Owner's manual

ManualsBrandsHorner APG ManualsSensorsXLe OCS HE-XE103-10

MAN0848-02 21 August 2007 PAGE 1

Specifications / Installation HE-XE103-10

1 Specifications

HE-XE103-10 Specifications

Digital DC Inputs XLE103-10

Digital DC

Outputs

XLE103-10

Inputs per Module

12 including 4 configurable

HSC inputs

Outputs per

Module

12 including 2 configurable

PWM outputs

Commons per

Module

Commons per

Module

Input Voltage

Range

12 VDC / 24 VDC Output Type Sourcing / 10 K Pull-Down

Absolute Max.

Voltage

35 VDC Max.

Absolute Max.

Voltage

28 VDC Max.

Input Impedance

10 kΩ

Output

Protection

Short Circuit

Input Current

Positive

Logic

Negative Logic

Max. Output

Current per

point

0.5 A

Upper Threshold 0.8 mA -1.6 mA

Max. Total

Current

4 A Continuous

Lower Threshold 0.3 mA -2.1 mA

Max. Output

Supply Voltage

30 VDC

Max Upper

Threshold

8 VDC

Minimum Output

Supply Voltage

10 VDC

Min Lower

Threshold

3 VDC

Max. Voltage

Drop at Rated

Current

0.25 VDC

OFF to ON

Response

1 ms

Max. Inrush

Current

650 mA per channel

ON to OFF

Response

1 ms Min. Load None

HSC Max.

Switching Rate

10 kHz Totalizer/Pulse,Edges

5 kHz Frequency/Pulse,Width

2.5 kHz Quadrature

OFF to ON

Response

1 ms

Thermistor

Inputs, Medium

Resolution

XLE103-10

ON to OFF

Response

1 ms

Number of

Channels

Output

Characteristics

Current Sourcing (Pos logic)

General Specifications

Input Ranges

Safe input voltage

range

Input Impedance

(Clamped @ -0.5

VDC to 12 VDC)

10K OHM

Thermistor

Half Bridge

9.59K ohm pulled up to

4.8 VDC

Required Power

(Steady State)

130 mA @ 24 VDC

Required Power

(Inrush)

30 A for 1 ms @ 24 VDC

Nominal Resolution

%AI at 10K Ohm

10 Bits

15,008 counts

Primary Power

Range

10 – 30 VDC

Conversion Speed

All channels converted once

per ladder scan

Relative Humidity

5 to 95% Non-

condensing

Max. Error at 25°C

reading / ambient

±0.5°F or ±0.3°C

Using specified linearization

in ladder program

Operating

Temperature

0°C to +50°C

Terminal Type

Screw Type,5 mm

Removable

Additional error for

reading / ambient

temperatures other

than 25°C

TBD

See Compliance Table at

http://www.heapg.com/Support/compliance.htm

Filtering

160 Hz hash (noise) filter

1-128 scan digital running

average filter

Weight 12.5 oz. (354.36 g)

Clock Accuracy +/- 7 Minute/Month at 20C

Highest usable frequency for PWM output is 65 KHz

2 Panel Cut-Out and Dimensions

Note: Max. panel thickness: 5 mm.

3 Ports / Connectors / Cables

Note: The case of the XLE is black, but for clarity, it is shown in a

lighter gray color.

Want More Information?

To download the XLE User

Manual (MAN0805), refer

to Technical Support

in this

document.

[

]

3.622 [92mm]

001XLE002

Refer to XLE User

Manual (MAN0805) for

panel box information

and a handy checklist of

requirements.

Note:

The tolerance to meet

NEMA standards is

± 0.005” (0.1 mm).

To Remove Back Cover:

Unscrew 4 screws located on

the back of the unit.

Lift lid.

CAUTION: Do not overtighten

screws when screwing the lid

back on.

001ACC009

Power Connector

Power Up:

Connect to Earth Ground.

Apply 10

– 30 VDC.

Screen lights up.

CAN Connector

Use the CAN Connector

when usin

g CsCAN network.

I/O Jumpers (Not Shown): I/O Jumpers (JP) are located

internally. To access, remove back cover of unit.

Wiring Connectors (J1 – J4), I/O Jumpers (JP1-3), and

External Jumpers (RS-485) are described in the Wiring and

Jumpers section of this document.

XLE OCS Model: HE

XE103

12 Digital DC Inputs / 12 Digital Outputs

2 10K Thermistor Inputs

MJ1

(RS-232 / RS-485)

MJ2

(RS-232 / RS-485)

I/O

Jumper

Memory Slot

001XLE029-R2

I/O

Jumper

NET 1

(CsCAN)

Power

DIP

Switch

Summary of content (4 pages)

PAGE 1
MAN0848-02 Specifications / Installation 21 August 2007 PAGE 1 HE-XE103-10 Want More Information? To download the XLE User Manual (MAN0805), refer to Technical Support in this document. XLE OCS Model: HE-XE103-10 12 Digital DC Inputs / 12 Digital Outputs 2 10K Thermistor Inputs Specifications Digital DC Inputs Inputs per Module Commons per Module Input Voltage Range Absolute Max.
PAGE 2
PAGE 2 XLE103-10 21 August 2007 4.2. MAN0848-02 Specifications / Installation External DIP Switch Settings (or Jumpers Settings) Section 3 continued As seen when looking at the top of the XLE unit. Refer to Some XLes have jumpers to set RS- Section 3 for the location of the External Jumpers. 485 port termination, though most use DIP Switches. Memory Slot: Uses Removable Memory for data logging, screen captures, program loading and recipes. Horner Part No.
PAGE 3
MAN0848-02 Specifications / Installation 5 21 August 2007 PAGE 3 XLE103-10 The expression rung may be copied, substituting %AI0002 and %R00011 for %AI0001 and %R0007, and used to linearize the second channel. Contact Horner APG for an example file containing the above program. Analog Conditioning 5.1 Filter 5.3 Filter Constant sets the level of digital filtering according to the following chart.
PAGE 4
PAGE 4 XLE103-10 7. 21 August 2007 Safety Notes When found on the product, the following symbols specify: Warning: Electrical Shock Hazard. Warning: Consult user documentation. WARNING: To avoid the risk of electric shock or burns, always connect the safety (or earth) ground before making any other connections. WARNING: To reduce the risk of fire, electrical shock, or physical injury it is strongly recommended to fuse the voltage measurement inputs.