Owner's Manual DESIGN INSPIRATION The contents of this manual are subject to change without notice.
Contents Welcome ·································································································1 Features ···································································································1 Panel Introduction ·················································································2 Connections ····························································································2 Main Display ·································································
Welcome Thank you for purchasing a Hotone product. Please read this manual carefully to get the most out of your Omni IR. Please keep this manual in a safe place to use for further reference. The Omni IR is a compact-sized, Impulse Response based cabinet simulator delivering organic, precise guitar/bass cabinet sounds. An internal voltage boost circuit provides tons of headroom, a clear, detailed OLED screen lets you get set up quickly, and variable I/O makes it perfect for any live or recording scenario.
Panel Introduction 1. MASTER: Controls the overall output 2. FUNC. : For switching presets/IRs, editing presets, saving, etc. 3. XLR OUT: Feeds balanced signal to mixers, interfaces, etc. 4. LIFT/GND: Switch to LIFT position to lift the ground wire of XLR OUT jack 5. OUT: Unbalanced output jack 6. OLED SCREEN: Shows preset numbers, setting values and other operation info 7. THRU: Feeds unprocessed dry signal to other devices or reamping 8. IN: For plugging in instruments or other effects 9.
Connections For live performance ● For reamping ● OR Note: Always mute the mixer/audio interface or turn down the volume knob on your amp before plugging or unplugging power jacks, cables, etc. This will reduce the chance of hearing/device damage.
Main Display The Main Display will come up as shown below after you plug in your power supply: 2 1 2 1 3 3 1- Current preset number, Omni IR supports 40 presets ranging from 00 to 39 2- Indicates the IR name you’re using in current preset 3- Shows only when the EQ is on Select a Preset In Main Display, turn the FUNC. knob to change presets. Turn the knob clockwise to cycle through presets in the order of 00, 02, 03, …, 39 then 00. Turn the knob counterclockwise to change presets in the opposite order.
Edit 2. Edit detailed parameters In IR select menu, press the FUNC. knob to enter Edit Menu. The screen will come up as shown below: Turn the FUNC. knob to move the cursor on EDIT PRESET, then press FUNC. knob to enter Preset Edit Menu: Preset Edit Menu: 1-Return to previous menu 2-Indicates current cursor position (the PRESET VOL is now selected). 1 2 In this menu, turn FUNC. knob to select a parameter (hollow cursor) or edit parameters (solid cursor), press the FUNC.
Assign Footswitch Function In Edit Menu, select FS FUNCTION to enter Footswitch Function Assign Menu. The screen will come up as shown below: You can assign 2 different functions to FS TAP (tap the footswitch) and FS HOLD (hold the footswitch): MUTE ● BYPASS ● PRESET + ● PRESET – The functions cannot be same. ● Software Connect Omni IR to your computer and access the free software to manage your Omni IR device, adjust tonal settings, update firmware, restore settings, and upload third party IR files.
Factory IR files list* PRESET OMNI IR NAME BASED ON MIC TYPE 20 BRIT 66B 2x12 Marshall 1966B* 2x12 Royer R121* 2x12 21 US STDO 2X12 1980s Mesa/Boogie* 2x12 cabinet Shure SM57* 2x12 22 BGR SVA 2x12 Bogner Shiva* 2x12 Shure SM57* 2x12 23 MESH RC2x12 Mesa/Boogie Rectifier* 2x12 AKG C414* 2x12 24 DELX VERB 1x12 Fender Deluxe Reverb* 1x12 Shure SM57* 1x12 25 US CHAP 1x12 Fender Champ* 1x12 Shure SM57* 1x12 26 BRIT 74CX 1x12 Marshall 1974CX* 1x12 Beyerdynamic M160* 1x12 27
DESIGN INSPIRATION
