MAN0561-02 27 FEB 2007 PAGE 1 Analog I/O Module HE559MIX977 8 Input Channels 4 Sourcing Output Channels ±5V / ±10V / 4-20mA / ±20mA CsCAN SmartStix Refer to SmartStix Analog Programming Guide (MAN0703) at www.HornerOCS.com.
PAGE 2 27 FEB 2007 MAN0561-02 Vibration Occasional Vibration Frequency Acceleration Amplitude 10 ≤ f < 57 Hz 57 ≤ f ≤ 150 Hz - 0.075 mm 2 9.8 m/s {1G} Sweep Count 10 times in each direction for X,Y,Z Continuous Vibration Frequency Acceleration Amplitude 10 ≤ f < 57 Hz - 0.035 mm 57≤ f ≤ 150 Hz 4.9 m/s2 {0.5G} - Sweep Count 10 times in each direction for X,Y,Z Shocks Maximum shock acceleration 2 147 m/s {15G} Duration Time 11 ms.
MAN0561-02 3 27 FEB 2007 Page 3 WIRING FG FT NC NC +/- 10V I2v +/- 10V I2i I4v +/- 10V +/- 10V +/20mA I4i C I6v +/20mA I6i +/20mA +/20mA I8v I8i +/- 10V LOAD +/- 10V LOAD 24+ * 24C ** FT NC I1v I1i C I3v I3i I5v I5i Mix977 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 FG FT NC NC I2v I2i I4v I4i C I6v I6i I8v I8i C Q2v Q2i Q4v Q4i C 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 Mix977 24+ * 24C ** FT NC I1v I1i C I3v I3i I5v I5i C I7v I7i Q1v Q1i C Q3v Q3i C I7v FT: Fa
PAGE 4 4 27 FEB 2007 MAN0561-02 INTERNAL WIRING SmartStack Inputs I/O Connector 700KΩ Voltage Input + _ Field Side To Controller 300KΩ Current Input 6V 150Ω Isolated Common SmartStack Outputs I/O Connector Voltage Output Mode 100Ω - Field Side + 100Ω Current Output Isolated Common Mode < From Controller
MAN0561-02 5 27 FEB 2007 Page 5 Channel Mode, Programmable Filter, and Output Default Configuration The network supplies configuration information to the HE550MIX977 in the Consumed Directed Digital Data Words sent to the HE550MIX977. In the first word, the low 12 bits, 1 through 12, are channel mode bits. A low mode bit selects ±10V and a high mode bit selects ±20mA. The next three bits, 13 through 15, are input digital filter time constant codes and the high bit, 16, is an adaptive filter enable bit.
PAGE 6 27 FEB 2007 MAN0561-02 Bits 9 through 12 of the 5th configuration word control the behavior of the analog outputs when network communication is lost. The bit to channel correspondence is the same as for the mode and scale bits. If the corresponding bit is set, the outputs hold the last state. If the corresponding bit is cleared, the outputs are set to the respective value supplied to the HE550MIX977 in the second four words of the Consumed Directed Analog Data sent by the OCS.
MAN0561-02 7 27 FEB 2007 Page 7 SETTING ID SWITCHES CsCAN Network IDs are set using the hexadecimal number system from 01 to FD. The decimal equivalent is 1-253. Refer to following Conversion Table, which shows the decimal equivalent of hexadecimal numbers. Set a unique Network ID by inserting a small Phillips screwdriver into the two identical switches.
PAGE 8 Dec 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 27 FEB 2007 Hex HI LO 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 3 3 3 3 3 3 1 2 3 4 5 6 7 8 9 A B C D E F 0 1 2 3 4 5 6 7 8 9 A B C D E F 0 1 2 3 4 5 6 7 8 9 A B C D E F 0 1 2 3 4 5 Dec 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89
MAN0561-02 8 27 FEB 2007 Page 9 LEDS SmartStix I/O Modules provide diagnostic and status LED indicators. a.
PAGE 10 27 FEB 2007 MAN0561-02 10 INSTALLATION / SAFETY a. b. c. All applicable codes and standards need to be followed in the installation of this product. For I/O wiring (discrete), use the following wire type or equivalent: Belden 8441 or equivalent. For detailed installation information, refer to Chapter Two in the Control Station Hardware Manual (MAN0227). A handy checklist is provided that covers panel box layout requirements and minimum clearances. Warning: Consult user documentation.
