Assembly Instruction

ManualsBrandsHouse of Hampton ManualsCeiling LightsMccaulley 5 - Light Unique / Statement Drum Chandelier

1of4

(5)A19MediumBaseBulbs100WMaximum.

30-45minutes

Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare

present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement

parts.

LightSource:

EstimatedAssembly Time:

Preparation:

ToolsRequired:Flatheadscrewdriver, Phillips screwdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.

Note:This CONVERTIBLEfixturecanbemountedaspendantlightorsemi-flushlight.Refertorespective

installationsteps forinstallations.

Warnings and Cautions

Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.

These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly

recommend that a licensed, professional electrician perform the installation.

Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.

Assembly Instructions for Pendant Light

(Step 1A - Step 8A)

Package Contents

Crossbar Assembly

Ceiling Canopy

STEP 3A Tighten the Swivel to Ceiling Canopy-

A. By using pliers, tight the hex nut inside of the ceiling canopy until

snug to secure the swivel to the ceiling canopy.

Figure 1A

6” Rod

12” Rod

Fixture Body

Diffuser

Stem

Hex Nut

Finial

Hex Nut

Ceiling

Canopy

Swivel

STEP 1A - Installing the Crossbar Assembly

A. Pass the supply wires from outlet box through the Crossbar

Assembly (A). Attach the Crossbar Assembly (A) to the Outlet Box

with the head of the Green Ground Screw facing you. Secure the

Crossbar Assembly (A) with Outlet Box Screws (not included).

Tighten until snug.

Figure 2A

Supply Wires with

Ground Wire

Outlet Box Screws

(not included)

Outlet Box

STEP 2A - Test Fitting Ceiling Canopy to Crossbar Assembly

A. Remove mounting balls from the Crossbar Assembly (A). Fit the

Ceiling Canopy (B) to the Crossbar Assembly (A) and secure with

mounting balls. Note: The ceiling canopy should be snug against the

ceiling and the mounting balls. If not, adjust the length of the nipple

on the Crossbar Assembly (A) by unscrewing the preassembled hex

nut and lock washer and then screwing the mounting screws in or

Mounting Screw

Hex Nut and

Lock Washer

Mounting Ball

Figure 3A

(Step 2A Continued)

out of the crossbar until the correct length is achieved. Once the

Ceiling Canopy (B) is secure, remove the mounting ball and Ceiling

Canopy (B) and proceed to Step 3A.

Big Crystal

Small Crystal

Spare Part

Assembly Instruction Sheet

Summary of content (4 pages)

PAGE 1
Assembly Instruction Sheet Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses. Light Source: (5) A19 Medium Base Bulbs 100W Maximum. Estimated Assembly Time: 30-45 minutes Preparation: Identify and inspect all parts before beginning installation. Check package content list and diagrams below to be sure all parts are present. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture.
PAGE 2
STEP 4A - Install the Diffuser STEP 7A - Install Fixture to Ceiling A. Thread the Stem (F) onto the nipple on the bottom center of the junction box and hand tighten until snug. B. Place the Diffuser (G) over the end of the Stem (F) and secure with the Hex Nut (H). Tighten until snug. C. Thread the Finial (I) onto the Stem (F) and hand tighten until snug. A. Carefully tuck all wires into the outlet box and position the Ceiling Canopy (B) over the outlet box.
PAGE 3
(Step 2B Continued) STEP 5B - Wire Connections ceiling and the mounting balls. If not, adjust the length of the nipple on the Crossbar Assembly (A) by unscrewing the preassembled hex nut and lock washer and then screwing the mounting screws in or out of the crossbar until the correct length is achieved. Once the Ceiling Canopy (B) is secure, remove the mounting ball and Ceiling Canopy (B) and proceed to Step 3B. A. Use standard wire connectors (not included) to make all wire connections.
PAGE 4
NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/4" FINISH: VINTAGE GOLD PENDANT LIGHT 5” Dia. 48” OVERALL HEIGHT INCLUDES (2) 6” RODS AND (2) 12” RODS 9” 20” Dia. SEMI-FLUSH 5” Dia. 9.5” 20” Dia.