User's Manual
Table Of Contents
- CONTENTS
- I. Specifications
- 1. Icemaker
- KM-1300SAH
- KM-1300SWH
- KM-1300SRH
- KM-1300SAH3
- KM-1300SWH3
- KM-1300SRH3
- 2. Condensing Unit
- URC-12F
- II. General Information
- 1. Construction
- [a] KM-1300SAH, KM-1300SAH3
- [b] KM-1300SWH, KM-1300SWH3
- [c] KM-1300SRH, KM-1300SRH3
- 2. Controller Board
- [a] Solid-State Control
- [b] Controller Board
- [c] Sequence
- [d] Controls and Adjustments
- [e] Checking the Controller Board
- III. Technical Information
- 1. Water Circuit and Refrigerant Circuit
- [a] KM-1300SAH, KM-1300SAH3
- [b] KM-1300SWH, KM-1300SWH3
- [c] KM-1300SRH, KM-1300SRH3
- 2. Wiring Diagrams
- [a] KM-1300SAH, KM-1300SWH
- [b] KM-1300SRH
- [c] KM-1300SAH3, KM-1300SWH3
- [d] KM-1300SRH3
- 3. Timing Chart
- 4. Performance Data
- [a] KM-1300SAH
- [b] KM-1300SWH
- [c] KM-1300SRH
- [d] KM-1300SAH3
- [e] KM-1300SWH3
- [f] KM-1300SRH3
- IV. Service Diagnosis
- 1. No Ice Production
- 2. Evaporator is Frozen Up
- 3. Low Ice Production
- 4. Abnormal Ice
- 5. Other
- V. Removal and Replacement of Components
- 1. Service for Refrigerant Lines
- [a] Refrigerant Recovery
- [b] Evacuation and Recharge [R-404A]
- 2. Brazing
- 3. Removal and Replacement of Compressor
- 4. Removal and Replacement of Drier
- 5. Removal and Replacement of Expansion Valve
- 6. Removal and Replacement of Hot Gas Valve and Line Valve
- 7. Removal and Replacement of Evaporator
- 8. Removal and Replacement of Water Regulating Valve - Water-Cooled Model Only
- 9. Adjustment of Water Regulating Valve - Water-Cooled Model Only
- 10. Removal and Replacement of Condensing Pressure Regulator (C.P.R.) -
- 11. Removal and Replacement of Thermistor
- 12. Removal and Replacement of Fan Motor
- 13. Removal and Replacement of Water Valve
- 14. Removal and Replacement of Pump Motor
- 15. Removal and Replacement of Spray Tubes
- VI. Maintenance and Cleaning Instructions
- 1. Preparing the Icemaker for Long Storage
- 2. Cleaning and Sanitizing Procedures
- [a] Cleaning Procedure
- [b] Sanitizing Procedure - Following Cleaning Procedure
- 3. Maintenance
44
Problem Possible Cause Remedy
[1] Continued from
previous page.
j) Water Supply Line 1. Water supply off and water
supply cycle does not
finish.
1. Check and get
recommended pressure.
2. Condenser water pressure
too low or off and pressure
control opens and closes
frequently to finally
operate high temperature
safety.
2. Check and get
recommended pressure.
k) Water Solenoid 1. Mesh filter or orifice gets
clogged and water supply
cycle does not finish.
1. Clean.
2. Coil winding opened. 2. Replace.
3. Wiring to water valve. 3. Check for loose
connection or open, and
replace.
l) Controller Board 1. Defective. 1. See "II.2[e] Checking the
Controller Board."
m) 1. OFF Position 1. Move to ON position.
2. Bad contacts. 2. Check for continuity and
replace.
[2] a) Float Switch 1. Connector disconnected. 1. Place in position.
2. Leads opened or defective
switch.
2. Check and replace.
3. Float does not move
freely.
3. Clean or replace.
b) Controller Board 1. Defective. 1. Replace.
c) Contactor 1. Open coil or contacts
worn.
1. Replace.
[3] a) Wash Switch 1. WASH position. 1. Move to ICE position.
2. Bad contacts. 2. Check and replace.
b) High Pressure
Controller
1. Dirty air filter or
condenser.
1. Clean.
2. Ambient or condenser
water temperature too
warm.
2. Reduce temperature.
3. Refrigerant overcharged. 3. Recharge.
4. Refrigerant line or
components plugged.
4. Clean and replace drier.
5. Fan not operating. [Except
water-cooled model]
5. See chart 1.[6]
6. Condenser water pressure
too low or off. [Water-
cooled model only]
6. Check and get
recommended pressure.
Interlock Switch
(Cleaning Valve)
Compressor will not
start or stops
operating.
Water continues to
be supplied, and the
icemaker will not
start.