Operation Manual

Warranty period
In addition to the statutory warranty from the dealer in the
purchase contract, we provide a warranty for a term of
2 years from the purchase date. There is no warranty on
consumables (e.g. fuses, batteries, lamps). Claims made
under the warranty do not extend the warranty period.
For replacement parts and repairs the warranty period is six
months or at least the remainder of the warranty period.
Prerequisites
A claim under this warranty is only valid for the country in
which the equipment was bought. The product must have
been purchased through our authorised distribution channels.
A claim under this warranty exists only for damage to the
object of the contract itself. Reimbursement of expenditure
for dismantling and fitting, testing of corresponding parts, as
well as demands for lost profits and compensation for
damages, are excluded from the warranty.
The receipt of purchase substantiates your right to claim
under the warranty.
Performance
For the duration of the warranty we shall eliminate any
product defects that are proven to be attributable to a
material or manufacturing fault. We pledge to replace free of
charge and at our discretion the defective goods with non-
defective goods, to carry out repairs, or to grant a price
reduction.
Damages caused by the following are excluded:
improper fitting and connection•
improper initial start-up and operation•
external factors such as fire, water, abnormal •
environmental conditions
mechanical damage caused by accidents, falls, impacts•
negligent or intentional destruction•
normal wear or deficient maintenance•
repairs conducted by unqualified persons•
use of non-original parts•
removal or defacing of the product number•
Replaced parts become the property of the manufacturer.
Excerpt from the Declaration of 11
Incorporation
(as defined in EC Machinery Directive 2006/42/EC for
incorporation of partly completed machinery according to
annex II, part B)
The product described on the rear side has been developed,
constructed and produced in accordance with the:
EC Machinery Directive 2006/42 EC•
EC Construction Products Directive 89/106/EEC•
EC Low-Voltage Directive 2006/95/EC•
EC Electromagnetic Compatibility Directive 2004/108/EC•
Applied and consulted standards and specifications:
EN ISO 13849-1, PL „c“, Cat. 2 •
Safety of machinery – Safety-related parts of control
systems – Part 1: General principles
EN 60335-1/2, when applicable •
Safety of electrical appliances/Operators for doors
EN 61000-6-3 •
Electromagnetic compatibility – Electromagnetic radiation
EN 61000-6-2 •
Electromagnetic compatibility – Interference immunity
Partly completed machinery as defined in the EC Directive
2006/42/EC is only intended to be incorporated into or
assembled with other machinery or other partly completed
machinery or equipment, thereby forming machinery to which
this directive applies.
This is why this product must only be put into operation after
it has been determined that the entire machine/system in
which it will be installed corresponds with the guidelines of
the EC Directive mentioned above.
Technical Data12
Max. gate leaf width 2,500 mm
Max. gate height 2,000 mm
Max. gate weight 200 kg
Max. gate leaf infill Dependent on the gate
surface. Regional wind loads
must be taken into account if
using gate infills
(EN 13241- 1).
Rated load See data label
Max. pull and push force See data label
Max. spindle speed Approx. 16 mm/s
Gate locking Electric lock for post and
floor locking, recommended:
From a leaf width •
≥ 1.500 mm
With partial infill•
With increased wind •
load
Operator release On operator, with eye bolt
Operator housing Plastic
Mains voltage Rated voltage 230 V/50 Hz,
power input approx. 0.15 kW
Stand-by power input Approx. 12 W (without
additional accessories
connected)
Control Microprocessor control
system, programmable via
8 DIL switches, control
voltage 24 V DC, protection
category IP 65
Max. control/operator
cable length 40 m
Operating mode S2, short-time duty
4 minutes
Temperature range -20°C to +60°C
Travel/force limit Electronic
Automatic safety cut-out Force limit for both
operational directions, self-
programming and testing
Hold-open phase for
automatic timed closing
60 seconds
(photocell required)
Motor Spindle unit with 24 V DC
motor and worm gear,
protection category IP 44
Radio remote control 2-channel receiver,
hand transmitter
TR10L012-A RE / 05.2010 37
ENGLISH