HGM600X/1,HGM610NX/1 Cooker Hood Instruction Manual ENGLISH(EN)--------------------------------------------------------------- page 001
Cooker Hood Instruction Manual 1
Content 1…………………………………..………………………………Safety instructions 2…………………………………..………………………………Installation 3…………………………………..………………………………Start using your cooker hood 4…………………………………..………………………………Troubleshooting 5…………………………………..………………………………Maintenance and cleaning 6…………………………………..
SAFETY INSTRUCTIONS This manual explains the proper installation and use of your cooker hood, please read it carefully before using even if you are familiar with the product. The manual should be kept in a safe place for future reference.
Always to do: ●Always put lids on pots and pans when cooking on a gas cooker. ●W hen in extraction mode, air in the room is being removed by the cooker hood. Please make sure that proper ventilation measures are being observed. The cooker hood removes odours from room but not steam. ●There shall be adequate ventilation of the room when the cooker hood is used at the same time as appliances burning gas or other fuels. ●Cooker hood is for domestic use only.
INSTALLATION (VENT OUTSIDE) MOUNTING OF THE V-FLAP If the cooker hood does not have an assembled V-flap 1, you should mount the halfparts to its body.The images only show an example of how to mount the V-flap, because the outlet may vary according to different models and configurations. To mount the V-flap 1 you should: • Mount two half-parts 2 into the body 6; • the pin 3 should be top oriented; • the axis 4 should be inserted into the holes 5 on the body; • repeat all the operations for the 2nd half-part.
3. Install the hook on a suitable place once the installation height is fixed, and keep it in line. The fixed position of the inside chimney bracket is the place of chimney. See pic 2. 4. Attach the converter and expansion pipe, and fix the pipe on the converter with a cable tie. Then put the cooker hood on the hook. See pic 3. Note:The expansion pipe is not included in the product. 5. After adjust the height,fix the body with 2 pcs ST4*30mm safety screws.
Electrical Installation All installation must be carried out by a competent person or qualified electrician. Before connecting the mains supply ensure that the mains voltage corresponds to the voltage on the rating plate. Direct Connection The appliance must be connected directly to the mains using an omnipolar circuit breaker with a minimum opening of 3mm between the contacts. The installer must ensure that the correct electrical connection has been made and that it complies with the wiring diagram.
•After the installation ,make sure that the cooker hood is level to avoid grease collection at on end. •Ensure the expansion pipe selected for installation complies with relevant standards and is fire retardant. WARNING: For safety reason, please use only the same size of fixing or mounting screws which are recommended in this instruction manual. Failure to install the screws or fixing device in accordance with these instructions may result in electrical hazards.
works at low speed. Indicator light of low speed will be bright. Press power button again to close it, and its indicator light will be off. All the function operation of the hood will be closed, the hood enters into standby mode, and run by circle. The speed buttons and lamp button can work separately and not controlled by the power button. When a certain function button is pressed, the hood operates at that function status.
Lights not working Insufficient suction The Cooker hood inclines Leakage from the connection of chimney and cover Take chimney down and seal. Broken or faulty bulbs Replace bulbs as per this instruction. The distance between the cooker hood and the gas top is too far The fixing screw is not tight enough Refit the cooker hood to the correct distance. Tighten the hanging screw and make it horizontal. NOTE: Any electrical repairs to this appliance must conform to your local, state and federal laws.
voidmanufactures warrantee. GREASE MESH FILTERS The mesh filters can be cleaned by hand.Soak them for about 3 minute in water with a mild detergent and then brush it gently with a soft brush. Do not apply too much pressure so as to avoid any damage to it . (Leave to dry naturally out of direct sun light) Filters should be washed separately to crockery andkitchen utensils. It is advisable not to use rinse aid.
NOTE: • • Make sure the filter is securely locked. Otherwise, it would loosen and cause danger. When activated carbon filter attached, the suction power will be lowered. BULB REPLACEMENT Important : The bulb must be replaced by the manufacturer, its service agent or similarly qualified persons. Always switch off the electricity supply before carrying out any operations on the appliance. When handling bulb, make sure it has completely cooleddown before any direct contact with hands.
ENVIRONMENTAL PROTECTION: This appliance is labelled in accordance with European Directive 2012/19/EU on Waste Electrical and Electronic Equipment Regulations 2013 regarding electric and electronic appliances (WEEE). The WEEE contain both polluting substances (that can have a negative effect on the environment) and base elements (that can be reused). It is important that the WEEE undergo specific treatments to correctly remove and dispose of the pollutants and recover all the materials.
