Owner's manual

MAN0895-01 Specifications / Installation
_________________________________________________________________________________________________________________
03/03/2009 Page 1 of 3 ECN # 952
1 GENERAL SPECIFICATIONS
General Specifications
Storage
Temperature
-25° to 70° C
Operating and
Storage
Humidity
5 to 95% Non-condensing
Operating
Temperature
0° to 55° C
Pollution
degree
2 or lower
Atmosphere
Free from
corrosive
gases and
excessive
dust
Cooling
method
Self-cooling
Vibration
Occasional Vibration
Frequency Acceleration Amplitude
Sweep
Count
10 ≤ f < 57 Hz
- 0.075 mm
57 ≤ f ≤ 150 Hz
9.8 m/s
2
{1G} -
10 times in each
direction for X,Y,Z
Continuous Vibration
Frequency Acceleration Amplitude
Sweep
Count
10 ≤ f <
57 Hz
- 0.035 mm
57≤ f ≤
150 Hz
4.9 m/s
2
{0.5G} -
10 times in each
direction for X,Y,Z
Shocks
Maximum shock
acceleration
147 m/s
2
{15G}
Duration Time 11 ms.
Pulse Wave Half sine wave pulse (3 times in each of X, Y, Z directions)
Noise Immunity
Square wave
impulse noise
AC: ± 1,500VDC
DC: ± 900VDC
Electrostatic
Discharge
Voltage: 4kV (contact discharge)
Radiated
electromagnetic
field
27 – 500MHz, 10V/m
Severity
level
All power
modules
Digital
I/Os
(Ue ≥24V)
Digital I/Os
(Ue < 24 V)
Analog I/Os
Communication
I/Os
Fast Transient
Burst Noise
Voltage 2 kV 1 kV 0.25 kV
2 DIMENSIONS
a. DIM710
b. DIM610
c. Terminal Strips
3 NETWORK CABLE
For detailed wiring information, refer to the Control Station Hardware Manual. A
handy checklist is provided that covers panel box layout requirements and minimum
clearances. See Section 10 for our web address.
Pin Description
RED 1 V+
WHT 2 CAN_H
NC 3 No Connection
BLU 4 CAN_L
BLK 5 V-
4 ID SWITCHES (SETTING CSCAN NETWORK IDs)
CsCAN Network IDs are set using the hexadecimal number system from 01 to FD. The
decimal equivalent is 1-253. Refer to Section 8, which shows the decimal equivalent of
hexadecimal numbers. Set a unique Network ID by inserting a small Phillips screwdriver
into the two identical switches. Note: The CsCAN Baud Rate for SmartStix I/O is fixed at
125KBaud
SmartStix
TM
HE559DIM610/HE559DIM710
Remote I/O for the OCS/RCS Family
16 DC Inputs (24VDC, positive/negative logic) / 32 DC Inputs (24VDC, positive/negative logic)
4.55 [115.6mm]
4.21 [106.9mm]
1.97 [49.9mm]
1.62 [41.1mm]
0.18 [4.6mm]
1.87
0.31
HE559
-
With Removable
Strip
6.95 [176.5mm]
6.61 [167.9mm]
1.62 [41.1mm]
0.18 [4.6mm]
1.97 [49.9mm]
Close-up of Switches
006DIM001
Use this switch to set
the Low Digit – has
an x1 multiplier.
Use this switch to set the
High Digit –has an x16
multiplier.
I/O Status LEDs
Power and Diagnostic
LEDs
INPUT
S
LO (x1) HI (x16)
MS NS PWR
SmartStix I/O
2 1 4 5 6 7 8 11 3 9 12 13 14 15 16 10
INPUTS
LO (x1) HI (x16)
MS NS PWR
SmartStix I/O
2 1 4 5 6 7 8 11 3 9 12 13 14 15 16 10
Recommended Cable
Thick:
(Max Distance =
500m)
Belden 3082A
Thin:
(Max Distance =
100m)
Belden 3084A