Operation Manual

25
EN
Whenever the appliance fails to work, check for a solution from the following list before calling for Technical
Assistance Centre.
Troubleshooting
Some problems are indicated by specific messages which flash on the display: make a note of any messages
displayed before calling Assistance.
0DOIXQFWLRQ 3RVVLEOHFDXVHV6ROXWLRQV
7KHGLVKZDVKHUGRHVQRWVWDUW
• The plug has not been inserted into the electrical socket
properly, or there is no power in the house.
• The dishwasher door has not been shut properly.
• A delayed start has been programmed (
see Start-up and use ).
1RZDWHU HQWHUVWKH GLVKZDVKH U
• There is no water in the mains supply.
• The water inlet hose is bent (
see Installation ).
1RZDWHUGUDLQVRXWIURPWKH
GLVK ZDVKHU
• The dishwasher cycle has not yet finished.
• The water outlet hose is bent (
see Installation ).
• The drain duct is blocked.
• The filter is clogged up with food residues.
7KHGLVKZDVKHUPDNHV
H[FHVVLYHQ R LVH
• The dishes are rattling against each other or against the
sprayer arms.
7KHGLVKHV DQGJODVVHVDUH
FRYHUHGLQDZKLWHIL OP RU
OLPHVFDOHGHSRV LWV
• The level of the refined salt is low or the dosage setting is not
suited to the hardness of the water (
see Rinse aid and salt ).
• The lid on the salt dispenser is not closed properly.
• The rinse aid has been used up or the dosage is too low.
• The crockery is made from non-stick material.
7KHGLVKHVDQGJODVVHVDUH
VWUHDN HGRUKDYHDEOXLVK
WLQJH
• The rinse aid dosage is too high.
7KH FUR F NH U\KDVQRWEHHQGUL HG
SURSHUO\
• The rinse aid has been used up or the dosage is too low (
see
Rinse aid and salt
).
• The rinse aid dispenser setting is not high enough.
• A wash cycle without a drying programme has been selected.
7KHGLVKHVDUHQRWFOHDQ
• The racks are overloaded (
see Loading the racks ).
• The crockery has not been arranged well.
• The sprayer arms cannot move freely.
• The wash cycle is too gentle (
see Wash cycles ).
• The detergent has not been measured out correctly or it is not
suited to the type of wash cycle (
see Start-up and use ).
• The filter is dirty or blocked (
see Care and maintenance ).
• The refined salt level is low (
see Rinse aid and salt ).
6KXWRIIWDSDODUP
(you will hear several short beeps)
(the message H2O and the code
ALO6 flashes on the display).
• Turn on the tap and the appliance will start after a few
minutes.
• The appliance lock has been activated because nothing was
done when the beeps sounded. Switch off the machine using
the STANDBY button, turn on the tap and switch the machine
back on after 20 seconds by pressing the same button. Re-
programme the machine and restart the wash cycle.
%ORF N HGILO WHUDODUP
(the code ALO5 flashes on the
display).
• Switch off the machine by pressing the STANDBY button and
clean the filters (
see Maintenance ), then switch the
dishwasher back on by pressing the same button. Re-
programme the machine and restart the wash cycle.
:DWHUORDG L QJVROHQRLG YDO YH
PDOIXQFWLRQDODUP
(the indicator light WATER LEAK
flash on the display).
• Switch off the appliance by pressing the STANDBY button and
switch it back on after a minute. If the alarm continues, turn
off the water tap to reduce the risk of flooding, remove the
plug from the electrical socket and call Assistance.