965B, 1075BE, 1080BE OPERATOR’S MANUAL 1.110-565.0 1.110-566.0 1.110-567.0 C 89312360-1 LIS T E D ® For technical assistance or the hotsy dealer nearest you, consult our web page at www.hotsy.com 8.931-236.
1075BE (1.110-566.0) SPECIFICATIONS 1080BE (1.110-567.0) SPECIFICATIONS Pump Volume At Pump Head: 3.8 GPM Pump Pressure At Pump Head: 3500 PSI Burner Type: Fuel Oil Fired / 385,800 BTU/HR Burner Fuel Pressure: 150 PSI Burner Exhaust Stack: 8" Machine Power: Honda GX390 Machine Weight: 560 Lbs. Shipping Weight: 650 Lbs. Machine Dimensions: Pump Volume At Pump Head: 4.
CONTENTS Introduction & Important Safety Information 5-7 Component Identification 8 Assembly Instructions 9 Installation 10-11 Operation Instructions 12 Detergents & General Washing Techniques 13 Shut Down Instructions & Storage 14 Maintenance 15 Troubleshooting Guide 16-17 7ARRANTY Model Number ______________________________ Serial Number ______________________________ Date of Purchase ____________________________ The model and serial numbers will be found on a decal attached to the pres
Thank you for purchasing this Pressure Washer. We reserve the right to make changes at any time without incurring any obligation. WARNING WARNING: This machine exceeds 85 db appropriate ear protection must be worn. Owner/User Responsibility: Owner and/or user must study and maintain for future reference the manufacturers’ instructions. The operator must know how to stop the machine quickly and understand the operation of all controls.
PRESSURE WASHER OPERATOR’S MANUAL IMPORTANT SAFETY INFORMATION In an overfilling situation, additional precautions are necessary to ensure that the situation is handled in a safe manner. WARNING: Risk of injury. Disconnect battery ground terminal before servicing. 8. When in use , do not place machine near flammable objects as the engine is hot. 9. Oil burning appliances shall be installed only in locations where combustible dusts and flammable gases or vapors are not present.
OPERATOR’S MANUAL 21. Do not allow acids, caustic or abrasive fluids to pass through the pump. 22. Never run pump dry or leave spray gun closed longer than 1-2 minutes. 23. Machines with shut-off spray gun should not be operated with the spray gun in the off position for extensive periods of time as this may cause damage to the pump. 24. Protect discharge hose from vehicle traffic and sharp objects. Inspect condition of high pressure hose before using or bodily injury may result. 25.
PRESSURE WASHER COMPONENT IDENTIFICATION OPERATOR’S MANUAL Burner Exhaust Relief Valve Pump Unloader Valve Engine Control Box Fuel Oil Tank Spray Gun Gasoline Tank Spray Wand 8931230-2 High Pressure Hose Pump — Delivers a specific gpm to the high pressure nozzle which develops pressure. Spray Gun — Controls the application of water and detergent onto cleaning surface with trigger device. Includes safety latch.
2. Assemble wand components as shown in Figure 4. Unpacking Unpack carefully. Wear safety glasses or goggles while unpacking, assembling, or operating pressure washer. If there are missing components or hidden damage, immediately contact carrier concerning discrepancies. Wand Parts Included Pressure Washer Pressure Hose Pressure Nozzles (3 Ea.) Wand Trigger Gun Operations Manual Gasoline Engine Manual Spray Gun High Pressure Hose Figure 4 - Trigger Gun/Wand Assembly 3.
PRESSURE WASHER OPERATOR’S MANUAL INSTALLATION Getting Started Battery IMPORTANT: Proper initial installation of equipment will assure more satisfactory performance, longer service life, and lower maintenance cost. WARNING: Batteries generate explosive gases during normal battery operation. DO NOT expose the battery to flame or sparks as these gases may ignite. IMPORTANT: The use of backflow preventer on the water supply hose is recommended and may be required by local code.
Beckett Oil Burner To adjust, start machine and turn burner ON (refer to Operation for details). Loosen two locking screws found in the air shutter openings (refer to Figure 6) and close air shutter until black smoke appears from burner exhaust vent. Note air band position. Next, slowly open the air shutter until white smoke just starts to appear. Turn air shutter halfway back to the black smoke position previously noted. Tighten locking screws. To adjust, start machine and turn burner ON.
PRESSURE WASHER OPERATOR’S MANUAL OPERATION INSTRUCTIONS Before Starting To Start WARNING: Check hoses, fittings, wand, trigger gun and fuel connections daily for signs of wear, cracks and looseness, replace as required. DANGER: DO NOT point wand or spray gun at yourself or at any person. Bodily injury may result from water under high pressure. 1. Read all manuals provided with this pressure washer. Become familiar with location and function of all operating and safety controls. 2.
WARNING STEP 1: Use detergent designed specifically for pressure washers. Household detergents could damage the pump. Prepare detergent solution as required by the manufacturer. Fill a container with pressure washer detergent. Place the filter end of detergent suction tube into the detergent container. STEP 2: With the engine running, pull trigger to operate machine. Liquid detergent is drawn into the machine and mixed with water. Apply detergent to work area. Do not allow detergent to dry on surface.
PRESSURE WASHER OPERATOR’S MANUAL SHUTDOWN INSTRUCTIONS & STORAGE 1. If detergents were used, draw clear water through the system to purge detergent. 2. If burner was used, turn OFF burner switch, and allow pump to run cold water through coil. 3. Move throttle control to idle position. 4. Turn key on engine counterclockwise (CCW) to OFF position. 5. Turn OFF fuel shut-off valve. 6. Turn OFF water supply. 7. Squeeze trigger gun open to relieve system pressure.
WARNING: Unauthorized machine modification or use of non-approved replacement parts may cause personal injury and/or property damage and will void the manufacturer warranty. Drain water that has accumulated in fuel filter and clean filter element as needed. Heating Coil Pump DO NOT: Pump acids. Fail to winterize in freezing temperatures. Allow pump to run dry. Allow machine to run with trigger gun closed for more than 3 minutes at any one time or damage to pump may occur.
PRESSURE WASHER Troubleshooting Guide TROUBLESHOOTING SYMPTOM POSSIBLE CAUSES CORRECTIVE ACTION ENGINE WILL NOT RUN No fuel Replenish supply. Low battery Charge battery. Poor battery cable connection Clean battery terminals and check cables. Refer to provided engine manual for additional troubleshooting NO WATER FROM PRESSURE NOZZLE Pressure nozzle clogged Clean pressure nozzle. Inlet water screen clogged Clean. Pump sucking air Fill the detergent container.
IMPORTANT If the pressure washer demonstrates other symptoms or the corrective actions listed do not correct the problem, contact the local authorized Hotsy Service Center. The Hotsy Service Center can be identified by visiting www.hotsy.com .
HOTSY LIMITED NEW PRODUCT WARRANTY PRESSURE WASHERS WHAT THIS WARRANTY COVERS All Hotsy pressure washers are warranted by Hotsy to the original purchaser to be free from defects in materials and workmanship under normal use, for the periods specified below. This Limited Warranty is subject to the exclusions shown below, is calculated from the date of the original purchase, and applies to the original components only.
If you are looking for replacement parts for your Hotsy, please contact your local dealer. You can find a dealer by calling Hotsy at 800-525-1976 or by visiting www.hotsy.com.
8.931-236.0 • Revised 6/11 • Printed in U.S.A.
