Instructions for use WASHER-DRYER ! GB English, 1 This symbol reminds you to read this booklet.
Installation GB ! Keep this instruction manual in a safe place for future reference. Should the appliance be sold, transferred or moved, make sure the instruction manual accompanies the Washer-dryer to inform the new owner as to its operation and features. ! Read these instructions carefully: they contain vital information on installation, use and safety. Unpacking and levelling Unpacking 1. Unpack the Washer-dryer. 2. Check whether the Washer-dryer has been damaged during transport.
Connecting the drain hose 65 - 100 cm Connect the drain hose, without bending it, to a draining duct or a wall drain situated between 65 and 100 cm from the floor; the supply voltage is included within the values indicated on the Technical details table (see page 5); GB the socket is compatible with the washing machine's plug. If this is not the case, replace the socket or the plug. Your appliance is now supplied with a 13 amp fused plug it can be plugged into a 13 amp socket for immediate use.
GB As the colours of the wires in the lead may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: Connect Green & Yellow wire to terminal marked E or coloured Green or Green & Yellow. or Connect Brown wire to terminal marked L or coloured Red. Connect Blue wire to terminal marked N or coloured Black. If a 13 amp plug (BS 1363) is used it must be fitted with a 13 amp fuse, either in the plug or adaptor or at the distribution board.
GB Technical data Model BHWD 149 Dimensions width 59.5 cm height 81,5 cm depth 54,5 cm Capacity from 1 to 7 kg for the wash programme from 1 to 5 kg for the drying programme Electrical connections please refer to the technical data plate fixed to the machine Water connections maximum pressure 1 MPa (10 bar) minimum pressure 0.05 MPa (0.
GB Instructions for the fitter Door Mounting Accessories (Fig. 1-2-3-4-5). Mounting the wooden panel onto the door and inserting the machine into cabinets: In the case where the machine must be shipped for final installation after the wooden panel has been mounted, we suggest leaving it in its original packaging. The packaging was designed to make it possible to mount the wooden panel onto the machine without removing it completely (see figures below).
Using the Drilling Template. - To trace the positions of the holes on the left-hand side of the panel, align the drilling template to the top left side of the panel using the lines traced on the extremities as a reference. - To trace the positions of the holes on the right-hand side of the panel, align the drilling template to the top right side of the panel. - Use an appropriately sized router to mill the holes for the two hinges, the rubber plug and the magnet.
Description of the Washer-dryer and starting a wash cycle GB Control panel WASH CYCLE PROGRESS indicator lights DRYING ON/OFF button WASH Detergent dispenser drawer Detergent dispenser drawer: used to dispense detergents and washing additives (see Detergents and laundry). ON/OFF button: switches the Washer-dryer on and off. WASH CYCLE knob: programmes the wash cycles. During the wash cycle, the knob does not move. FUNCTION buttons with indicator light: used to select the available functions.
Indicator lights The indicator lights provide important information. This is what they can tell you: Wash cycle phase indicator lights Once the desired wash cycle has been selected and has begun, the indicator lights switch on one by one to indicate which phase of the cycle is currently in progress.
Wash cycles Table of wash cycles Wash cycles GB Max. load Cycle Detergents Max. Max. (kg) duration temp. speed Drying Fabric Mini Mini (°C) (rpm) Normal Normal Wash load load softener Description of the wash cycle Essentials cycles 1 Cottons: extremely soiled whites. 1 Cottons (1): heavily soiled whites. 90° 1400 l l l 7 3 170 115 60° 1400 l l l 7 3 160 105 1 Cottons (2): lightly soiled whites. 2 Cotton: heavily soiled whites and resistant colours.
Personalisation Setting the temperature GB Turn the TEMPERATURE knob to set the wash temperature (see Table of wash cycles). The temperature may be lowered, or even set to a cold wash ( ). The Washer-dryer will automatically prevent you from selecting a temperature which is higher than the maximum value set for each wash cycle. Setting the drying cycle Table of Drying times Fabric Load type (guideline values) Max. Cupboard Henger Iron Turn the DRYING knob to set the desired drying type.
Detergents and laundry GB Detergent dispenser drawer Garments requiring special care Good washing results also depend on the correct dose of detergent: adding too much detergent will not necessarily result in a more efficient wash, and may in fact a build up on the inside of your appliance and contribute to environmental pollution.
Precautions and tips ! This Washer-dryer was designed and constructed in accordance with international safety regulations. The following information is provided for safety reasons and must therefore be read carefully. If the appliance has to be moved, work in a group of two or three people and handle it with the utmost care. Never try to do this alone, because the appliance is very heavy. General safety Before loading laundry into the Washer-dryer, make sure the drum is empty.
Care and maintenance GB Cutting off the water and electricity supplies Turn off the water tap after every wash cycle. This will limit wear on the hydraulic system inside the Washer-dryer and help to prevent leaks. Unplug the Washer-dryer when cleaning it and during all maintenance work. To access the pre-chamber: 1. unscrew the lid by rotating it anticlockwise (see figure): a little water may trickle out.
Troubleshooting Your Washer-dryer could fail to work. Before contacting the Technical Assistance Centre (see Assistance), make sure that the problem cannot be not solved easily using the following list. GB Problem Possible causes/Solution: The machine does not switch on. The appliance is not plugged into the socket fully, or not enough to make contact. There is no power to the socket, or the fuse has blown in the mains plug. The wash cycle does not start. The machine does not dry.
GB The machine is noisy. There will always be some motor, pump and drum noise during spin. The machine wont spin p r o p e r l y. Out of Balance detected when attempting to go into a spin cycle If this happens the machine will continue to try to repeat the distribution of the load required before the machine will go into higher spin speeds - This will increase the programme time accordingly. This is a safety feature to prevent damage.
Assistance Guarantee GB 12 Months Parts and Labour Guarantee Your appliance has the benefit of our manufacturers guarantee, which covers the cost of breakdown repairs for twelve months from the date of purchase. This gives you the reassurance that if, within that time, your appliance is proven to be defective because of either workmanship or materials, we will, at our discretion, either repair or replace the appliance at no cost to you.
After Sales Service GB No one is better placed to care for your Hotpoint appliance during the course of its working life than us - the manufacturer. Essential Contact Information Hotpoint Service We are the largest service team in Europe offering you access to 400 skilled telephone advisors and 1000 fully qualified engineers on call to ensure you receive fast, reliable, local service. UK: 08448 224 224 Republic of Ireland: 0818 313 413 www.hotpointservice.co.
GB '
195081686.