User Manual

ManualsBrandsHopkins Towing Solutions ManualsCar & Vehicle ElectronicsHopkins 50002 Smart Hitch Backup Camera System

ONE YEAR LIMITED WARRANTY: Subject to the limitations and

exclusions set forth in the Limited Warranty, Smart Hitch Camera/Sensor

System is warranted by Hopkins Manufacturing Corporation against

defects in material or workmanship that result in a product failure during

the one year period following the date of purchase. This Limited Warranty

applies only to claims made by the original end user (hereinafter “you”)

and cannot be assigned, transferred or conveyed to any subsequent

users.

EXCLUSIONS FROM COVERAGE: This warranty does not apply to any

claims arising from misuse, abuse, unauthorized repair or alteration,

circumstances where Smart Hitch Camera/Sensor System is improperly

installed or improperly wired contrary to Smart Hitch Camera/Sensor

System instructions; or damage or defect attributable to ﬁre or other

casualty, including, without limitations, acts of God or exposure to

abrasive or corrosive materials or pollutants, or attributable to collision or

other accidents involving vehicles upon which the Smart Hitch Camera/

Sensor System is installed.

LIMITATIONS: Hopkins Manufacturing Corporation expressly limits the

applicability of the implied warranty of merchantability and the implied

warranty of ﬁtness for a particular purpose to the one-year warranty as

provided herein. Some states do not allow limitations on how long an

implied warranty lasts, so the above limitation may not apply.

To the extent permitted by state law, the remedy of repair or replacement

discussed below is the sole remedy available to the end user under this

Limited Warranty. THIS LIMITED WARRANTY SPECIFICALLY EXCLUDES ALL

INCIDENTAL, SPECIAL, OR CONSEQUENTIAL DAMAGES SOME STATES

DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR

CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION

MAY NOT APPLY TO YOU. To the extent permitted by state law, Hopkins

Manufacturing Corporation liability for Smart Hitch Camera/Sensor System

will not exceed the purchase price paid for the product.

NOTICE: This warranty gives you speciﬁc legal rights, and you may also

have other rights, which vary from state to state.

IMPORTANT NOTE: Please check with you local and state laws to ensure

by covering up part of the license plate is not a violation to the law.

Hopkins Manufacturing takes not responsibility for paying any type of ﬁne

or ticket associated with this product.

EXCLUSIVE AGREEMENT: To the extent permitted by state law, this

one-year limited warranty is a complete and exclusive statement of the

warranties, which apply to the Smart Hitch Camera/Sensor System; there

are no express or implied warranties beyond those expressly stated

above. No employee, agent, dealer or other person is authorized to give

any warranties on behalf of Hopkins Manufacturing Corporation, except as

authorized in writing.

STATUE OF LIMITATIONS: To the extent permitted by state law, in

purchasing the Smart Hitch Camera/Sensor System you agree that any

action for breach of contract or warranty must be commenced within one

year after the cause of action has occurred.

PROCEDURE: In the event that a product failure covered by this

warranty occurs while this warranty is still valid, Hopkins Manufacturing

Corporation will, at its option, either: (a) repair the defective unit; (b)

replace the defective unit with a new unit; or (c) replace the defective

unit with a refurbished unit. Hopkins Manufacturing Corporation will ship

your repaired, new, or refurbished unit to you without charge for parts,

service, or any other cost (except shipping and handling) incurred by

Hopkins Manufacturing Corporation or its representatives in connection

with the performance of the warranty. Failed units covered under this

warranty must be sent by you to Hopkins Manufacturing Corporation with

shipping prepaid by you. You are responsible for all cost incurred in the

removal, reinstallation, and shipping of the unit. A copy of the sales slip

received by you at the point of purchase of the unit must accompany the

returned unit. Call Hopkins Manufacturing Corporation for Warranty Return

Authorization.

For Warranty return Authorization

Call: Hopkins Manufacturing Corporation

Toll Free: (800) 835-0129

WARRANTY INFORMATION

HOW THE MONITOR WORKS

Sound Volume

1) The volume can be turned up or down by

pressing the side button “up” or “down”.

There are 4 volume levels (Mute, Low,

Medium, High)

17.7 – 23.6 in (45–60 cm) 2 1 1

23.6 – 29.5 in ( 60–75 cm) 3 2 1

29.5 – 37.4 in (75–95 cm) 4 3 3

> 37.4 in (95 cm) 5 4 4

Height

License plate angles

Connect wire from main bracket to the

wire coming from the monitor

STEP 3. Connect the cables and secure the monitor

1) Connect wire from mounting bracket (C) to the wire coming from the monitor (A). This will provide power to the camera

and sensors. Hide wire where convenient depending on vehicle type.

2) Place monitor (A) in desired location. Remove backing from foam tape and press down ﬁrmly to ensure the monitor is

secure.

STEP 4. Positioning the adjustable sensors and camera

Everyday Mode:

SmartZone

™

Sensing:

Green - 3.5 feet to 5.5 feet

Yellow - 1.5 feet to 3.5 feet

Red - 0 to 1.5 feet

5) Insert grommet (G) into the hole to protect the wire. Feed the wire from the bracket (C) through the hole.

6) Install the main bracket (C) with license plate to the back of your vehicle using license plate screws (F) included in the

package. These screws are longer than standard license plate screws to help provide support and better attach the

system to the vehicle.

Secure license plate bracket with

provided screws

1) Measure from ground to the center line of the sensor. For an accurate measurement ensure your vehicle is on a level

surface.

Identify the angle of your license plate. Stand to the side of your vehicle and see if the top of your license plate is angled

(Backward, Flat, Forward).

Based off your sensor height from the ground and angle of licence plate, adjust the sensor setting according to the chart

below. Adjust each sensor to the appropriate setting and tighten screws. Default setting for the sensors is setting 3.

For camera (B), adjust the angle up/down to create maximum visibility behind your vehicle.

)

To ensure the sensors and camera are working correctly, slowly back toward a stationary object.

Hitch Mode:

Simply press “IN” on the side button and

press up or down on the button to activate

hitch mode from “OFF” to “ON”. Repeat

process to go back to Everyday Mode.