z TM Bio SpeedCLEAN VX200 u u u u z Model No.
z z INSTRUCTIONS u PLEASE CAREFULLY READ THIS MANUAL BEFORE OPERATING THIS MACHINE Do not use this vacuum to clean up liquids such as water, detergent or other wet fluids. u Do not use this vacuum to clean up small granules such as flour, cement or plaster powder or large objects such as toys or balls of paper. That will cause the vacuum to become blocked and overheat. Use a damp cloth with mild detergent to clean the outside of this machine.
ON/OFF BUTTON SPEED CONTROL BUTTON u CHARGING NEEDLE PORT DUST CUP ASSEMBLY RELEASE BUTTON CHARGING INDICATOR LIGHT MOTOR RELEASE BUTTON DUST CUP ASSEMBLY DUST CUP RELEASE BUTTON z VACUUM TUBE RELEASE BUTTON MOTORIZED FLOOR BRUSH UV LIGHT
u ON/OFF BUTTON WALL MOUNT HANDLE BATTERY UNIT u DUST CUP RELEASE MINI MOTORIZED BRUSH CHARGING CORD 2-IN-1 UPHOLSTERY BRUSH LONG CREVICE TOOL
z PARTS ASSEMBLY u u Battery Unit Insert the battery unit into the bottom of the motor. When it is locked into the motor, you will hear it click. u Dust Cup Insert the lower plastic clip into the hole on the motor. Then snap the upper cover with the upper release button on the motor. Snap the Dust Cup in place, then press down on the upper and lower release button to lock the cup into place.
z u u Connection of Vacuum Tube and Motorized Floor Brush Insert the upper end of the Motorized Floor Brush into the lower connection of the Vacuum Tube until you hear it click in and lock into place. u u Connection of the Motor and the Vacuum Tube Insert the upper end of the Vacuum Tube in to the main hole of the Motor below the Dust Cup until you hear it click in and lock into place.
u Connection of the Mini Motorized Brush and the Motor Insert the upper part of the Mini Motorized Brush into the main hole of the Motor below the Dust Cup until you hear it click in and lock into place. u Connection of accessory pieces to the Motor Insert the accessory brushes into the main hole of the motor below the Dust Cup until you hear them click in and lock into place.
u Connection of the Vacuum Tube with the accessory pieces Insert the accessory brushes into the bottom of the Vacuum Tube until you hear them click and lock into place. z WALL MOUNT Attach wall mount to a wall using the screws and anchors that are included. Flip the wall mount handle on the main vacuum unit down to allow the unit to hang onto the wall mount.
z USES u Low Speed, High Speed, Off Press the Speed Control Button once to turn the unit on. Press it again to turn the unit off. Use the Speed Control Button to switch the speed between low and high by touching the + or – on the button. u Use of 2-in-1 Upholstery Brush 1. Insert the 2-in-1 Upholstery Brush into the hole below the Dust Cup Assembly, then push out the brush head of the 2-in-1 Upholstery Brush by pressing the button and pushing the brush out at the same time.
z CLEANING THE UNIT u Clean Dust Cup after each use Press the upper button on the Motor to release the Dust Cup Assembly Unit, then press the lower button to release the Dust Cup Lower Cover. u Dust Cup Cleaning A. Press the button at the bottom of the Dust Cup to release the Lower Cover of the Dust Cup to empty it. B. Hold the Dust Cup with one hand, and use your other hand to open the top of the Dust Cup counterclockwise and take the upper part off the Dust Cup. C.
z TROUBLESHOOTING TIPS u If there is no power/the machine doesn’t turn on, it will need to be charged. u If the bristles are not rotating, they will need to be cleaned. u If you are charging the battery and the charging light isn’t on, the cord may not be inserted properly into the charging port. Try pushing it in farther. u If the battery won’t hold a charge, you may need a replacement battery. Go to www.edenpuresupport.com to purchase one. z PRODUCT SPECIFICATIONS Model Number A5969 Volts 22.
