Instruction booklet GB English, 1 P Português, 19 Contents GB Installation, 2 Where to put your dryer Ventilation Water drain Electrical connection Before you start using your dryer Warnings, 3-4 General safety To minimise the risk of fire Maintenance and Care, 5-6 FTCF 87B Switching off the electricity Cleaning the filter after each cycle Empty the water container after each cycle Cleaning the condenser unit Check the drum after each cycle Cleaning the dryer Dryer description, 7 The features Contr
Installation GB Where to put your dryer Place your dryer at a distance from gas ranges, stoves, heaters, or cook tops because flames can damage the appliance. Minimum gap 10mm If you are going to install the appliance under a work counter, be sure to leave a Minimum gaps 10mm space between 15mm the top and any other objects on or above the machine and a 15mm space between the sides and lateral furnishings or walls. This is to ensure proper air circulation.
Warnings ! The appliance has been designed and built according to international safety standards. These warnings are given for safety reasons and must be followed carefully. ● ● ● General safety This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities, or lack of knowledge if they are given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
Warnings GB To minimise the risk of fire in your tumble dryer, the following should be observed: Tumble dry items only if they have been washed with detergent and water, rinsed and been through the spin cycle. It is a fire hazard to dry items that HAVE NOT been washed with water. Do not dry garments that have been treated with chemical products. Do not tumble dry items that have been spotted or soaked with vegetable or cooking oils, this constitutes a fire hazard.
Maintenance and Care Switching off the electricity ! Unplug your dryer when not using it, when cleaning it and during all maintenance operations. Clean the filter after each cycle The filter is an important part of your dryer: it accumulates lint and fluff that is formed while drying. ! Failure to empty the water container may cause the following: - The dryer will stop heating (so the load may still be damp at the end of the drying cycle) (see The Controls).
Maintenance and Care GB Tap Water container Rear Filter Front Condenser unit Air intake Condenser unit Condenser cover Catches Check the drum after each cycle Quick Tips Turn the drum manually in order to remove small items (handkerchiefs) that could have been left behind. ● ● Remember to clean the door filter and the condenser filter after each load. Remember to empty the water container after each load.
Dryer Description The features Rating plate GB Water container Model & Serial numbers Filter Condenser cover handle (Pull to open) Condenser cover Air intake grille Control panel Indicator PROGRAMME knob ON/OFF Button The ON/OFF button : If the dryer is running and this button is pressed and held for more that 3 seconds the dryer is turned off, it counts down 3, 2, 1, Off and the programme is then cancelled. Press and hold for more than 3 seconds and the dryer reactivates.
The Display The Display has three main functions, each with its corresponding button. GB Dryness Sensing Levels After selecting a programme that has a Sensor Dry option, press and release the button until the required dryness sensing level is displayed. If the sensing option is not available with your selected programme, the display will flash and the buzzer will beep three times. ! Some sensing programmes do not have all seven dryness level options available.
Start and Programmes Choosing a programme 8. Set a delay time and other options if necessary. 9. The START/PAUSE light is flashing green: - press the START/PAUSE button to begin. The green light stops flashing. During the drying programme, you can check on your laundry and take out items that are dry while others continue drying. When you close the door again, press the START/PAUSE button in order to resume drying.
Start and Programmes Shirts High heat option This is a programme for shirts made from cotton. It can be used for load sizes up to 3kg (approximately 10 shirts). Medium heat option This is a programme for shirts made from synthetic materials or a mixture of natural and synthetic materials, such as polyester and cotton. It can be used for load sizes up to 3kg (approximately 14 shirts).
Start and Programmes Jeans ● ● ● ● ● ● GB This is a programme for jeans made from denim cotton. Before drying your jeans turn the front pockets inside out. It can be used for load sizes up to 3kg (approximately 4 pairs). Do not mix dark and light coloured items. It can also be used on other garments made from the same material, such as jackets. The duration of this programme will depend on the size of the load and the spin speed used in your washer.
Start and Programmes EXTRA PROGRAMMES - Programmes Table Heat & Enjoy ✗ ✗ ✗ ✗ ● An Automatic programme 15 Easy Iron ✗ ✗ ✓ ✗ ● An Automatic programme 16 Refresh ✗ ✗ ✓ ✗ ● An Automatic programme Extra Dry 14 ● Cupboard Dry ✗ Light Dry ✓ Iron Dry ✗ Damp Dry ✓ Sensor Dry Heat Level Cuddly Toys Timed Dry Sound 13 Hanger Dry Dryness Levels available (default highlighted ✓ ) Extra Care Options available Delay Timer Programme Hanger Dry Plus GB An Automatic programme
Start and Programmes The Controls Programmes knob ● ! Warning, if after pressing the START/PAUSE button the programme knob position has changed, the new position will NOT change the programme selected. To change a selected programme, press the START/PAUSE button , the light flashes Amber to indicate the programme is paused. Select the new programme and any options required, the light will then flash green. Press the START/PAUSE button again and the new programme will start.
Laundry GB Sorting your laundry Drying times Check symbols on clothing labels to make sure that the articles can be tumble dried. ● Sort laundry by fabric type. ● Empty pockets and check buttons. ● Close zippers and hooks and tie loose belts and strings. ● Wring out each item in order to eliminate as much excess water as possible. ! Do not load dripping wet clothes into the dryer. The table (see below) presents APPROXIMATE drying times in Minutes. Weights refer to dry garments.
Troubleshooting One day your dryer seems not to be working. Before you call your Service Centre (see Service), go through the following troubleshooting suggestions: Problem: Possible causes / Solution: The tumble dryer won’t start. ● GB ● The plug is not plugged into the socket, or not making contact. There has been a power failure. The fuse has blown. Try to plug another appliance into the socket. You are using an extension cord? Try to plug the dryer’s power cord directly into the socket.
Service GB Before calling the Service Centre: ● ● Use the troubleshooting guide to see if you can solve the problem yourself (see Troubleshooting). If not, turn off the dryer and call the Service Centre closest to you. What to tell the Service Centre: name, address and post code. ● telephone number. ● the type of problem. ● the date of purchase. ● the appliance model (Mod.). ● the serial number (S/N). This information can be found on the data label inside the door of the machine.
Product Data... (EU Regulation 392/2012) Brand Hotpoint Ariston Models TCF87B GB FTCF87B Rated capacity of Cotton laundry for the standard programme at full load 8 kg Energy efficiency class B The weighted Annual Energy Consumption (AEc) 559.8 kWh Consumption per year, based on 160 drying cycles of the standard cotton programme at full and partial load, and the consumption of the low-power modes. Actual energy consumption per cycle will depend on how the appliance is used.
Folheto de instruções GB English, 1 P Português, 69 Índice P Instalação, 20 Onde colocar a sua máquina de secar roupa Ventilação Drenagem da água Ligação eléctricas Antes de iniciar a utilização da sua máquina de secar roupa Avisos, 21-22 Segurança Geral Para reduzir o risco de ocorrência de incêndios Manutenção e cuidado, 23-24 FTCF 87B Desligar a electricidade Limpar o filtro depois de cada ciclo Verificar o tambor depois de cada ciclo Limpar a unidade do condensador Esvazie o recipiente de água a
Instalação P Onde colocar a sua máquina Instale a sua máquina a alguma distância de ligações de gás, fogões, aquecedores e placas de cozinha, uma vez que as chamas podem danificar o aparelho. mínima espaço 10 mm Se pretende instalar o aparelho por baixo de uma bancada ou de um balcão, não se mínima espaço esqueça de deixar um 15 mm espaço de 10 mm entre a bancada e quaisquer objectos ou acima do tampo da máquina e um espaço de 15 mm entre as partes laterais da máquina e mobiliário ou paredes.
Avisos ! O equipamento foi concebido e construído de acordo com normas de segurança internacionais. Estes avisos são apresentados por razões de segurança e devem ser seguidos minuciosamente.
Avisos P Para reduzir o risco de ocorrência de incêndios na máquina de secar roupa, deve ter em conta os seguintes aspectos: Seque apenas artigos que tenham sido lavados com água e detergente, enxaguados e centrifugados. Existe um risco de incêndio se secar peças que NÃO tenham sido lavadas com água. Não seque peças de vestuário que tenham sido tratadas com produtos químicos.
Manutenção e Cuidado Desligar a electricidade ! Desligue a secadora quando não estiver em utilização, durante tarefas de limpeza e durante todas as operações de manutenção. ! O não esvaziamento do recipiente de recolha da água pode causar: - A paragem do aquecimento da máquina (o que faria com que a roupa continuasse húmida no fim do ciclo de secagem) (ver Controlos).
Manutenção e Cuidado P Torneira Recipiente de água Traseira Filtro Frente Unidade do condensador Entrada de ar Unidade do condensador Tampa do condensador Suportes Verificar o tambor depois de cada ciclo Rode o tambor manualmente, de modo a remover pequenos objectos (lenços) que podem ter ficado na máquina. Limpar o tambor ! Não utilize agentes de limpeza de aço inoxidável ou palha de aço, abrasivos, para limpar o tambor.
Descrição da máquina de secar Características Chapa de classificação P Recipiente de água Números de modelo e de série Filtro Pega da tampa do condensador (Puxar para abrir) Tampa do condensador Entrada de ar Painel de controlo botão dos PROGRAMAS Botão LIGAR/DESLIGAR O botão LIGAR/DESLIGAR : Se a máquina de secar estiver a funcionar, este botão for premido e mantido por mais de 3 segundos e a máquina de secar for desligada, ocorre uma contagem decrescente de 3, 2, 1, Desligar e o programa é então can
O Visor O Visor possui três funções principais, cada uma com o seu botão correspondente. P Níveis de Medição da Secagem Após seleccionar um programa que possua a opção de Secagem por sensor, prima o botão e solte-o até ser apresentado o nível de medição da secagem apropriado. Se a opção de medição não se encontrar disponível com o programa seleccionado, o visor irá piscar e o alarme sonoro irá tocar três vezes. ! Alguns programas de medição não possuem as cinco opções de nível de secagem disponíveis.
Arranque e Programas Escolher um programa 1. 2. Ligue a secadora a uma tomada de corrente eléctrica. Escolha a sua roupa de acordo com o tipo de tecido (ver Roupa). 3. Abra a porta e certifique-se de que o filtro está limpo e bem colocado e de que o recipiente da água está vazio e na respectiva posição (ver Manutenção). 4. 5. 6. 7. Carregue a máquina e certifique-se de que nenhuma peça fica presa no fecho da porta. Feche a porta.
Arranque e Programas Camisas P Opção Calor Alto Este programa foi concebido para camisas de algodão. Pode ser utilizado para cargas até 3 kg (aproximadamente 10 camisas). Opção de Calor Médio Este programa foi concebido para camisas feitas a partir de materiais sintéticos ou de uma mistura de materiais sintéticos e naturais, como poliéster e algodão. Pode ser utilizado para cargas até 3 kg (aproximadamente 14 camisas).
Arranque e Programas Calças de ganga Este programa foi concebido para calças de ganga. Antes de secar as calças de ganga, vire os bolsos da frente do avesso. ● Pode ser utilizado para cargas até 3 kg (aproximadamente 4 pares). ● Não misture peças de roupa escuras e claras. ● Pode também ser utilizado com outras peças de roupa feitas a partir do mesmo material, como casacos. ● A duração do programa irá depender da dimensão da carga e da velocidade de rotação utilizada na sua máquina de lavar.
Arranque e Programas PROGRAMAS EXTRA (EXTRA_ – Tabela de Programas Calor & Conforto ✗ ✗ ✗ ✗ ● Um programa Automático 15 Engomar fácil ✗ ✗ ✓ ✗ ● Um programa Automático 16 Refrescante ✗ ✗ ✓ ✗ ● Um programa Automático Secagem Extra (Extra Seco) 14 ● Secagem para armário ✗ Secagem suave ✓ Secagem para pendurar (extra) ✗ Secagem com humidade Nivel de calor ✓ Secagem por Sensor Som Peluche Secagem Temporizada Cuidado Extra 13 Secagem para pendurar Níveis de Secagem dispo
Arranque e Programas Controlos Botão dos PROGRAMAS ● ! Cuidado, se a posição do botão os PROGRAMAS fôr alterada após premir o botão INICIAR/PAUSA , a nova posição NÃO alterará o programa seleccionado. Para alterar um programa seleccionado, prima o botão INICIAR/PAUSA ; a luz fica laranja e intermitente para indicar que o programa está em pausa. Seleccione o novo programa e quaisquer opções necessárias e, de seguida, a luz ficará verde. Prima novamente o botão INICIAR/PAUSA e o novo programa é iniciado.
Roupa P Escolher a sua roupa Tempos de secagem • Consulte os símbolos nas etiquetas das roupas, de modo a certificar-se de que os artigos podem ser utilizados na secadora. • Escolha a roupa por tipo de tecido. • Esvazie os bolsos e verifique os botões. • Feche os fechos de correr e desaperte cintos e correias. • Torça cada peça de modo a eliminar o máximo de água possível. ! Não carregue peças a pingar na secadora. O quadro que se segue apresenta os tempos de secagem APROXIMADOS em minutos.
Resolução de problemas Um dia a sua máquina parece não querer funcionar. Antes de contactar o seu Centro de Serviços (ver Reparação), analise as seguintes sugestões de resolução de problemas: Problema: Causas possíveis / Solução: A secadora não inicia. ● ● ● ● ● ● ● P A ficha não está ligada à tomada, ou não está a fazer contacto. Ocorreu uma falha de energia. Há um fusível queimado. Experimente ligar outro aparelho à tomada.
Reparação P Antes de contactar o Centro de Serviços: ● ● Utilize o guia de resolução de problemas para ver se consegue resolver o problema (ver Resolução de problemas). Caso contrário, desligue a secadora e contacte o Centro de Serviço mais próximo. Peças sobressalentes Esta secadora é uma máquina complexa. Repará-la sozinha ou através de um técnico não autorizado pode provocar danos a uma ou mais pessoas, pode danificar a máquina e pode invalidar a garantia das peças sobressalentes.
Dados do produto… (Regulamento da UE 392/2012) Marca Hotpoint Ariston Modelos TCF87B P FTCF87B Capacidade nominal da lavagem de algodão para o programa padrão com carga máxima 8 kg Eficácia energética de classe B Consumo de energia anual ponderado (AEc) 559.8 kWh Consumo por ano, com base em 160 ciclos de secagem do programa para algodões padrão com cargas totais e parciais e o consumo dos modos de baixo consumo. O consumo de energia real por ciclo depende do modo de utilização do aparelho.
195129104.00 N 12/2014 - LION fpg .