Manual

ManualsBrandsHotchkis ManualsCar1112 Geometry Corrected Tubular Control Arms, 67-76 Dodge A-Body

1967-1976 Dodge Demon

Hotchkis Performance LLC. 1

1112

67-72 Chrysler A-Body Tubular A-Arms

Installation Instructions

Thank you for your purchase of this Hotchkis Performance product. Your A-Arm set was

designed with the performance and durability you’ve come to expect from Hotchkis

Performance.

Note: Please read the entire installation instructions before starting. Having the right tools

will ensure a smooth install process.

A-ARM INSTALLATION

1. Using a jack or lift, raise the front of the car off the ground and remove the

front wheels.

Summary of content (9 pages)

PAGE 1
967-1976 Dodge Demon 1112 67-72 Chrysler A-Body Tubular A-Arms Installation Instructions Thank you for your purchase of this Hotchkis Performance product. Your A-Arm set was designed with the performance and durability you’ve come to expect from Hotchkis Performance. Note: Please read the entire installation instructions before starting. Having the right tools will ensure a smooth install process. A-ARM INSTALLATION 1.
PAGE 2
1967-1976 Dodge Demon 2. Remove the cotter pin from the ball joint and loosen the castle nut. 3. With the castle nut loose, hit the upright mount with a hammer until the spindle & the rest of the suspension pop loose from the A-Arm ball joint. NOTE: Do not completely remove the castle nut. Loosen the nut until it reaches the end of the bolt. HIT HERE Hotchkis Performance LLC.
PAGE 3
1967-1976 Dodge Demon 4. Support the suspension with a floor jack to relieve the pressure from the castle nut. Remove the castle nut. 5. Unbolt the two cam bolts where the A-Arm is connected to the frame. NOTE: Be sure to mark the cams on the bolts so you can get them back in the right place when you install them. CAM BOLTS 6. Remove stock A-Arm. Hotchkis Performance LLC.
PAGE 4
1967-1976 Dodge Demon 7. Adjust the rod ends on the Hotchkis A-Arms so they are set to .33 inches as shown. .33” 8. Before the new A-Arms can be installed part of the front mounting bracket shown will need to be cut slightly to allow for clearance of the new arms. NOTE: This is the FORWARD mounting bracket. CUT THIS PATTERN Hotchkis Performance LLC.
PAGE 5
1967-1976 Dodge Demon CLEARANCE 9. Install the new A-Arms by following the same instructions in reverse order. When bolting on the rod ends, be sure to use the provided spacers. NOTE: Start by using 1 large and 2 small spacers on each side of the heim joint as shown. Due to tolerances between car to car, you may need to use less or more small spacers on either side to ensure the a-arm is centered between their mounting brackets. Hotchkis Performance LLC.
PAGE 6
1967-1976 Dodge Demon CENTER HEIM JOINTS WITH SPACERS Note: P icture is of Driver side 10. Perform this procedure to the other side and the installation is complete. You will need to have the vehicle professionally align after installation. Your new Hotchkis arms were designed for performance driving which encourages more aggressive alignment specifications than factory.
PAGE 7
1967-1976 Dodge Demon Hotchkis Performance LLC Return Policy & Limited Warranty Effective December 1, 2010 all Hotchkis products must be registered to qualify for warranty at www.hotchkis.net or via the mail-in warranty card, included with the product, within 30 days of the original purchase date. IMPORTANT: This warranty supersedes all other warranties included with this product. Return Policy We want you to be completely satisfied with your Hotchkis Performance product.
PAGE 8
1967-1976 Dodge Demon THERE ARE NO WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. ANY IMPLIED WARRANTIES ARE DISCLAIMED TO THE FULLEST EXTENT PERMITTED BY LAW.
PAGE 9
1967-1976 Dodge Demon Effective December 1, 2010. This return policy and limited warranty supersedes all previous policy and warranty statements. Policies and warranties are subject to change without notice. Hotchkis Performance is not responsible for printing errors. Hotchkis Performance LLC.