HXB9.8LT HXB6.
8x Ø 8 x 40 1x 2x 2 3 4 5 ø 150-125mm ø 150mm 1x 2 1x 6x Ø 8 x 40 8x Ø 5 x 45 6x Ø 5 x 45 2x Ø 3,5 x 9,5 4x Ø 3,5 x 9,5
min.
2 3 = = x6 = 55 0m 65 m 0 = m m 4 5 Ø 8 mm x6 7 5 m m 6 4 x6 x2
8 9 1 2 3 10 x2 11 x2 12 13 ø 120 ø 150 5
14 15 x2 ø 3,5 x 9,5 ø 150 16 6 17
19 B A 18 20 1 3 4 2 Ø 8 mm 5 x4 7
21 1 2 3 x2 ø 3,5 x 9,5 8
Warnings ! Keep this manual for reference. If you sell, transfer or move the unit to another location, make sure to keep the manual with the product. ! Read the instructions carefully - they contain important installation, user and safety information. ! Do not tamper with the electrical or mechanical equipment of the product or its exhaust ducts.
• Strictly observe all local regulations in relation to the technical and safety measures to be employed in fumes extraction. • Clean the product frequently, inside and out (AT LEAST ONCE A MONTH, and in observance of the maintenance instruction given in this manual). • Failure to observe the hood cleaning and filter cleaning/replacement instructions can result in fires. • Never use the hood without its bulbs properly installed - electrocution hazard.
Installation The installation procedure is illustrated in the first pages of this manual. The installation must be done by a qualified technician. Electrical hook up The mains voltage must match that given on the ratings label inside the hood itself. If the hood has a power plug, connect the hood to an easily accessible regulatory power socket.
GB TBOX-LUCE controls Models with Touch control glass (basic) HXB9.8LT - HXB6.8LT Hood off The hood can be turned off manually by pressing the T1 button (ON/OFF). If the timer is set, the hood turns off automatically when the set time runs out. Models with Touch control glass + display (medium) T1 T2 T3 T4 (Only available in certain models) T5 T6 T7 T8 T1 motor ON/OFF When the button is pressed with the hood off, the first speed is set.
Antigrease and odour filter signal The antigrease (A) and/or odour (B) filters need cleaning/ replacing after a certain number of hours of use (the latter for filtering hoods only). The indicator light I1 on indicates that the antigrease filter is saturated, while the indicator light I2 on indicates that the odour filter is saturated (for hoods in filtering mode only). Press T5 + T4 for 3 seconds with the hood on to reset the counter.
GB - Manual calibration: (or upon request) is set in the configuration menu. This procedure is advised, and may be started, in case of malfunctioning of the sensor (which, for example, may occur in case of blackout while cooking or after a long time since the use).
Servicing the grease filter (A) The grease filter retains the particles of grease produced during cooking; it must be cleaned at least once a month with a non-aggressive detergent, either by hand or A with a low temperature, short dishwasher cycle. To extract the grease filter, pull the spring loaded handle. If washed in a dishwasher, the metal filter may change colour, but this does not affect its performance.
GB Replacing the bulbs Disconnect the unit from the mains and remove the grease filter. Caution! Make sure the bulbs are cool before touching them. 1. Extract the guard by prising it out with a small flat head screwdriver or something similar. 2. Replace the faulty bulb. Use only bulbs of the same type (for details, see the technical data in the following manual). 3. Refit the guard (push it in). Replacing the lights LED * The hood is fitted with a lighting system based on LED technology.
GB PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24 17
GB After Sales Service No one is better placed to care for your Hotpoint appliance during the course of its working life than us – the manufacturer. Essential Contact Information Hotpoint Service We are the largest service team in the country offering you access to 400 skilled telephone advisors and 1000 fully qualified engineers on call to ensure you receive fast, reliable, local service. UK: 08448 224 224 Republic of Ireland: 0818 313 413 www.hotpointservice.co.
Guarantee GB 12 months Parts and Labour Guarantee Your appliance has the benefit of our manufacturer’s guarantee, which covers the cost of breakdown repairs for twelve months from the date of purchase. This gives you the reassurance that if, within that time, your appliance is proven to be defective because of either workmanship or materials, we will, at our discretion, either repair or replace the appliance at no cost to you.
195111022.
