Manual

ManualsBrandsHorner APG ManualsHardwareSmartStack I/O HE-DAC106*

MAN0453-04 10 NOV 2006 PAGE 1

DAC106

Information is subject to change without notice. SmartStack is a trademark of Horner APG, LLC.

This datasheet also covers products starting with IC300.

1 SPECIFICATIONS

DAC106

Number of

Channels

Maximum Loop Resistance

500 Ω

Output Ranges

(including over-

range)

0–20.47 mA;

10 VDC Compliance

Additional error for

temperatures other than

25°C

0.005% / °C

Resolution

14-Bits

Analog Outputs;

Output Points Required

Peak Output

Voltage

10 VDC Max.

Operating Temperature

0°–60° Celsius

PLC Update Rate Set by PLC Scan

Rate

External Power Supply None

Current Output

Resolution

14-Bits

Terminal Type

Spring Clamp,

Removable

Required Power

(Steady State)

3.3 W

(139 mA @24 VDC)

Weight 9.5 oz. (270 g)

Required Power

(Inrush)

Negligible

Maximum Error at

25°C

0.05% Full Scale

See Compliance Table at

http://www.heapg.com/Support/compliance.

htm

4–20 mA Sourcing

Analog Output Module

HE800DAC106 /

HE-DAC106*

14-Bit Resolution

* HE- denotes plastic case.

Summary of content (8 pages)

PAGE 1
MAN0453-04 DAC106 10 NOV 2006 PAGE 1 4–20 mA Sourcing Analog Output Module HE800DAC106 / HE-DAC106* 14-Bit Resolution * HE- denotes plastic case. This datasheet also covers products starting with IC300. 1 SPECIFICATIONS DAC106 Number of Channels Output Ranges (including overrange) Resolution Peak Output Voltage PLC Update Rate Current Output Resolution Required Power (Steady State) Required Power (Inrush) Maximum Error at 25°C DAC106 4 0–20.
PAGE 2
PAGE 2 2 10 NOV 2006 MAN0453-04 DAC106 WIRING * LOAD LOAD Pin 1+ 1- LOAD Information is subject to change without notice. 3+ 3- LOAD 4+ 4- 2+ 2- 2+ 23+ 3- * 1- OCS Bottom View – Shows Corresponding I/O Pin Signal DAC106 Channel 1+ Common Shield Channel 2+ Common Shield Channel 3+ Common Shield Channel 4+ Common Shield 1+ 4+ 4- 001DAC004 SmartStack is a trademark of Horner APG, LLC.
PAGE 3
MAN0453-04 DAC106 3 10 NOV 2006 PAGE 3 INTERNAL CIRCUIT SCHEMATIC SmartStack Analog Out I/O Connector 1+ Field Side From Controller + - 1- Specification for transient voltage suppressors (transorbs) used on output circuitry is 15 V, 300 W. 4 CONFIGURATION Note: The status of the I/O can be monitored in Cscape Software. Preliminary configuration procedures that apply to SmartStack™ Modules are contained in the hardware manual of the controller you are using.
PAGE 4
PAGE 4 5 10 NOV 2006 MAN0453-04 DAC106 OUTPUT CONVERSION FACTOR The following table describes how program data values are scaled to real-world analog voltage outputs by the module. Given a desired output current, the data value is converted by using the conversion factor from the table. The following formula is used: Data = Output Current (mA) / Conversion Factor Example: The user selects a current range of +20 mA: 1) The desired output current is 12 mA.
PAGE 5
MAN0453-04 DAC106 6 10 NOV 2006 PAGE 5 INSTALLATION / SAFETY Warning: Remove power from the OCS controller, CAN port, and any peripheral equipment connected to this local system before adding or replacing this or any module. a) b) c) d) e) All applicable codes and standards are to be followed in the installation of this product. Shielded, twisted-pair wiring should be used for best performance. Shields may be terminated at the module terminal strip.
PAGE 6
PAGE 6 10 NOV 2006 MAN0453-04 DAC106 For detailed installation and a handy checklist that covers panel box layout requirements and minimum clearances, refer to the hardware manual of the controller you are using. (See the Additional References section in this document.): • • All applicable codes and standards need to be followed in the installation of this product. For I/O wiring (discrete), use the following wire type or equivalent: Belden 9918, 18 AWG or larger.
PAGE 7
MAN0453-04 DAC106 7 10 NOV 2006 PAGE 7 ADDITIONAL REFERENCES The following information serves as a general listing of Horner controller products and other references of interest and their corresponding manual numbers. Visit our website listed in the Technical Support section to obtain user documentation and updates. Note: This list is not intended for users to determine which products are appropriate for their application; controller products differ in the features that they support.
PAGE 8
PAGE 8 10 NOV 2006 MAN0453-04 DAC106 NOTES Information is subject to change without notice. SmartStack is a trademark of Horner APG, LLC.