Daily Reference Guide
Temperature
Every programme has a predened temperature. If you want to change
the temperature, press the “Temp.” button. The value appears on the
display.
Spin Speed
Every programme has a predened spin speed. If you want to change
the spin speed, press the “Spin Speed” button. The value appears on the
display.
KEY LOCK
To lock the control panel, press and hold the “Energy saver” button for
approximately 3 seconds. The symbol will light up on the display
to indicate that the control panel has been locked (with the exception
of the “ON/OFF“ button). This prevents unintentional changes to
programmes, especially with children near the machine. To unlock the
control panel, press and hold the “Energy saver” button for approximately
3 seconds .
HINTS AND TIPS
Sort your laundry according to
Type of fabric/care label (cotton, mixed bres, synthetics, wool, handwash
items). Colour (separate coloured and white items, wash new coloured
items separately). Delicates (wash small items – like nylon stockings – and
items with hooks – like bras – in a cloth bag or pillow case with zip).
Empty all pockets
Objects like coins or lighters can damage your laundry as well as the drum.
Follow the dosage recommendation / additives
It optimizes the cleaning result, it avoids irritating residues of surplus
detergent in your laundry and it saves money by avoiding waste of
surplus detergent
Use low temperature and longer duration
The most ecient programmes in terms of energy consumption are
generally those that perform at lower temperatures and longer duration.
Observe the load sizes
Load your washing machine up to the capacity indicated in the
“PROGRAMME CHART” table to save water and energy.
Noise and remaining moisture content
They are inuenced by the spinning speed: the higher the spinning
speed in the spinning phase, the higher the noise and the lower the
remaining moisture content.
CLEANING & MAINTENANCE
For any cleaning and maintenance, switch o and unplug the washing
machine. Do not use ammable uids to clean the washing machine.
Clean and maintain your washing machine periodically (at least 4 times
per year).
Cleaning the outside of the washing machine
Use a soft damp cloth to clean the outer parts of the washing machine.
Do not use glass or general purpose cleaners, scouring powder or similar
to clean the control panel – these substances might damage the printing.
Checking the water supply hose
Check the inlet hose regularly for brittleness and cracks. If damaged,
replace it by a new hose available through our After-Sales Service or your
specialist dealer.
Cleaning the water lter / draining residual water
Switch o and unplug the washing machine, take out the kitchen plinth
before cleaning the water lter or draining residual water.
The kitchen plinth must be mounted back all the time once the cleaning
operation is over.
If you used a hot wash programme, wait until the water has cooled down
before draining any water. Clean the water lter regularly, to avoid that the
water cannot drain after the wash due to obstruction of the lter. If the water
cannot drain, the display indicates that the water lter may be clogged.
1 . Place a container close to the pump to collect any spillage.
2 . Remove, pulling it out, the “emergency drain hose” from the base
of the washing machine .
Remove the stopper of the “emergency drain hose” at the end of the hose
and let the water ow into the container.
3 . Turn the exhaust lter handle and pull it out of the housing .
When the container of plinth is full with water, plug the stopper to the
hose end, and reinsert the small hose in the washing machine’s base .
After, empty the container .
Afterwards rmly close the emergency drain hose with the stopper .
4. Remove lter: Lay a cotton cloth beneath the water lter, which can
absorb a small amount of rest water . Then remove the water lter by
turning it out anticlockwise .
5 . Clean the water lter: remove residues in the lter and clean it under
running water .
6 . Insert the water lter: Reinsert the water lter again by turning it in
clockwise direction . Make sure to turn it in as far as it goes; the lter
handle must be in vertical position . To test water tightness of the water
lter, you can pour about 1 liter of water into the detergent dispenser .
1
2
Then reinstall the kitchen plinth.
TRANSPORT AND HANDLING
Never lift the washing machine by holding it at the worktop.
Pull out the mains plug, and close the water tap. Make sure that door
and detergent dispenser are properly closed. Disconnect the inlet hose
from the water tap, and remove the drain hose from your draining point.
Remove all rest water from the hoses, and x them so that they cannot
get damaged during transport. Ret the transport bolts. Follow the
instructions for removing the transport bolts in the Installation Guide in
reverse order.
EN
Quick guide