User guide

ManualsBrandsHorner APG ManualsSensorsXL6 OCS HEXT351C115

MAN0887-05-EN Specifications / Installation

__________________________________________________________________________________________________________________________________________________________________

3/2/2010 Page 1 of 8 #1037

1 Specifications

Specifications

Digital DC Inputs Digital DC Outputs

Inputs per Module 12 including 4 configurable HSC inputs Outputs per Module 12 including 2 configurable PWM outputs

Commons per Module 1 Commons per Module 1

Input Voltage Range 12 VDC / 24 VDC Output Type Sourcing / 10 K Pull-Down

Absolute Max. Voltage 35 VDC Max. Absolute Max. Voltage 28 VDC Max.

Input Impedance

10 kΩ

Output Protection Short Circuit

Input Current Positive Logic Negative Logic Max. Output Current per point 0.5 A

Upper Threshold 0.8 mA -1.6 mA Max. Total Current 4 A Continuous

Lower Threshold 0.3 mA -2.1 mA Max. Output Supply Voltage 30 VDC

Max Upper Threshold 8 VDC Minimum Output Supply Voltage 10 VDC

Min Lower Threshold 3 VDC Max. Voltage Drop at Rated Current 0.25 VDC

OFF to ON Response 1 ms Max. Inrush Current 650 mA per channel

ON to OFF Response 1 ms Min. Load None

OFF to ON Response 1 ms

ON to OFF Response 1 ms

HSC Max. Switching Rate

10 kHz Totalizer/Pulse, Edges

5 kHz Frequency/Pulse, Width

2.5 kHz Quadrature

Output Characteristics Current Sourcing (Positive Logic)

Analog Inputs, High Resolution

Number of Channels 2 Thermocouple Temperature Range

B / R / S

2912°F to 32.0°F (1600°C to 0°C)

1652°F to -328°F (900°C to -200°C)

Input Ranges

(Selectable)

0 - 10 VDC

0 – 20 mA

4 – 20 mA

100mV

PT100 RTD,

and J, K, N, T, E, R, S, B Thermocouples

752.0°F to -400.0°F (400°C to -240°C)

1382.0°F to -346.0°F (750°C to -210°C)

K / N

2498.0°F to -400°F (1370°C to -240°C)

Safe input voltage range

10 VDC: -0.5 V to +15 V

20 mA: -0.5 V to +6 V

RTD / T/C: ±24 VDC

Thermocouple Common Mode Range ±10V

Nominal Resolution

10V, 20mA, 100mV: 14 Bits

RTD, Thermocouple: 16 Bits

Converter Type Delta Sigma

Max. Error at 25°C

(*excluding zero)

*4-20 mA ±0.10%*

*0-20 mA ±0.10%*

*0-10 VDC ±0.10%*

RTD (PT100) ±1.0 °C

0-100 mV ±0.05%

Input Impedance

(Clamped @ -0.5 VDC to 12

VDC)

Current Mode:

100 Ω, 35mA Max. Continuous

Voltage Mode:

500 kΩ, 35mA Max. Continuous

Max Thermocouple Error

(After Warm Up Time of One Hour)

±0.2% (±0.3% below -100°C)

%AI full scale

10 V, 20 mA, 100 mV: 32,000 counts full scale.

RTD / T/C: 20 counts / °C

Conversion Speed, Both Channels

Converted

10V, 20mA, 100mV: 30 Times/Second

RTD, Thermocouple: 7.5 Times/Second

Max. Over-Current 35 mA Conversion Time per Channel

10V, 20mA, 100mV: 16.7mS

RTD, Thermocouple: 66.7mS

Open Thermocouple Detect

Current

50 nA RTD Excitation Current

250 µA

Analog Outputs General Specifications

Number of Channels 2

Required Power

(Steady State)

500 mA @ 24 VDC

Output Ranges

0-10 VDC,

0-20 mA

Required Power (Inrush)

30 A for 1 ms @ 24 VDC – DC Switched

2.5 A for 4 ms @ 24 VDC - AC Switched

Nominal Resolution 12 Bits Primary Power Range 10 - 30 VDC

Update rate Once per PLC scan Operating Temperature

-10° to 60° Celsius

Minimum 10 V load

1 kΩ

Storage Temperature 14 to 140°F (-10 to 60°C)

Maximum 20 mA load

500 Ω

Relative Humidity 5 to 95% Non-condensing

Analog Outputs;

Output Points Required

2 Filtering

15Hz hash (noise) filter

1-128 scan digital running average filter

Terminal Type Screw Type,5 mm Removable

Maximum Error at 25°C (excluding

zero)

0.1%

Weight 26.5 oz. (0.751kg)

Additional error for temperatures

other than 25°C

0.01% / °C

USA: http://www.heapg.com/Pages/TechSupport/ProductCert.html

Europe: http://www.horner-apg.com/en/support/ certification.aspx

Clock Accuracy

+/- 35 ppm maximum at 25° C (+/- 1.53 Minutes per Month)

Display Properties

Display Life

Minimum 40000 hours (50%

brightness, 25 deg C)

Display Type 5.7” QVGA TFT

User Keys

5 user-defined Function keys and

a System Key

Display Size 5.7”

Screens supported 1023 Display Screen Dimension 320 x 240

Colors

32768/ 16 shade Grey scale

(XL6M models only)

Display Memory 2.75 MB

XL6/XL6M/XL6e OCS Models

HE-XL105 / HE-XL1M5 / HEXT350C115 / HEXT280C115

HE-XL1E5 / HEXT351C115

12 Digital DC Inputs / 12 Digital DC Outputs

2 Analog Inputs (High Resolution) / 2 Analog Outputs

Summary of content (8 pages)

PAGE 1
MAN0887-05-EN Specifications / Installation XL6/XL6M/XL6e OCS Models HE-XL105 / HE-XL1M5 / HEXT350C115 / HEXT280C115 HE-XL1E5 / HEXT351C115 12 Digital DC Inputs / 12 Digital DC Outputs 2 Analog Inputs (High Resolution) / 2 Analog Outputs 1 Specifications Specifications Digital DC Inputs Inputs per Module 12 including 4 configurable HSC inputs Commons per Module 1 Input Voltage Range 12 VDC / 24 VDC Absolute Max. Voltage 35 VDC Max.
PAGE 2
MAN0887-05-EN Specifications / Installation 3 Panel Cut-Out and Dimensions Connectivity Serial Ports Ethernet 2 Serial Ports – RS232 & RS485 10/100-Mbps (XL6e models only) USB Networking Port for communication with PCs USB and programming Port Removable Removable Media for upto 2 GB of storage for Media programs, data logging or screen capture Smartstix Remote IO modules communicating on CAN Note: Highest usable frequency for PWM output is 65 KHz 2 1. Note: Max. panel thickness: 5 mm.
PAGE 3
MAN0887-05-EN 4 Ports and Connectors Specifications / Installation To Remove I/O Cover: Unscrew 4 screws located on the cover. Remove cover. CAUTION: Do not over tighten screws when replacing the back cover. I/O Jumpers: I/O Jumpers (JP) are located internally. To access, remove I/O cover of unit. Wiring Connectors (J1 / J2 / J3) and I/O Jumpers (JP1 / JP2 / JP3 / JP4) are described in the Wiring and Jumpers section of this document.
PAGE 4
MAN0887-05-EN 4.1 Specifications / Installation Serial Communications MJ1: (RS-232 / RS-485) Use for Cscape programming and Application-Defined Communications. MJ2: (RS-232 / RS-485) Use for Application-Defined Communications.
PAGE 5
MAN0887-05-EN 4.3 Specifications / Installation CAN Network Port and Wiring 5 Wiring and Jumpers • Wire according to the type of inputs / outputs used and select the appropriate jumper option. • Use Copper Conductors in Field Wiring Only, 60/75° C Wiring Specifications Location of I/O jumpers (JP) and wiring connectors (J1 – J3). For I/O wiring (discrete), use the following wire type or equivalent: 2 Belden 9918, 18 AWG (0.8 mm ) or larger. Use the CAN Connector when using CsCAN network.
PAGE 6
MAN0887-05-EN 5.2 Specifications / Installation Wiring Examples J1 H1 H2 H3 H4 NC NC 0V IN1 IN2 IN3 IN4 IN5 IN6 IN7 IN8 HSC1 / IN9 HSC2 / IN10 HSC3 / IN11 HSC4 / IN12 No Connect No Connect Ground J2 J1 Orange Positive Logic Digital In Name Orange I1 I2 I3 I4 I5 I6 I7 I8 Note: The wiring examples show Positive Logic input wiring.
PAGE 7
MAN0887-05-EN 6 Specifications / Installation 7 I/O Register Map Registers Description %I1 to %I24 %I32 %I25 to %I31 %Q1 to %Q16 %Q17 Digital Inputs Output Fault Reserved Digital outputs Clear HSC1 accumulator to 0 Totalizer: Clear HSC2 Quadrature 1-2: Accumulator 1 Reset to max – 1 Clear HSC3 Accumulator to 0 Totalizer: Clear HSC4 Quadrature 3-4: Accumulator 3 Reset to max – 1 Reserved Analog inputs HSC1 Accumulator HSC2 Accumulator HSC3 Accumulator HSC4 Accumulator %Q18 %Q19 %Q20 %Q21 to %Q32 %AI
PAGE 8
MAN0887-05-EN 9 Specifications / Installation Safety When found on the product, the following symbols specify: Warning: Electrical Shock Hazard. Warning: Consult user documentation. This equipment is suitable for use in Class I, Division 2, Groups A, B, C and D or Non-hazardous locations only. WARNING – EXPLOSION HAZARD – Do not disconnect equipment unless power has been switched off or the area is known to be non-hazardous.