Andes6 Andes8 ELLIPTICAL OWNER’S MANUAL Read the elliptical guide before using this owner’s manual.
ASSEMBLY WARNING There are several areas during the assembly process that special attention must be paid. It is very important to follow the assembly instructions correctly and to make sure all parts are firmly tightened. If the assembly instructions are not followed correctly, the elliptical could have frame parts that are not tightened and will seem loose and may cause irritating noises. To prevent damage to the elliptical, the assembly instructions must be reviewed and corrective actions should be taken.
PARTS INCLUDED: UPPER HANDLEBAR CONSOLE Andes6 Andes8 TOUCH PAD PANEL AND DISPLAY WINDOWS FF FF FF FF FF 1 Main Frame 2 Upper Handlebars Set 1 Console Mast Set 1 Console Box 1 Parts Box PULSE GRIPS FRONT / REAR CONSOLE MAST COVER UPPER HANDLEBAR COVER LOWER HANDLEBAR PEDAL ARM FOOTPAD ROLLER WHEEL COVERS CRANK COVER POWER CORD SOCKET PRE ASSEMBLY UNPACKING Unpack the product where you will be using it. Place the elliptical carton on a level flat surface.
ASSEMBLY STEP 1 ASSEMBLY STEP 2 PRE-ATTACHED HARDWARE PARTS: CONSOLE MAST PRE-ATTACHED HARDWARE PARTS: CONSOLE Andes6 Andes8 SCREW (A) M8 x 1.25P x 16 L Qty: 4 WASHER (A) φ8.4 xφ17.0 x 1.0T Qty: 4 SCREW (B) M4 x 0.75P x 12L Qty: 2 SCREW (C) M5 x 0.8P x 12L Qty: 4 HEXAGON L WRENCH #5 (W/SCREW DRIVER) Andes6 Andes8 HEXAGON L WRENCH #5 (W/SCREW DRIVER) SCREW(B) A Use HEXAGON L WRENCH #5 to remove PRE-attached WASHERs (A) & SCREWS (A) from frame. B Put CONSOLE WIRES through CONSOLE MAST.
ASSEMBLY STEP 3 PRE-ATTACHED HARDWARE PARTS: Andes6 Andes8 SCREW (D) M10 x1.5P x 10L Qty: 4 UPPER HANDLEBARS A Use HEXAGON L WRENCH #5 to remove PRE-ATTACHED SCREWS (D) from UPPER HANDLEBARS. B Attach UPPER HANDLEBARS to LOWER HANDLEBARS with PRE-ATTACHED SCREWS (D).
Andes6 Andes8 Folding Instruction FOLDING INSTRUCTION FOLD DOWN INSTRUCTION Use right hand to grip the handle, push forward gently. Pull up on the handle to release. Pull back to fold down. FOLD UP INSTRUCTION Use right hand to grip the handle. Pull up until guide rail set locks into place. Andes6 Andes8 HANDLE HANDLE SUPPORT TUBE SUPPORT TUBE HANDLE SUPPORT TUBE HANDLE SUPPORT TUBE NOTE: The guide rails have a soft drop shock system. Let the rails unfold, do not push down on the rails.
MOVING the elliptical ELLIPTICAL OPERATION Andes6 Andes8 This section explains how to use your elliptical’s console and programming. The BASIC OPERATION section in the elliptical guide has instructions for the following: • LOCATION OF THE Elliptical • POWER/GROUNDING INStRUCTIONS • FOOT POSITIONING • MOVING the elliptical • LEVELING the elliptical • POWER/MANUAL INCLINE OPERATION • Using the HEART RATE function Warning! Our ellipticals are heavy, use care and additional help if necessary when moving.
CONTROLS Click ANDES 6 & 8 CONSOLE OPERATION 3 seconds hold 5 seconds hold • Increase • Next item Andes6 Andes8 • Decrease • Previous item • • • • 符 14 Quick start Select item Start the workout Enter to the next step • Stop the workout • Back to the previous step • Finish inputting user ’s name • Reset • Language selection • Metric /British selection QUICK START 1) Make sure the power is on. 2) Simply press the “START” key and begin exercising.
PROGRAM PROFILES • Manual: Allows you to adjust the resistance level to your preference, without a preset program. • Intervals: Improves your strength, speed, and endurance by raising and lowering the resistance levels throughout your workout to involve both your heart and muscles. • Mountain: Improves performance and stamina by raising the resistance level to high peaks to simulate the most difficult outdoor terrains.
PROGRAM PROFILES MONITORING YOUR HEART RATE • Step test (ANDES 8 ONLY) : Test your current level of physical fitness.At completion of the program,it will provide feedback regarding your fitness level for you to monitor your progress. Feedback Your Horizon Fitness elliptical trainer offers two heart rate feedback options. You may choose to use the heart rate handlebars, or the chest transmitter (sold separately) for a hands free workout.
PRODUCT SPARE PART LIST Item NO. 1 20 Description Console Mast Set;Semi-Assy;EP247-2KM PRODUCT SPARE PART LIST Item NO. Description B36 Cap;Stabilizer;PVC; Ø60 x 2t;BLF54 Item NO. Description P01 Console Wire;1100(150+400+150) Item NO.
EXPLODED VIEW 16 AN1 7 1 6 10 P01 15 19 13 17 18 4 P08 P07 8 15 P02 P06 B47 B39 A B B38 2-B48 B47 C B49 B35 B49 B31 B40 B36 B38 20 B35 B52 B53 B 22 B34 B33 E 5 B43 B40 B51 E B42 B32 B34 B51 D B37 2 B41 B46 B49 B50 4-B45 C B36 B50 V01 4-B44 B54 A D 23
ELLIPTICAL OWNER’S MANUAL Andes 6 & Andes 8 Owner’s Manual 102710 Rev. 1.