CM 9945 HA
Instructions for use 7
A B C 4
Safety instructions Safeguarding the environment Built-in installation Product description Technical data Using the appliance for the first time Switching on and preheating Making coffee (using coffee beans) Changing the amount of coffee in the cup Adjusting the coffee grinder Making espresso with pre-ground coffee (instead of beans) Running off hot water Making cappuccino Changing the amount of milk and coffee for cappuccino Changing and setting menu parametrs Cleaning and maintenance Switching off the app
Safety instructions Important to be read and observed Before using the appliance, read these safety instructions. Keep them nearby for future reference. These instructions are also available on docs.hotpoint.eu. These instructions and the appliance itself provide important safety warnings, to be observed at all times. The manufacturer declines any liability for failure to observe these safety instructions, for inappropriate use of the appliance or incorrect setting of controls.
Permitted use CAUTION: the appliance is not intended to be operated by means of an external timer or separate remote controlled system. This appliance is intended to be used only in household application. This appliance is Not intended to be used in similar application such as: staff kitchen areas in shops, offices and other working environments; farm houses; by clients in hotels, motels, bed & breakfast and other residential environments. This appliance is not for professional use.
damaged, it must be replaced with an identical one - risk of electrical shock. If the power cable needs to be replaced, contact an authorised service center. Appliances with removable cord: avoid splashes of water on the power cord connector or socket at the back of the appliance. WARNING: Avoid any spillage on the connector and plug. Cleaning and maintenance WARNING: Ensure that the appliance is switched off and disconnected from the power supply before performing any maintenance operation.
Built-in installation Check the minimum measurements required for correct installation of the appliance. The coffee machine must be installed in a column unit, which must in turn be securely fixed to the wall by means of commercial brackets. Attention: • Disconnect the appliance from the mains before carrying out any installation work or servicing. • Kitchen units in contact with the appliance must be heat resistant (min. 65°C).
Secure the power supply cable with the clip provided. The power supply cable must be long enough to allow the machine to be removed from the housing in order to fill the coffee bean container. Regulations require that the appliance is earthed. Electrical connection must be carried out by a qualified electrician in accordance with the manufacturer's instructions. x1 Position the machine on the runners, making sure that the pins engage properly in their seats before securing with the screws provided.
Product description Appliance Control panel See image A on page 4. See image B on page 4. A1Cup tray A2Service door N.B.: the touch-control buttons are activated at the lightest touch of a finger. A3Coffee feed B1 Display: guides the user through use of the machine. B2 MENU Button to activate or deactivate the menu setting mode.
Using the appliance for the first time • Coffee has been used to factory test the machine and it is therefore completely normal for there to be traces of coffee in the mill. • Customize water hardness as soon as possible, following the instructions in paragraph Setting water hardness. 1. Connect the appliance to the mains electricity supply and place the main switch (A23) in position I. 2. The appliance displays “fill tank” in different languages. Extract the water tank (fig.
Making coffee (using coffee beans) 1. The machine is factory-set to make coffee with a standard taste. You can choose coffee with the following tastes: extra-mild, mild, standard, strong or extra-strong, with the option of using preground coffee. To choose the desired taste, press the button (B3) (Figure 8) repeatedly until the required taste is displayed. 2. Place 1 cup under the coffee spouts if you wish to make 1 coffee (Figure 9) or 2 cups for 2 coffees (Figure 9).
Changing the amount of coffee in the cup The appliance is factory-set to automatically deliver the following amounts of coffee: • • • • • Espresso, Small cup, Medium cup, Large cup, Mug. To modify these quantities and set the amount of coffee desired, for example changing the amount of espresso, proceed as follows: • Press the button (B4) repeatedly until the display shows ESPRESSO. • Keep the button (B8) pressed until the display shows the message PROGRAM QUANTITY. Meantime the machines runs off coffee.
Running off hot water • • • • Always check that the machine is ready for use. Check that the water spout is attached to the nozzle (Figure 6). Place a container under the spout. Press button (B11) the display will show HOT WATER PRESS , press (B7) to confirm. The display shows HOT WATER and hot water runs out of the spout, filling the container below (Do not run off hot water for more than 2 minutes at a time). To stop the flow, press the button (B11).
N.B.: • While making cappuccino, you can stop frothed milk or coffee run-off by pressing the button (B10). • To keep the milk frother hygienically clean at all times, always clean the internal tubes of the milk container lid after making cappuccino. The message PRESS CLEAN BUTTON is displayed: - place a container under the milk spout (Figure 25); - press and hold the CLEAN button (C3) on the milk container lid for at least 8 seconds, (Figure 25) to activate cleaning. The message CLEANING...
Setting the language To change the display language, proceed as follows: • Press the MENU button (B2) to access the menu and then buttons (B5) and (B6) to select LANGUAGE. • Press (B7). • Press buttons (B5) and (B6) until the required language is displayed. • Press (B7) to confirm. • Press the MENU button (B2) to exit the menu. Rinsing This function is used to obtain hotter coffee.
Setting water hardness If desired, the interval between descaling cycles can be increased so that descaling is performed less frequently and in accordance with the actual calcium content of the water used. Proceed as follows: • Remove the "Total hardness test" water hardness strip from its packaging (attached to page 2), immerse it fully in the water for a few seconds. Next, remove it and wait around 30 seconds (until it changes colour and red squares appear on the strip).
Energy saving • Press the icon • Press the icons • Press the icon disabled). • Press the icon (B2) to enter the settings menu. (B5) and (B6) until ENERGY SAVING is displayed. (B7) DISABLE? is displayed (or ENABLE? if the function has already been (B7) to enable or disable the function or the icon (B2) to exit the menu. Statistics This function enables you to view the machine statistics.
Cleaning the drip tray WARNING: If the drip tray is not emptied, the water can overflow. This can damage the machine. The drip tray has a water level indicator in the form of a red float (Figure 27). Empty and clean the drip tray before the red float protrudes from the cup tray. To remove the drip tray: 1. Open the service door (Figure 16). 2. Remove the drip tray and the coffee grounds container (Figure 17). 3. Clean the drip tray and the grounds container (A4). 4.
N.B.: If you encounter difficulty inserting the brewing unit, before inserting it adapt it to the right size by pressing it forcefully from both the bottom and top simultaneously as shown in the figure. 7. Once inserted, make sure the two red buttons have clicked out. 8. Replace the drip tray and coffee grounds container. 9. Close the service door. Cleaning the milk container Always clean the tubes inside the milk container (C) after preparing milk.
Displayed messages DISPLAYED MESSAGE POSSIBLE CAUSE REMEDY - The water tank is empty or incorrectly positioned. - Fill the tank with water and/or insert it correctly, pushing it as far as it will go. GROUND TOO FINE ADJUST MILL! INSERT WATER SPOUT AND PRESS . - The ground is too fine so the coffee runs off too slowly. - Turn the grinding adjustment knob one click towards number 7. GROUND TOO FINE ADJUST MILL! (alternating with) PRESS (and then) FILL TANK! - The tank was removed during run-off.
Troubleshooting Below is a list of some possible malfunctions. If the problem cannot be resolved as described, contact After-sales Service. PROBLEM The coffee is not hot. The coffee is not creamy enough. POSSIBLE CAUSE - The cups have not been pre-heated. - The brewing unit has cooled down because 2/3 minutes have elapsed since the last coffee was made. - The set temperature is not high enough. - The coffee is ground too coarsely. - The blend of coffee is unsuitable.
Printed in Italy 10/2017 400010867023A GB
