Manual

MAN0852-02 21 AUGUST 2007 PAGE 1
HE-XE102-10 Specifications / Installation
1 Specifications
HE-XE102 Specifications
Digital DC Inputs
Inputs per Module
12 including 4 configurable
HSC inputs
Commons per Module 1
Input Voltage Range 12 VDC / 24 VDC
Absolute Max. Voltage 35 VDC Max.
Input Impedance
10 kΩ
Input Current Positive Logic Negative Logic
Upper Threshold 0.8 mA -1.6 mA
Lower Threshold 0.3 mA -2.1 mA
Max Upper Threshold 8 VDC
Min Lower Threshold 3 VDC
OFF to ON Response 1 ms
ON to OFF Response 1 ms
HSC Max. Switching Rate
10 kHz Totalizer/Pulse, Edges
5 kHz Frequency/Pulse, Width
2.5 kHz Quadrature
Digital Relay Outputs
Outputs per Module 6 relay
Commons per Module 6
Max. Output Current per Relay 3 A at 250 VAC, resistive
Max. Total Output Current 5 A continuous
Max. Output Voltage 275 VAC , 30 VDC
Max. Switched Power 1250 VA, 150 W
Contact Isolation to XLE
ground
1000 VAC
Max. Voltage Drop at Rated
Current
0.5 V
Expected Life
(See Derating section for
chart.)
No load: 5,000,000
Rated load: 100,000
Max. Switching Rate
300 CPM at no load
20 CPM at rated load
Type Mechanical Contact
Response Time
One update per ladder scan
plus 10 ms
Analog Inputs, Medium Resolution
Number of Channels 2
Input Ranges
0 - 10 VDC
0 – 20 mA
4 – 20 mA
Safe input voltage range -0.5 V to +12V
Input Impedance
(Clamped @ -0.5 VDC to 12
VDC)
Current
Mode:
100 Ω
Voltage Mode:
500 k Ω
Nominal Resolution 10 Bits
%AI full scale 32,000 counts
Max. Over-Current 35 mA
Conversion Speed
All channels converted once per
ladder scan
Max. Error at 25°C
(excluding zero)
*can be made tighter (~0.25%)
by adjusting the digital filter
setting to 3.
4-20 mA 1.00%
0-20 mA 1.00%
0-10 VDC 1.50%*
Additional error for
temperatures other than 25°C
TBD
Filtering
160 Hz hash (noise) filter
1-128 scan digital running
average filter
Thermistor Inputs, Medium Resolution
Number of
Channels
2
Input Ranges
Input Impedance
(Clamped @ -0.5
VDC to 12 VDC)
10K OHMThermistor
Half Bridge
9.59K ohm pulled up to
4.8 VDC
Nominal Resolution
%AI at 10K Ohm
10 Bits
15,008 counts
Conversion Speed All channels converted once per ladder scan
Max. Error at 25°C
reading / ambient
±0.5°F or ±0.3°C
Using specified linearization
in ladder program
Additional error for
reading / ambient
temperatures other
than 25°C
TBD
Filtering
160 Hz hash (noise) filter
1-128 scan digital running average filter
General Specifications
Required Power
(Steady State)
130 mA @ 24 VDC
Required Power
(Inrush)
30 A for 1 ms @ 24 VDC
Primary Power
Range
10 – 30 VDC
Relative Humidity 5 to 95% Non-condensing
Operating
Temperature
0°C to +50°C
Terminal Type Screw Type, 5 mm Removable
Weight 12 oz. (340.19 g)
CE
UL
See Compliance Table at http://www.heapg.com/Support/compliance.htm
Clock Accuracy +/- 7 Minute/Month at 20C
Highest usable frequency for PWM output is 65 KHz
2 Safety
XLE OCS Model: HE
-
XE102
-
10
12 Digital DC Inputs
2 10k Thermistors , 2 Analog Inputs (Medium Resolution)
6 Digital Relay Outputs
Want More Information?
To download the XLE User
Manual (MAN0805), refer to
Technical Support in this
document.
Warning: Consult
user documentation.
Warning: Electrical
Shock Hazard.
When found on the product, the following symbols specify:
WARNING: To avoid the risk of electric shock or burns,
always connect the safety (or earth) ground before making
any other connections.
WARNING: To reduce the risk of fire, electrical shock, or
physical injury it is strongly recommended to fuse the voltage
measurement inputs. Be sure to locate fuses as close to the
source as possible.
WARNING: Replace fuse with the same type and rating to
provide protection against risk of fire and shock hazards.
WARNING: In the event of repeated failure, do not replace
the fuse again as a repeated failure indicates a defective
condition that will not clear by replacing the fuse.
WARNING: Only qualified electrical personnel familiar with
the construction and operation of this equipment and the
hazards involved should install, adjust, operate, or service this
equipment. Read and understand this manual and other
applicable manuals in their entirety before proceeding.
Failure to observe this precaution could result in severe bodily
injury or loss of life.