USER MANUAL IN-100CM Keep this manual in the vehicle for future reference. Read this manual before using this product. Failure to follow the instructions and safety precautions in this manual may result in serious injury or death.
IMPORTANT SAFETY INFORMATION The Halo Connect Gateway and its components should be installed and maintained in accordance with the instructions in this manual. Proper installation of the Halo Connect is critical to ensure safe use of the device. Failure to do so may result in injury or death, damage to equipment, material or property. Carefully read, understand and follow all safety related information within this manual. Exercise caution when working with the vehicle power sources to avoid inury.
Contents 2 2 2 Safety Important Safety Information Safety Words and Symbols 4 Introduction 5 5 5 Getting Started System Components Installation Tools 6 6 7 8 8 9 9 9 10 10 Halo Connect Installation Determine where to put the Gateway Locate power source and ground Attach TPMS antenna to vehicle Attach GPS antenna to vehicle Attach Gateway to vehicle Connect cables to Gateway Confirm Gateway power Install TPMS sensors Pair Gateway using mobile app 11 Regulatory Customer Support Phone +1 (650) 74
SYSTEM Halo Connect Web Services Web Services give you full control over your data, alerts, and reports. All of the issues in the fleet, active and historical, are easily viewed and organized, using the systems that fleets are most comfortable with, such as email. For each vehicle issue, the portal gives recommended actions for resolution. For an understanding of the bigger picture, we distill the data into analytical reports to visualize the trends in the fleet.
Getting started SYSTEM COMPONENTS HALO Connect Gateway • Pack of Halo Connect sensors • Power cable with mini fuse connector • TPMS cable • TPMS antenna • Cellular antenna • GPS antenna INSTALLATION TOOLS • 5/16" Hex Head Screwdriver • Torx Screwdriver (or Other, as needed, to access fuse panel) • Wire Crimper • Cutters (for cutting zip ties) • Isopropyl Alcohol and Wipes MOUNTING PARTS • #10 x 1" Hex Head Screws (5/16" Hex Head) • UV Stabilized 6" Zipties • 1" x 1" Velcro squ
8 6 HALO CONNECT INSTALLATION 1. Determine where to put Gateway Select a location to permanently attach the Gateway box inside the cab of the vehicle. Consider that the Gateway will have power and antenna cables attached to it that need to be routed to locations specified in later steps. See step 5 for further instructions on attaching the Gateway to the vehicle.
HALO CONNECT INSTALLATION, CONT'D 2. locate power source and ground In order for the vehicle's tires to be monitored 24 hours, the Gateway power cable should be connected to a 24 hour continous 12-20V power source and be securely grounded to the vehicle chassis. A mini add-a-fuse connector is included with the Gateway. If using this add-a-fuse, locate the vehicle's fuse box and select the power and ground locations.
HALO CONNECT INSTALLATION, cont'd 3. attach TPMS antenna to vehicle The TPMS antenna must be placed outside on the rear of the vehicle and the cable needs to be routed back to the Gateway. Find an opening in the cab to route the antenna cable from the Gateway to the outside of the vehicle. Once the cable is routed, attach the TPMS antenna to the end of the TPMS antenna cable and securely attach the TPMS antenna to the outside of the vehicle using at least two zip ties.
HALO CONNECT INSTALLATION, cont'd 5. Connect cables to gateway On the gateway, the side label marks the port for each of the cables, as seen below: ON/OFF ANTENNAS Ensure the cables are securely attached to the Gateway to avoid loosening due to vibration during vehicle operation. 6. Attach Gateway to vehicle Use the included mounting screws and a 5/16" socket to securely attach the Gateway in the location selected in step 1.
9. install TPMS Sensors Locate the sensor pack. Each sensor has a label that specifies which valve stem the sensor must be screwed onto. R2 INNER How to Read Tire Position Label This sensor should be installed on: R = Right side of vehicle (from driver perspective) 2 = 2nd Axle (steer tire is axle 1) Inner = Inner tire position Screw each sensor onto the correct valve stem. Sensors for Halo equipped tires should be attached to the Halo hose.
Regulatory RF Exposure This equipment complies with FCC and IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Cet équipement est conforme aux limites d'exposition aux radiations de la FCC et de l'IC définies pour un environnement non contrôlé.
QTY: 1 Part Number: IN-100CM Description: User Manual, Halo Connect Aperia Technologies, Inc. 1616 Rollins Rd. Burlingame, CA 91040 Phone: (650) 741-3231 Fax: (415) 524-2449 www.aperiatech.com © 2019 Aperia Technologies, Inc. IN-100CM 91-00006672 Rev. R02 PMN: Halo Connect Gateway Model No.: GW-10 (for xBR type sub-1GHz Rx) Model No.
