User manual

ManualsBrandsHORIZON ManualsScience KitsFuel cell vehicle H-Racer 2.0 8 years and over

Warning: Make sure these connections are

correct. Any other connection will not allow

proper operation of the car and its fuel cell

power system. Also ensure the wires are not

touching the wheels and the

tubes are not kinked or

pinching.

Place the front and rear bumpers onto the

bumper frames on the chassis.

ASSEMBLY GUIDEH-racer 2.0

What do you need?

H-Racer 2.0 AA batteries=2 Units LR44 batteries=3 UnitsWater=25ml

Connect one of the flexible tubes to the small

purging valve. Make sure the tube is inserted

all the way into the base of the purging valve

nozzle.

Connect another flexible tube to the nozzle of

the refueling input valve. Make sure the tube

is inserted all the way into the base of the

nozzle of the refueling input valve.

Position the fuel cell onto the square slot

located in the middle of the car chassis. The

positive mark on the fuel cell should be

positioned on the side with the red cable, and

the negative mark on the side with the black

cable. Push the fuel cell into the chassis.

TIP: To fit the flexible tubes onto the nozzle of the valve, connect the

tube by twisting it against the nozzle, then push the nozzle into the

tube until the tube is snuggly fitted to the base of the nozzle.

Place the refueling input valve above the

opening on the left side of the chassis. Make

sure the red cable is positioned above the

refueling input valve tubing. Slide the refueling

input valve onto its mount located at the

opening on the side of the chassis. With a

downward motion, click the valve into place

ensuring it is smoothly aligned with the outer

surface of the chassis.

H-racer 2.0

ASSEMBLY GUIDE

Model No.: FCJJ-23

To avoid the risk of property damage, serious injury or

death:

This kit should only be used by persons 12 years old and

up, and only under the supervision of adults who have

familiarized themselves with the safety measures

described in the kit. Keep small children and animals away,

as it contains small parts that could be swallowed. The fuel

cell generates gases that are very easily ignited. Read the

instructions before use and have them ready for reference.

Warning

Battery operation instructions:

1. The removing and inserting of batteries is to be

conducted by the adults only.

When inserting the batteries make sure that you are doing

so with the correct polarity (the positive end of the battery

must match up with the “+” and the negative end of the

battery must match up with the “-” indicated on the battery

pack) and then close the battery compartment.

2. Non-rechargeable batteries are not to be recharged.

3. Different types of batteries such as rechargable, alkline

and standard batteries or new and used batteries are not to

be mixed and should be used separately.

4. The two spare red&black cables are not to be inserted

into an AC socket.

5. Exhausted batteries are to be removed from the battery

compartment.

Place the purging valve above the opening on the right side

of the chassis. Slide the purging valve onto its mount

located at the opening on the side of the chassis. Make

sure the refueling valve tube is not in the way of the purging

valve tubing. With a downward motion, click the valve into

the slot on the chassis. Make sure that the whole body of

the purging valve is positioned in the slot on the chassis

and the purging button is positioned outside the edge of the

chassis.

Position the black cable terminal between the fuel cell

holder and the fuel cell end plates, and position the red

cable terminal in the same manner on the opposite side.

Make sure the holes are aligned.

Align the fuel cell holder with the two holes on the car

chassis. Place the screws into the screw holes and make

sure the screws are entered through the cable terminal

holes and straight into the chassis.

*Please note there are two types of screws. The smaller

screws are used for the fuel cell and the larger screws are

used for the car body.

Use a screwdriver to attach the fuel cell end plate and the

red & black cable terminals to the screw holes on the

chassis. Make sure the metal terminals from the cables

are closely touching the fuel cell end plates. Do not

tighten the screws until the two screws are partially

entered into the chassis. Drive the screws into the

chassis making sure all the parts are connected tightly

without moving.

Force is required to drive these

screws into place, to avoid

damage to the kit ask an adult

to drive in the screws.

Connect one end of the flexible tubes to the

lower nozzle on the storage cylinder and the

other end of the flexible tube to the nozzle on

fuel cell located nearest to the motor. Connect

the other end of the flexible tube on the refueling

input valve to the other nozzle located on the fuel

cell. Connect the purging valve tube to the upper

nozzle located on the storage cylinder. Make

sure all tubes are properly positioned as in

diagram.

*Be careful not to place the bumpers upside down. Make

sure the rear bumpers fit correctly onto the frame.

Position the body of the car onto the chassis. Align the

holes on the chassis with the holes on the car body top.

Use a screwdriver (not included) to attach the body to the

chassis using the set of 4 large screws and make sure the

screws are entered straight into the chassis. Do not

tighten the screws until all screws are partially entered into

the chassis. Drive the screws into the chassis until no

gaps are left between the body and the chassis.

Remove the H2 sticker from its backing and

position it on the car accordingly.

309710146

Summary of content (3 pages)

PAGE 1
H-racer 2.0 ASSEMBLY GUIDE Battery operation instructions: Model No.: FCJJ-23 Warning To avoid the risk of property damage, serious injury or death: This kit should only be used by persons 12 years old and up, and only under the supervision of adults who have familiarized themselves with the safety measures described in the kit. Keep small children and animals away, as it contains small parts that could be swallowed. The fuel cell generates gases that are very easily ignited.
PAGE 2
Place the solar panel in direct sunlight. Enabling DC powered operation Open the battery compartment located underneath the refueling station by sliding the cover according to the arrow. WARNING: Make sure these connections are correct. If connected incorrectly the refueling station may not function properly. Place two 1.5V AA alkaline batteries inside the battery compartment as indicated, then close the battery compartment.
PAGE 3
09710149 H-RACER 2.0 TECHNICAL SUPPORT 1. The car does not move or runs slowly: a. Re-insert the batteries in the remote control or remove the used batteries and insert new batteries into the remote control with correct polarity. b. Turn the switch to “on” position, if it is in the “off” or “warm up” position. c. Activate the fuel cell by turning the switch to "warm up" position. The light under the gas storage cylinder will not flash.