User Manual

ManualsBrandsHorner APG ManualsHardwareSmartStix HE559

MAN0519-10 _______ Specifications / Installation

_________________________________________________________________________________________________________________________________________________________________________________________________________

02/24/2009 Page 1 of 3 ECN # 952

SmartStix™

User Manual for the CsCAN

Versions (HE550 or HE559) of:

DQM601 DQM606

DQM701 DQM706

DIM610 DIM710

DIQ811 DIQ816

DQM602

Remote I/O for the

OCS/RCS Family

20 February 2009 MAN0519-10

1 Technical Support

For user manual updates and technical assistance, contact Technical Support:

North America: (317) 916-4274

or visit our website at www.heapg.com.

Europe: (+) 353-21-4321-266

or visit our website at www.horner-apg.com.

2 Installation / Safety

a. All applicable codes and standards need to be followed in the installation of this product.

b. For I/O wiring (discrete), use the following wire type or equivalent: Belden 9918, 18 AWG

or larger.

c. For detailed installation and programming information, refer to the Control Station

Hardware Manual.

3 Model Numbers

Model Prefix Description

HE550 CsCAN model with non-removable terminal strip

HE559

CsCAN model with removable terminal strip

Long or Short

Dimension

Description

DIM610

(Short)

16 DC Inputs (24VDC, positive/negative logic)

DIM710

(Long)

32 DC Inputs (24VDC, positive/negative logic)

DQM601 / 606*

(Short)

16 DC Outputs (24VDC, negative logic, 0.5A)

(Note: If using DQM601 with a non-removable terminal strip, the

output rating is 0.1A.)

(* DQM606 uses positive logic.)

DQM701 / 706**

(Long)

32 DC Outputs (24VDC, negative logic, 0.5A)

(Note: If using DQM701 with a non-removable terminal strip, the

output rating is 0.1A.)

(** DQM706 uses positive logic.)

DQM602

(Long)

16 Relay Outputs (250VAC, 30VDC, 2.0A)

DIQ811 / 816***

(Long)

16 DC Inputs (24VDC, positive/negative logic)

16 DC Outputs (24VDC, negative logic, 0.5A)

(Note: If using DIQ811 with a non-removable terminal strip, the

output rating is 0.1A.)

(*** DIQ816 uses positive logic.)

4 Dimensions

a. Long Dimensions

SmartStix modules come in two sizes depending upon the model number. See

Section 3 to determine if a module has long or short dimensions.

b. Short Dimensions

c. Terminal Strips

5 General Specifications

General Specifications

Storage

Temperature

-25° to 70° C

Operating and

Storage Humidity

5 to 95% Non-condensing

Operating

Temperature

0° to 55° C

Pollution degree

2 or lower

Atmosphere

Free from

corrosive gases

and excessive

dust

Cooling method Self-cooling

Vibration

Occasional Vibration

Frequency Acceleration Amplitude

Sweep

Count

10 ≤ f < 57 Hz

- 0.075 mm

57 ≤ f ≤ 150 Hz

9.8 m/s

{1G} -

10 times in

each direction

for X,Y,Z

Continuous Vibration

Frequency Acceleration Amplitude

Sweep

Count

10 ≤ f <

57 Hz

- 0.035 mm

57≤ f ≤

150 Hz

4.9 m/s

{0.5G} -

10 times in

each direction

for X,Y,Z

Shocks

Maximum shock

acceleration

147 m/s

{15G}

Duration Time 11 ms.

Pulse Wave Half sine wave pulse (3 times in each of X, Y, Z directions)

Noise Immunity

Square wave impulse

noise

AC: ± 1,500VDC

DC: ± 900VDC

Electrostatic

Discharge

Voltage: 4kV (contact discharge)

Radiated

electromagnetic field

27 – 500MHz, 10V/m

Severity

level

All power

modules

Digital I/Os

(Ue ≥24V)

Digital I/Os

(Ue < 24 V)

Analog I/Os

Communication

I/Os

Fast Transient

Burst Noise

Voltage 2 kV 1 kV 0.25 kV

6 Network Cable

For detailed wiring information, refer to the Control Station Hardware Manual. A handy

checklist is provided that covers panel box layout requirements and minimum clearances. See

Section 1 for our web address.

Pin Description

RED 1 V+

WHT 2 CAN_H

NC 3 No Connection

BLU 4 CAN_L

BLK 5 V-

7 ID Switches (Setting CsCAN Network Ids)

CsCAN Network IDs are set using the hexadecimal number system from 01 to FD. The decimal

equivalent is 1-253. Refer to Section 10, which shows the decimal equivalent of hexadecimal

numbers. Set a unique Network ID by inserting a small Phillips screwdriver into the two identical

switches. Note: The CsCAN Baud Rate for SmartStix I/O is fixed at 125KBaud

8 LEDs

a. Diagnostic LED Indicators

Diagnostic LED State Meaning

Solid Red RAM or ROM test failed

Blinking Red I/O test failed

Blinking Green Module is in power-up state

MS: (indicates fault status of

Module )

Solid Green Module is running normally

Solid Red Network Ack or Dup ID test failed

Blinking Red Network ID test failed

Blinking Green

Module is in Life Expectancy default

state

NS: (indicates fault status of

Network)

Solid Green Network is running normally

b. Status LED Indicators

The Power Status LED illuminates Red when power is applied to the module. There are I/O Status

LED indicators for each of the Digital I/O points, which illuminate Red when an I/O point is ON.

9 SmartStix Modules

a. DIM610: 16 DC IN, Positive / Negative Logic

DIM610 Specifications

Number of input points 16

OFF to ON

Response

0 - 3ms. or less

Rated Input Current

7mA

ON to OFF

Response

0 - 3ms. or less

ON Voltage Level 19VDC or less Common

Terminal

16 points / COM

OFF Voltage Level 6VDC or less Operating

Indicator

LED turns on during

ON state of input

Input Characteristics Bidirectional

Isolation Method Photo Coupler

External

Connections

Terminal block

connector (M3 x 6

screws)

Rated Voltage 11 – 25 VDC Altitude for

use

Up to 2,000m

Internal power

Consumption (mA)

200mA

Weight 5.6 oz. (159 g)

b. DIM710: 32VDC IN, Positive / Negative Logic

DIM710 INPUTS

Number of input

points

OFF to ON Response 0 - 3ms. or less

Rated Input Current 7mA ON to OFF Response 0 - 3ms. or less

ON Voltage Level 19VDC or less Common Terminal 16 points / COM

OFF Voltage Level 6VDC or less

Isolation Method Photo Coupler

Operating Indicator

LED turns on

during ON state

of input

Input

Characteristics

Bidirectional External Connections

Terminal block

connector (M3 x

6 screws)

Rated Voltage 11 – 25 VDC

Internal power

Consumption (mA)

300

Weight 8.36oz. (237 g)

Cscape, SmartStix and CsCAN are trademarks of Horner APG.

This information is subject to change without notice.

Warning: Consult user

documentation.

Warning: Electrical Shock

Hazard.

For Electronic Information, see

www.HornerOCS.com.

Signal

DIM610

NC*

No Connection

(*Do not Connect)

FG Frame Ground

NC*

No Connection

(*Do not Connect)

I1 Input 1

I2 Input 2

I3 Input 3

I4 Input 4

I5 Input 5

I6 Input 6

I7 Input 7

I8 Input 8

I9 Input 9

I10 Input 10

I11 Input 11

I12 Input 12

I13 Input 13

I14 Input 14

I15 Input 15

I16 Input 16

C Common

NC No Connection

I10

24VDC

I11

I12

I13

I14

I15

I16

006DIM005-R1

4.55 [115.6mm]

4.21 [106.9mm]

1.97 [49.9mm]

1.62 [41.1mm]

0.18 [4.6mm]

1.87

[47.5mm]

0.31

[7.9mm]

HE559-With Removable

Strip

1.53

[38.9mm

]

0.31

[7.9mm

]

HE550- Without

Removable Terminal

Recommended Cable

Thick:

(Max Distance = 500m)

Belden 3082A

Thin:

(Max Distance = 100m)

Belden 3084A

Close-up of Switches

006DIM001

Use this switch to set

the Low Digit – has

an x1 multiplier.

Use this switch to set the

High Digit –has an x16

multiplier.

I/O Status LEDs

Power and Diagnostic

LEDs

INPUT

LO (x1)HI (x16)

MS NSPWR

SmartStix I/O

21 4 5 6 7 8 113 9 12 13 14 15 1610

INPUTS

LO (x1)HI (x16)

MS NSPWR

SmartStix I/O

21 4 5 6 7 8 113 9 12 13 14 15 1610

Signal

DIM710

NC*

No Connection

(*Do not Connect)

FG Frame Ground

NC*

No Connection

(*Do not Connect)

I1 Input 1

I2 Input 2

I3 Input 3

I4 Input 4

I5 Input 5

I6 Input 6

I7 Input 7

I8 Input 8

I9 Input 9

I10 Input 10

I11 Input 11

I12 Input 12

I13 Input 13

I14 Input 14

I15 Input 15

I16 Input 16

C1 Isolated Common 1

I17 Input 17

I18 Input 18

I19 Input 19

I20 Input 20

I21 Input 21

I22 Input 22

I23 Input 23

I24 Input 24

I25 Input 25

I26 Input 26

I27 Input 27

I28 Input 28

I29 Input 29

I30 Input 30

I31 Input 31

I32 Input 32

C2 Isolated Common 2

NC No Connection

I10

24VDC

I11

I12

I13

I14

I15

I16

I31

I29

I30

I27

I28

I25

I26

I23

I24

I21

I22

I19

I20

I17

I18

24VDC

I32

006DIM006-R1

6.95 [176.5mm]

6.61 [167.9mm]

1.62 [41.1mm]

0.18 [4.6mm]

1.97 [49.9mm]

Summary of content (3 pages)

PAGE 1
MAN0519-10 _______ 4 SmartStix™ Dimensions 9 a. Long Dimensions SmartStix modules come in two sizes depending upon the model number. See Section 3 to determine if a module has long or short dimensions. Shocks 147 m/s2 {15G} Number of input points User Manual for the CsCAN Versions (HE550 or HE559) of: Square wave impulse noise Electrostatic Discharge Radiated electromagnetic field Fast Transient Burst Noise 6.95 [176.
PAGE 2
MAN0519-10 c. _______ DQM601: 16 DC OUT, Negative Logic DQM606: 16 DC OUT, Positive Logic d. DQM601 / DQM606 Outputs Number of output points 1 DQM 601A •DQM 601B •DQM 606 OFF Leakage Current Max. Inrush Current per channel Voltage Current OFF to ON Response ON to OFF 24VDC Response 0.1A Max. per output 2A per common Output Type 0.5A Max. per output 3A per common 24VDC Rated Load Voltage Max.
PAGE 3
MAN0519-10 10 _______ Internal Wiring d. DQM701 / DQM706 a. DIM610 I/O Connector I/O Connector DQM701 SmartStix 11 C1 I/O Connector Field Side SmartStix - Q1 V+ To Controller C From Controller Q32 To Controller + Specification for transient voltage suppressors (transorbs) used on output circuitry is 400VDC, bi-directional 400 watts. b. DIM710 Electro-mechanical relays comply with IEC1131-2. f.