Owner’s Manual Operating and Servicing Instructions ® WindtunnelTM Cyclonic U57809RM REMANUFACTURED Review this manual before operating the cleaner. www.hoover.com ÿ2008 All rights reserved. #17-01-58-058-00-H301 #59881086.
Thank you for choosing a HOOVER® product. Please enter the complete model and serial numbers in the spaces provided. Model ______________________________ Hint: Attach your sales receipt to this owner’s manual. Verification of date of purchase may be required for warranty service of your HOOVER product. HOUSEHOLD TYPE/TYPE MENAGER/TIPO DOMESTICO SERIAL NO./NUMERO SER.
Important Safety Instructions When using an electrical appliance, always follow basic precautions, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE WARNING: To reduce the risk of fire, electric shock, or injury: • Do not use outdoors or on wet surfaces. • Close supervision is necessary when any appliance is used by or near children. Do not allow vacuum cleaner to be used as a toy or to run unattended at any time.
1. CLEANER ASSEMBLY Carton contents 1-1 A. B. C. D. A D B Handle section Cleaner base and upper housing assembly Cleaning tools and wands Powered Hand Tool Remove all parts from carton and identify each item shown. Make sure all parts are located before disposing of packing materials. C Attach handle 1-3 1-2 1-4 A Using a Phillips screwdriver, remove (2) screws from the top of the upper housing assembly. Insert handle section (A) into upper housing assembly.
2. HOW TO USE Cleaner Description 1. 2. 3. 4. 5. 6. 7. 8. 9. Soft TouchTM handle grip ON/OFF switch Hose Dirt cup release button Dirt cup assembly Hose handle Cord reel window Headlight Nozzle control knob: turn knob to correct setting for height of carpet being cleaned. 10. Furniture guard: helps prevent cleaner from marking furniture. 11. Agitator brush roll shut-off pedal 12. Agitator brush roll shut-off indicator 13. Final filter access 14. Combination tool 15. Powered hand tool 16.
Cord Rewind 2-4 Grasp the end of the plug and pull to release cord from cord reel. After desired cord length is reached, the cord will lock into position. A To return cord for storage, hold plug and press on button (A) at top of cord reel. To prevent cord from whipping, hold plug until cord is rewound. Transporting Cleaner 2-5 To move your cleaner from room to room, put handle in upright position, tilt cleaner back on rear wheels and push forward.
3. CLEANING TOOLS Tools allow for cleaning surfaces above the floor and for reaching hard to clean areas. The cleaner is ready for tool use when handle is in upright position. The agitator brush roll will not rotate when the cleaner is in the upright position or the if the agitator brush roll shut off indicator is in the OFF position when the handle is lowered. Removing Hose When using 3-1 cleaning tools, place cleaner handle in the upright position.
Stair Cleaning Use the hose and powered hand tool for stair cleaning. Clean from bottom to top. CAUTION: To avoid personal injury or unnecessary wear to carpet, and to prevent the cleaner from falling, always place it at bottom of stairs. Extra Reach™ Hose (available at additional cost) Turn cleaner OFF before disconnecting and connecting hose. Remove hose end from dirt duct (A). Align end of Extra Reach™ hose with projections (B) over slots on dirt duct (C).
Dirt Cup (cont.) How to Empty 4-2 4-3 A A Press dirt cup release button (A) and pivot cup out. B Holding dirt cup over trash receptacle, press dirt cup door release button (A) to open dirt cup door (B). Close door and press dirt cup door release button to latch dirt cup door closed. Place bottom of dirt cup into cleaner body first. Pivot cup into cleaner body. 4-4 4-5 Press on dirt cup release button while firmly pressing on dirt cup.
Filters (cont.) Secondary Filter: How to Clean Disconnect cleaner from electrical outlet. Do not use cleaner without dirt cup or filters in place. Remove dirt cup as described in Fig. 4-2. 4-8 With thumb and forefinger, slide latch (A) located at the top of the housing to the right and pull down to remove gray filter frame. Remove black foam filter. Rinse filter frame cartridge and foam filter under cold water.
Belts Disconnect cleaner from electrical outlet. WARNING: Agitator brush roll can start suddenly. Unplug cleaner before turning it over. The belts are located under the bottom plate of the cleaner and should be checked from time to time to be sure they are in good condition. Replacing Flat Belt Replace belt if it is stretched, cut or broken. To check the flat belt, refer to Fig. 4-13.
Agitator Brush Roll Disconnect cleaner from electrical outlet. WARNING: Agitator brush roll can start suddenly. Unplug cleaner before turning it over. Replacing Agitator Brush Roll When agitator brushes are worn, the brush roll should be replaced. Removing Agitator Brush Roll Inspecting Agitator Brush Roll 4-19 To check condition of brushes, move edge of a card across bottom plate while turning agitator brush roll.
Powered Hand Tool (cont.) Replacing Agitator Brush Roll How to Replace 4-25 B A Remove agitator including end plates (A) and discard. 4-26 Inspect belt to ensure that it is in good condition. If belt is cracked, gouged or broken, replace it (see following section). A Insert brush roll through belt and position belt over gear teeth (B) on brush roll. 4-28 4-27 B With curved ends down, slide end plates (A) of brush roll into slots (B) on tool.
Lubrication Service The motor is equipped with bearings that contain sufficient lubrication for the life of the motor. The addition of lubricant could cause damage. Therefore, do not add lubricant to motor bearings.
5. TROUBLESHOOTING PROBLEM POSSIBLE REASON POSSIBLE SOLUTION Cleaner won’t run 1. Power cord not firmly plugged into outlet. 1. Plug unit in firmly. 2. Blown fuse or tripped breaker. 2. Check fuse or breaker in home. Replace fuse/ reset breaker. 4. Thermal Protector activated. 4. Unplug and allow cleaner to cool for 30 minutes. (This willl reset the thermal protector) 1. Blockage in air flow passages. 1. Clear blockage - Pg. 16. 2. Dirt cup full. 2. Empty dirt cup - Pg. 9. 3.
Clearing Blockages Disconnect cleaner from electrical outlet. Low suction or pick up may be due to a blockage in the system. Refer to the following steps to check for blockages continuing with each step until the blockage is found: Fullness of Dirt Cup 5-1 Check Airflow Path Check Secondary Filter 5-2 5-3 A Check fullness of dirt cup; empty if needed B Plug cleaner in and turn ON. Check for suction at end of hose (A). If there is suction turn cleaner OFF and unplug.
✃ Parts and Accessories MAIL ORDER FORM Detach this section and mail to: The Hoover Company 7005 Cochran Road • Glenwillow, Ohio • 44139 Attn: Sales & Service Center Item Description Part No. Qty/ Pk. HEPA Final Filter 93002360 1 $ 8.99 Secondary filter cartridge 93002517 1 $ 6.99 Price/Pk. Foam filter (secondary filter) 93002518 2 $ 3.99 Headlight 27313-107 1 $ 2.49 Flat Belt 40201-271 2 $ 3.99 V-Belt 40201-200 2 $ 4.99 Qty.
Parts and Accessories RETAIN THIS SECTION FOR YOUR RECORDS Item Description Part No. Qty/Pk. HEPA Final Filter 93002360 1 $ 8.99 Secondary filter cartridge 93002517 1 $ 6.99 Foam filter (secondary filter) 93002518 2 $ 3.99 Headlight 27313-107 1 $ 2.49 Flat Belt 40201-271 2 $ 3.99 V-Belt 40201-200 2 $ 4.99 Total Price/Pk. Qty. TOTAL MERCHANDISE $ APPLICABLE STATE TAX + $ SHIPPING & HANLDING + $ 7.