Operation Manual

Preparations4.1.3
See Figures

7a/7.1a
Uncouple leaf 1. A and open approx. 1 m, re-couple leaf.
Set all DIL switches to 2. OFF.
Connect the power supply.3.
DIL switch 4. 1 to ON = single-leaf system
DIL switch 5. 4 to ON = set-up mode
Green LED a. GN flashes = set-up mode
Red LED b. RT is illuminated
Teaching in the 4.1.4 CLOSE end-of-travel position
See Figure

7.2a
Press and hold circuit board button 1. T. Leaf A moves in
the CLOSE direction, comes to a standstill at the end
stop, and the motor switches off.
Release circuit board button 2. T.
The gate is now in the CLOSE end-of-travel position.
The LED RT remains on after the end-of-travel position
has been recorded.
NOTE:
If the gate moves in the OPEN direction, check the motor
connection (see Figure 5.2), if necessary, connect the motor
correctly, perform a factory reset (see section 6.8) and repeat
the steps described in this section.
4.1.5 Teaching in the OPEN end-of-travel position
See Figure

7.2a
Press and hold circuit board button 1. T and move leaf A
into the desired OPEN position. Release circuit board
button T.
If the system overshoots the desired position, press 2.
circuit board button T again to move the leaf back a bit.
The leaf can also be moved forward a bit by pressing
circuit board button T again.
Once the desired end-of-travel position is reached, briefly 3.
press circuit board button P; the OPEN end-of-travel
position has now been taught in. The LED GN briefly
flashes quickly and then slowly.
DIL switch 4. 4 to OFF
The connected safety equipment is activated.a.
Operation via radio is possibleb.
Use circuit board button5. T in press-and-release operation
to trigger three complete gate cycles to teach in the
forces (see section 4.3 and Figure 7.3a).
The forces have been taught in if LED a. GN is
illuminated.
WARNING
Danger of injuries due to faulty safety equipment
In the event of a malfunction, there is a danger of injuries
due to faulty safety equipment.
After the learning runs, the person commissioning the

gate must check the function(s) of the safety
equipment as well as the settings (see section 4.4).
The system is ready for operation only after this.
Double-leaf gate system4.2
Fitting the end stops4.2.1
Mechanical end stops are required for the CLOSE end-of-
travel position (e.g. stop plates *). An electric lock provides
the system with additional protection against vandalism and
wind loads.
Fitting and connecting electric locks *4.2.2
See Figure

6
The polarity does not have to be taken into account if
connecting electric locks from the accessory list.
Preparations4.2.3
See Figures

7b/7.1b
Uncouple leaf 1. A and open approx. 1 m, re-couple leaf.
Leaf B must be closed, otherwise uncouple leaf 2. B, move
it into the CLOSE position, and re-couple leaf.
Set all DIL switches to 3. OFF.
Connect the power supply.4.
DIL switch 5. 4 to ON = set-up mode
Green LED a. GN flashes = set-up mode
Red LED b. RT is illuminated
Teaching in the 4.2.4 CLOSE end-of-travel position
for leaf A
See Figure

7.2b
Press and hold circuit board button 1. T. Leaf A moves in
the CLOSE direction, comes to a standstill at the end
stop, and the motor switches off.
Release circuit board button 2. T.
The gate is now in the CLOSE end-of-travel position.
The LED RT remains on after the end-of-travel position
has been recorded.
NOTE:
If the gate moves in the OPEN direction, check the motor
connection (see Figure 5.3), if necessary, connect the motor
correctly, perform a factory reset (see section 6.8) and repeat
the steps described in this section.
4.2.5 Teaching in the OPEN end-of-travel position for
leaf A
See Figure

7.2b
Press and hold circuit board button 1. T and move leaf A
into the desired OPEN position. Release circuit board
button T.
If the system overshoots the desired position, press 2.
circuit board button T again to move the leaf back a bit.
The leaf can also be moved forward a bit by pressing
circuit board button T again.
Once the desired end-of-travel position is reached, briefly 3.
press circuit board button P; the OPEN end-of-travel
position has now been taught in. The LED GN briefly
flashes quickly and then slowly.
Teaching in the 4.2.6 CLOSE end-of-travel position
for leaf B
See Figures

7.3b/7.4b
Uncouple leaf 1. B and open approx. 1 m, re-couple leaf.
DIL switch 2. 3 to ON = Teach-in double leaf operation for
leaf B.
Press and hold circuit board button 3. T. Leaf B moves in
the CLOSE direction, comes to a standstill at the end
stop, and the motor switches off.
* Accessory, not included as standard equipment!
30
TR10L012-A RE / 05.2010
ENGLISH