown. Raise tapper handle (A) to upright position until it locks in place.
To move your cleaner from room to room, put handle in upright position, tilt cleaner back on rear wheels and push forward. The cleaner may also be lifted using the carying handle (A) on the ff'ont of the cleaner. Your HOOVER FloorMate TM SpinScrub TM 800 Cleaner can be used to both vacuum dry debris and wet clean non-carpeted floor surfaces such as vinyl, tile, marble and sealed wood. It is not intended for use on carpet or rugs.
The tanks Solution (upper) tank The solution tank holds detergent and water dispersed onto the surface being cleaned. that is to be How to fill Disconnect Place cleaner cleaner fl'om electrical handle in upright, 75 remove tank, ht out. Carry squeeze outlet. locked release position. button and pulltank tank to a sink. Rotate (A). tank cap counter-clockwise Turn cap (A) upside down to serve and lift up to remove as a measuring cap cup.
If rubber ring (D) on cap has become dislodged, reposiit with uneven side against ledge (E) as shown. J Replace cap. Rotate must be locked and to prevent leaking. Slide tank place. straight Recovery (lower) Automatic shut-off cap clockwise until in place for proper into position until it locks in place. performance latch snaps the recovery in tank An automatic suction shut-off tank to prevent the tank from is built into overflowing.
How to empty "x Turn cleaner off and disconnect from electrical outlet. Although not necessary for satisfacto_\y performance, it is recommended that the recovery tank be emptied after dry vacuuming and before wet operation. Check the solution tank also. It may need to be refilled at this time. To remove tank, press pull tank straight J Remove down out. on release tank lid (C). Empty button (B) tank. .
Dry or loose debris in the tank lid. will also collect on the filter screen To remove debris from screen, remove the pleated the lid. Remove debris from screen (D). The filter screen running water. may also be cleaned by rinsing \ filter it under Reposition pleated filter in lid. Replace lid onto pressing down firmly until snapped in place. To replace recovery ledge (E) and push locked in place.
NOTE: Your HOOVER€) FloorMate TM SpinScrub T< 800 cleaner may be used to clean that have been sealed with a polyurethane coating and can be cleaned with water. wood CAUTION: cleaning To prevent damage to wood floors, follow the flooring manufacturer's floors rec- If using cleaner on sealed wood floors, inspect floor surface for worn finish, bare wood or separated joints. Do not use FloorMate TM SpinScrub TM cleaner to wet clean sealed wood floors if any of these conditions exist.
Select tool A. Floor swivel tool * Swivel head * 2 rows B. of brushes o Use to clean Grout tool small, * Stiff brushes on stubborn tight areas to use for more, grout stains concentrated cleaning k,. Attach Unplug hose cleaner and tool from How to connect /Open / / hose Align Insert hose hose Close How hose outlet. hose door (A) on side connector connector / To disconnect connector. Remove / electrical of cleaner.
oThe get handle cleaning Using / ,/ the Squeeze cleaning Turn storing cleaner and hold solution. "h in order ) trigger and pull without (A) in hose grip tool over same area putting down more to release to pick solution. cleaner: OFF and disconnect Empty dry. • Press on upper storage. handle • Make nothing • Do not store sure rinse and • completely- position hose.
Cleaning the nozzle Turn cleaner OFF and disconnec{ The cleaner's nozzle can be removed Slide the two nozzle release from electrical for easy cleaning. latches (A) outward. Remove nozzle (B) by pulling straight out. Rinse nozzle under running water. Remove tueegee (C) and wipe with a damp cloth. To outlet. debris from nozzle, make sure latches (D) are out. should be in the upright bly of the nozzle. position Align middle section (E) of nozzle with opening for easier" assem- i \ (F)
Cleaning the brushes The brush assembly Turn cleaner can be removed OFF and disconnect Place handle in the upright for easy cleaning. from electrical outlet. position. Remove tanks to pr>vent leaking. Set aside. Pull the two nozzle release buttons (A) out. Remove nozzle. B Tilt cleaner" back so handle Push two brush r assembly. rests on floor. release buttons (B) and remove The brushes can be washed with a mild not use a solvent based detergent. detergent the brush and rinsed.
Use the list below to help solve minor problems. ,/Make sure the cleaner plugged in firmly. C]eaner won't run Low suction is / Check the fuse or breaker. V"Empty andthe the recovery tank; it may be full automatic shut-off engaged. ¢" Make sure filter and filter" lid are properly positioned. ,/Make sure tanks ¢" Check are locked the filter" and clean if dirty. ,/Make sure nozzle and locked.
Lubrication The motor is equipped with bearings which contain sufficient lubrication for the life of the motor. The addition of lubricant could cause damage. Do not add lubricant to motor bearings.
Full One Year Warranty (Domestic Use) Your HOOVER(,'_ appliance is warranted in normal household use, in accordance with the Owner's Manual against original defects in material and workmanship fbr a period of one fidl year fl'om date of purchase. This warranty provides, at no cost to you, all labor and parts to place this appliance in correct operating condition during the warranted period.
