Instructions for use WASHER DRYER ! This symbol reminds you to read this instruction manual.
Installation GB ! Keep this instruction manual in a safe place for future reference. Should the appliance be sold, transferred or moved, make sure the instruction manual accompanies the washing machine to inform the new owner as to its operation and features. ! Read these instructions carefully: they contain vital information on installation, use and safety. Unpacking and levelling Unpacking ! This is a separate part of the polystyrene base and should be removed with the base.
• the supply voltage is included within the values indicated on the Technical Data Plate fixed on the machine. Connecting the drain hose 65 - 100 cm Where it connects to the waste water pipe cut end off spigot or remove the blanking cap Connect the drain hose, without bending it, to a draining duct or a wall drain situated between 65 and 100 cm from the floor; The drain hose may be connected to an undersink trap.
GB As the colours of the wires in the lead may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: Connect Green & Yellow wire to terminal marked E or or coloured Green or Green & Yellow. Connect Brown wire to terminal marked L or coloured Red. Connect Blue wire to terminal marked N or coloured Black. If a 13 amp plug (BS 1363) is used it must be fitted with a 13 amp fuse, either in the plug or adaptor or at the distribution board.
GB Technical data Model WDD 960 P/G/A/K Dimensions width 59.5 cm height 85 cm depth 53.5 cm Capacity from 1 to 7 kg for the wash programme from 1 to 5 kg for the drying programme Electrical connections please refer to the technical data plate fixed to the machine Water connections maximum pressure 1 MPa (10 bar) minimum pressure 0.05 MPa (0.
Description of the washer dryer GB Control panel CHILD LOCK button ON/OFF DRYING button button SPIN SPEED button DISPLAY Detergent dispenser drawer WASH CYCLE SELECTOR buttons Detergent dispenser drawer: used to dispense detergents and washing additives (see “Detergents and laundry”). ON/OFF button : press this briefly to switch the machine on or off. The START/PAUSE indicator light, which flashes slowly in a green colour shows that the machine is switched on.
Display GB Z B A F X D C E Y F F L The display is useful when programming the machine and provides a great deal of information. The upper two strings A and B are used to display the selected wash cycle or the type of drying selected, the current wash cycle phase (the selected dryness level or drying time) and all the indications relating to the progress status of the cycle.
How to run a wash cycle or a drying cycle GB 1. SWITCH THE MACHINE ON. Press the button; the text HELLO will appear on the display and the START/PAUSE indicator light will flash slowly in a green colour. 2. LOAD THE LAUNDRY. Open the porthole door. Load the laundry, making sure you do not exceed the maximum load value indicated in the table of programmes on the following page. 3. MEASURE OUT THE DETERGENT.
Wash cycles and functions Wash cycles Table of wash cycles Detergents Description of the wash cycle GB Max. load (kg) Max. Max. Cycle temp. speed Drying duration Fabric Mini (°C) (rpm) Wash softener Normal load Everyday wash cycles (Daily) 90° 1600 7 3 Cottons: heavily soiled whites and resistant colours. 60° 1600 7 3 Cottons (**): lightly soiled whites and delicate colours. 40° 1600 7 3 Synthetics (1st press of the button): heavily soiled resistant colours.
Detergents and laundry GB Detergent dispenser drawer Garments requiring special care Good washing results also depend on the correct dose of detergent: adding too much detergent will not necessarily result in a more efficient wash, and may in fact cause build up on the inside of your appliance and contribute to environmental pollution. Curtains: fold curtains and place them in a pillow case or mesh bag. Use wash cycle .
Precautions and tips ! This Washer-dryer was designed and constructed in accordance with international safety regulations. The following information is provided for safety reasons and must therefore be read carefully.
Care and maintenance GB Cutting off the water and electricity supplies • Turn off the water tap after every wash cycle. This will limit wear on the hydraulic system inside the washer dryer and help to prevent leaks. 2. unscrew the lid by rotating it anti-clockwise (see figure): a little water may trickle out. This is perfectly normal; • Unplug the washer dryer when cleaning it and during all maintenance work.
Troubleshooting Your washer dryer could fail to work. Before contacting the Technical Assistance Centre (see “Assistance”), make sure that the problem cannot be not solved easily using the following list. GB Problem: Possible causes / Solutions: The machine does not switch on. • The appliance is not plugged into the socket fully, or not enough to make contact. • There is no power to the socket, or the fuse has blown in the mains plug. The wash cycle does not start.
GB The machine vibrates a lot during the spin cycle. • The feet have not been adjusted, enabling the machine to rock. • New Installation - Either the Transit Bolts including the plastic spacers, or the Polystyrene Packaging have not been removed when installing the machine. • The machine is trapped between cabinets and/or walls. • The load is in a slight out of balance condition and machine is spinning, but at a lower speed. The machine is noisy.
Assistance Guarantee GB 12 Months Parts and Labour Guarantee Your appliance has the benefit of our manufacturer’s guarantee, which covers the cost of breakdown repairs for twelve months from the date of purchase. This gives you the reassurance that if, within that time, your appliance is proven to be defective because of either workmanship or materials, we will, at our discretion, either repair or replace the appliance at no cost to you.
195081735.06 02/2012 - Xerox Fabriano After Sales Service GB No one is better placed to care for your Hotpoint appliance during the course of its working life than us - the manufacturer. Essential Contact Information Hotpoint Service We are the largest service team in Europe offering you access to 400 skilled telephone advisors and 1000 fully qualified engineers on call to ensure you receive fast, reliable, local service. UK: 08448 224 224 Republic of Ireland: 0818 313 413 www.hotpointservice.co.