HP StorageWorks 2012i Modular Smart Array user guide Part number: 481598-001 First edition: March, 2008
Legal and notice information © Copyright 2008 Hewlett-Packard Development Company, L.P. Hewlett-Packard Company makes no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Hewlett-Packard shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material.
Contents About This Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 Intended Audience . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 Prerequisites . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 Document Conventions Rack Stability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2. Installing and Cabling Enclosures Required Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Installing Enclosures Into a Rack Preparing the Rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 . . . . . .
4. Configuring a System for the First Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Setting Management Port IP Addresses Using the CLI Configuring Your Web Browser for SMU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 Logging in to SMU from a Local Management Host Updating Firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 Configuring Controller Enclosure Host Ports Configuring Data Host Ethernet Ports . .
HP StorageWorks 2012i Modular Smart Array user guide • March 2008
About This Guide Intended Audience This guide is intended for use by system administrators and information professionals who are experienced with the following: ■ Direct attach storage (DAS) or storage area network (SAN) management ■ Network administration ■ Network installation ■ Storage system installation and configuration, including installing an HP rack Prerequisites Prerequisites for installing and configuring this product include familiarity with: ■ Servers and computer networks ■ Fibre Channel, iS
Document Conventions Typeface Meaning Examples AaBbCc123 Book title, new term, or emphasized word See the Release Notes. A virtual disk (vdisk) can .... You must be an advanced user to .... AaBbCc123 Directory or file name, value, command, or on-screen output The default file name is store.logs. The default IP address is 10.0.0.1. Type exit.
HP Technical Support Telephone numbers for worldwide technical support are listed on the HP support website: http://www.hp.com/support/. Collect the following information before calling: Technical support registration number (if applicable) ■ Product serial numbers ■ Product model names and numbers ■ Applicable error messages ■ Operating system type and revision level ■ Detailed, specific questions ■ For continuous quality improvement, calls may be recorded or monitored.
Subscription Service HP strongly recommends that customers sign up online using the Subscriber's choice website: http://www.hp.com/go/e-updates. Subscribing to this service provides you with e-mail updates on the latest product enhancements, newest versions of drivers, and firmware documentation updates as well as instant access to numerous other product resources. HP Websites For other product information, see the following HP websites: ■ ■ ■ ■ ■ http://www.hp.com http://www.hp.com/go/storage http://www.
CH A P T E R 1 Before You Begin The MSA2000 Family 2012i Modular Smart Array and MSA2000 Drive Enclosure are high-performance storage solutions that combine outstanding performance with high reliability, availability, flexibility, and manageability. Supported configurations include a controller enclosure with or without attached drive enclosures. A controller enclosure can contain two controllers that interact and provide failover capability for the data path.
System Management Software Embedded management software includes a web-browser interface and the command-line interface described below. HP StorageWorks MSA2000 Family Storage Management Utility (SMU) SMU is the primary interface for configuring and managing the system. A web server resides in each controller module. SMU enables you to manage the system from a web browser that is properly configured and that can access a controller module through an Ethernet connection.
Hardware Components and LEDs This section describes the main hardware components of your storage system enclosures. Controller Components and LEDs The controller enclosure can be connected through switches to Ethernet adapters (NICs) or host iSCSI ports. Table 1-1 describes the enclosure components.
Figure 1-1 shows the components and LEDs on the front of a controller. Enclosure ID Drive module LEDs (top to bottom) Fault/UID Online/Activity Status LEDs (top to bottom): UID Fault ID Heartbeat Drive modules are numbered by column top to bottom: 0–2, 3–5, 6–8, 9–11 Figure 1-1 Controller (Front View) Table 1-2 describes the LEDs on the front of a controller.
Table 1-3 describes the LEDs on the drive module. Table 1-3 Drive Module LED Combinations (Front) Online/Activity (green) Fault/UID (amber/blue) Description On Off The drive is online, but it is not currently active. Blinking irregularly Off The drive is active and operating normally. Off Amber, blinking regularly (1 Hz) Offline; the drive is not being accessed. A predictive failure alert has been received for this device. Further investigation is required.
Figure 1-2 shows the ports and switches at the back of the controller.
Figure 1-3 shows the LEDs at the back of the controller.
Table 1-5 Controller LEDs (Back) (Continued) Location Controller module Controller module Controller module Controller module Controller module Controller module Controller module Controller module Controller module 18 LED Unit Locator OK to Remove Fault/Service Required OK Cache status Host activity Ethernet link status Ethernet activity Expansion port status Color State Description White Off Normal operation. Blink Physically identifies the controller module.
Drive Enclosure Components and LEDs A drive enclosure can be connected to a controller enclosure or to another drive enclosure to provide additional disk storage capacity. Table 1-6 describes the drive enclosure components.
Figure 1-4 shows the ports and switches at the back of the drive enclosure. Power switch 0 0 Service 0 0 Service SAS In port Service port SAS Out port Figure 1-4 Drive Enclosure Ports and Switches (Back View) Table 1-7 describes the ports and switches on the back of the drive enclosure.
Figure 1-5 shows the LEDs at the back of the drive enclosure. AC Power Good DC Voltage/Fan Fault/ Service Required SAS In port status 0 SAS Out port status 0 Service 0 0 Service Unit Locator OK OK to Remove Fault/Service Required Figure 1-5 Drive Enclosure LEDs (Back View) Table 1-8 describes the LEDs on the back of the drive enclosure.
Table 1-8 Drive Enclosure LEDs (Back) (Continued) Location Expansion module Expansion module Expansion module 22 LED Fault/Service Required OK SAS Out port status Color State Description Amber On A fault has been detected or a service action is required. Blink Indicates a hardware-controlled power up or a cache flush or restore error. Off Expansion module is not OK. On Expansion module is operating normally. Blink System is booting. Off The port is empty or the link is down.
Installation Checklist Table 1-9 outlines the steps required to install the enclosures and initially configure the system. To ensure a successful installation, perform the tasks in the order they are presented. Table 1-9 Installation Checklist Step Installation Task Where to Find Procedure 1. Prepare the rack for installation. “Preparing the Rack” on page 27 2. Install the controller enclosure and optional drive enclosures in the rack. “Rack Installation Overview and Procedure” on page 28 3.
Table 1-9 Installation Checklist (Continued) Step Installation Task Where to Find Procedure 9. Connect the data hosts. “Connecting Hosts” on page 39 10. Connect the management host. “Connecting Remote Management Hosts” on page 43 11.
CH A P T E R 2 Installing and Cabling Enclosures This chapter describes how to install and cable enclosures in a standard 19-inch EIA rack cabinet.
Safety Precautions For your protection, observe the following safety precautions when setting up your equipment: ■ Follow all cautions and instructions marked on the equipment. ■ Ensure that the voltage and frequency of your power source match the voltage and frequency inscribed on the equipment’s electrical rating label. ■ Never push objects of any kind through openings in the equipment. Dangerous voltages may be present.
Installing Enclosures Into a Rack This section describes how to install the enclosures into a standard 19-inch rack cabinet with a 28 to 36-inch (71.12 to 91.44-cm) depth. Note – Keep all hardware items in plastic bags until you are ready to use them. This enables you to correctly identify the screws and avoid confusion.
Rack Installation Overview and Procedure Figure 2-1 provides a visual overview of rack installation and components and corresponds to the steps that follow. #10-32 x 5/8-in. Truss screws (Step 6) #10-32 x 5/8-in. Truss screws (Step 9) Rear bracket connected to rack Threaded PEMs (4) Side bracket #8-32 x 3/16-in. flathead screws (Step 5) #8-32 x 1/4-in.
Use the following procedure and refer to Figure 2-1 to install each enclosure into the rack. When positioning an enclosure in the rack, do not block the air vents at the front or back of the enclosure. Caution – If you only have one person to perform the installation, remove the power and cooling modules and drive modules from an enclosure before installation, and use the optional nylon front support brackets.
Figure 2-2 Side Bracket With Alignment Marks b. On one side, insert the first two screws through the side bracket slots above and below the alignment mark into the rear-most threaded holes in the enclosure. For example, to mount the enclosure in a 28-inch deep rack, position the side bracket so that the 28-inch alignment mark is aligned with the rear-most threaded holes in the enclosure. c.
Attaching the Ear Caps The plastic ear caps are snap-on parts that require some care when attaching or removing them. After the enclosure has been installed in the rack cabinet, attach the ear caps, which are located in a plastic bag included in the controller enclosure package. 1. Remove the ear caps from the plastic package. 2. As you attach each ear cap, hold it so that its indent is closest to the chassis. Indent Left ear cap Indent Right ear cap Figure 2-3 Ear Caps 3.
Connecting Controller and Drive Enclosures Use the supplied SAS cables to connect a controller enclosure to up to three drive enclosures. Figure 2-4 and Figure 2-5 show the recommended fault-tolerant cabling patterns. In an enclosure, the upper module is designated A and the lower module is designated B. When connecting multiple drive enclosures, use reverse cabling to ensure the highest level of fault tolerance.
Controller A Controller B 1A In Out In Out In Out 2A In Out 2B In Out 3A In Out 3B 1B Figure 2-5 Fault-Tolerant Cabling Connections Between One Controller Enclosure and Up to Three Drive Enclosures Chapter 2 Installing and Cabling Enclosures 33
Controller A Controller B In Out 1A In Out 1B In Out 2A In Out 2B In Out In Out 3A 3B Figure 2-6 Non-Fault-Tolerant Cabling Connections Between One Controller and Up to Three Drive Enclosures 34 HP StorageWorks 2012i Modular Smart Array user guide • March 2008
Connecting AC Power Use this procedure to connect AC power to the enclosures. 1. Verify that both power switches are off. 2. Using the AC power cords, for each enclosure, connect one power and cooling module to one power source in the rack, and the other power and cooling module to a separate power source in the rack. 3. Connect the primary power cords from the rack to separate external power sources. Power on the system as described in the topic that follows.
Testing the Enclosure Connections Use this procedure to power on the newly installed system. 1. Press the power switches at the back of each drive enclosure to the On (–) position. This ensures that the disks in the drive enclosures have enough time to completely spin up before being scanned by the RAID modules in the controller enclosure. Depending on your configuration, it can take several minutes for the system to power up. While enclosures power up, their LEDs blink.
Obtaining IP Values for Your Storage System Use the guidelines presented in this section when requesting or assigning IP values for your storage system. Ethernet Management Port Use DHCP to obtain a different IP address for each Ethernet management port (one each for controller A and controller B).
iSCSI host ports should be assigned IP addresses that are on one or the other subnet to which data host ports are assigned. That is, one iSCSI host port on controller A should be on the same subnet as one of the data host ports, with the other iSCSI host port on the subnet as the other data host port, and likewise for controller B. Correcting Enclosure IDs When installing a system with drive enclosures attached, the enclosure IDs might not agree with the physical cabling order.
CH A P T E R 3 Connecting Hosts This chapter describes how to connect data and management hosts to controller enclosures.
■ To prevent Microsoft Windows® data hosts from displaying the Found New Hardware Wizard when the storage system is discovered, install the MSA2000 Family SCSI Enclosure Services driver. For more information, see “Installing the MSA2000 Family SES Driver for Microsoft Windows Hosts” on page 41. Installing the Microsoft iSCSI Software Initiator Note – This section applies only to Microsoft Windows hosts that use Ethernet adapters (NIC hardware) for iSCSI connectivity.
Installing the MSA2000 Family SES Driver for Microsoft Windows Hosts Installing the MSA2000 Family SCSI Enclosure Services (SES) driver prevents Microsoft Windows hosts from displaying the Found New Hardware Wizard when the storage system is discovered. 1. Download the MSA2000 Family SCSI Enclosure Services (SES) driver package msa2000-ses-version.zip from http://www.hp.com/go/msa. Select MSA SAN arrays, select your product, and go to Related products. 2.
Figure 3-1 shows the preferred high-availability dual-controller connection through two switches to two dual-port data hosts, in which each data host has two Ethernet ports with each port connected to a different switch.
Connecting Remote Management Hosts The management host directly manages systems out-of-band over an Ethernet network. This section describes how to connect the Ethernet cables to the management host. 1. Connect an Ethernet cable to the Ethernet management port on each controller. Note – Do not confuse Ethernet management ports with Ethernet host ports, also located on the rear panel of the controller enclosure. For a description of controller enclosure ports, see “Hardware Components and LEDs” on page 13.
HP StorageWorks 2012i Modular Smart Array user guide • March 2008
CH A P T E R 4 Configuring a System for the First Time This chapter describes how to perform first-time configuration required on both the storage system and data hosts. It also describes how to perform basic storage configuration to verify that your system is working.
Setting Management Port IP Addresses Using the CLI Note – If you used DHCP to set the IP addresses, you do not have to set them using the CLI as described in this section. Ethernet Management ports on controller module A and controller module B are configured with the following default values: ■ Management Port IP Address: 10.0.0.2 (controller A), 10.0.0.3 (controller B) ■ IP Subnet Mask: 255.255.255.0 ■ Gateway IP Address: 10.0.0.
Your package contents include a micro-DB9-to-DB9 serial cable. If necessary, use a DB9-to-DB25 adapter (not included) for connecting the serial cable to a DB25 serial port on the host computer. 2. Start and configure a terminal emulator, such as HyperTerminal or VT-100, using the display settings in Table 4-1 and the connection settings in Table 4-2.
3. In the terminal emulator, connect to controller A. 4. Press Enter to display the CLI prompt (#). 5.
8. In the host computer's command window, type the following command to verify Ethernet connectivity, first for controller A and then for controller B: ping IP-address If you cannot your access your system for at least three minutes after changing the IP address, your network might require you to restart the management controller using the serial CLI. When you restart a management controller, communication with it is temporarily lost until it successfully restarts.
Logging in to SMU from a Local Management Host To log in to SMU from a local management host: 1. In your web browser’s address field, type the IP address of one of the controller enclosure’s Ethernet management ports and press Enter. The SMU Login page is displayed. If the Login page does not display, verify that you have entered the correct IP address. 2. On the login page, type the default management user name manage and default password !manage. 3. Click Log In. The Status Summary page is displayed.
NTP server time is provided in Universal Time (UT), which provides several options: ■ If you want to synchronize the times and logs between storage devices installed in multiple time zones, set all the storage devices to use UT. ■ If you want to use the local time for the device, set its time zone appropriately. ■ If a time server can provide local time rather than UT, configure the storage devices to use that time server, with no further time adjustment.
Configuring Controller Enclosure Host Ports To configure iSCSI host ports on the controller enclosure, complete the following steps: 1. Select Manage > General Config > Host Port Configuration. 2. In the Controller Module Host Port Configuration panels, for each host port on controller A and controller B, enter the following values: ■ IP address. (Refer to the list of IP addresses you obtained after you installed the enclosures.) ■ Subnet mask. Set all subnet mask fields to 255.255.255.
5. Click OK to save these settings. 6. Complete Step 3 through Step 5 for the second data host Ethernet port, selecting IP addresses on the subnet not used for the first Ethernet port. IP properties have been set for Ethernet ports on the data host. 7. Complete Step 1 to Step 6 on additional data hosts.
■ ■ ■ Data host IP addresses may not be set correctly Controller enclosure host port addresses may not be set correctly on the data host Cables between the controller enclosure and/or switches and/or data hosts may not be connected correctly Correct the issue, return to the Targets tab and click Refresh. 6. If two targets are configured, select the first target (controller module) and click Log On. 7. On the Log On to Target dialog, set the following options: a.
10. On the Persistent Targets tab, verify that two entries appear for each controller (.a and .b) for a total of four connections. Configuring more than one session per controller port will use additional host interface resources and may cause failover to function improperly. If two persistent targets are not configured for each controller host port, complete the following steps to remove and reconfigure targets: a. Select each entry and click Remove. b.
Optimizing NIC Hardware TCP Settings To improve performance on single-threaded read and write actions, edit the TCP registry settings as follows. Note – For hosts running Windows Server 2003 SP1 or later. 1. Start the Registry Editor. 2. Locate and select the following registry subkey: HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\Tcpip\ Parameters\Interfaces The interfaces will be listed below the key using automatically generated Globally Unique Identifiers (GUIDs).
Optimizing iSCSI Initiator Parameters To optimize performance, edit the following two iSCSI initiator registry keys: ■ LinkDownTime: Edit this key to increase the amount of time that the host allows for failover on the controller enclosure before removing the controller from the system. ■ MaxTransferLength: (Optional) The default registry setting for maximum size per I/O transfer is 256 KB. This results in larger transfers being segmented into multiple commands.
Creating Virtual Disks Two or more disk drives can be logically combined to form a virtual disk. The combined storage capacity can then be partitioned into volumes. SMU provides both manual and automatic methods for creating virtual disks, as described in its online help and in the Administrator’s Guide.
Mapping a Data Host to a Volume To enable a data host to access a volume you created, you must map the volume to the host. The host value, typically the IQN (iSCSI qualified name), of each host port connected to the system is automatically added to the system’s global host port list. Before mapping a data host to a volume you must identify the data host’s iSCSI node name (IQN) and a LUN that the host is not using. To map a data host to a volume: 1.
3. Once you have determined that your system is ready for use, tighten the thumb screws on all SAS cables. 4. Optionally, unmount the volume and delete the test vdisks. Logging Out of SMU If you do not log out of SMU when you have finished using it, other manage users cannot log in to the same controller module and your IP address stays logged in for 30 minutes (the default auto-logout timeout setting). To log out of SMU: 1. Click Log Off at the bottom of the menu. The Log Off page is displayed. 2.
APPENDIX A Powering the System Off and On This appendix describes how to power off and power on the system when needed. Powering Off the System The system rarely needs to be powered off. You remove power only when you plan to physically move the system to another location. Use this procedure when you need to power off the system. 1. Stop all I/O from hosts to the system. 2. Use SMU to shut down both controllers. Wait until SMU indicates that processing is complete. 3.
2. Press the power switches at the back of the controller enclosure to the On (–) position. If the enclosure’s power-on sequence succeeds as described in Step 1, the system is ready to use.
APPENDIX B Regulatory Compliance and Safety Regulatory Compliance Federal Communications Commission Notice Part 15 of the Federal Communications Commission (FCC) Rules and Regulations has established Radio Frequency (RF) emission limits to provide an interferencefree radio frequency spectrum. Many electronic devices, including computers, generate RF energy incidental to their intended function and are, therefore, covered by these rules.
instructions, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at personal expense. Class B Equipment This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
To identify this product, refer to the part, Regulatory Model Number, or product number found on the product. Modifications The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by Hewlett-Packard Company may void the user's authority to operate the equipment. Cables Connections to this device must be made with shielded cables with metallic RFI/EMI connector hoods in order to maintain compliance with FCC Rules and Regulations.
Laser Safety Warning Warning – To reduce the risk of exposure to hazardous radiation: ■ ■ ■ Do not try to open the laser device enclosure. There are no user-serviceable components inside. Do not operate controls, make adjustments, or perform procedures to the laser device other than those specified herein. Allow only HP authorized service technicians to repair the laser device.
International Notices and Statements Canadian Notice (avis Canadien) Class A Equipment This Class A digital apparatus meets all requirements of the Canadian InterferenceCausing Equipment Regulations. Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. Class B Equipment This Class B digital apparatus meets all requirements of the Canadian InterferenceCausing Equipment Regulations.
■ Also approved under UL 60950/CSA C22.2 No. 60950-00, Safety of Information Technology Equipment.
Korean Notices Safety Battery Replacement Notice Your computer is equipped with a lithium manganese dioxide, a vanadium pentoxide, or an alkaline internal battery or battery pack. There is a danger of explosion and risk of personal injury if the battery is incorrectly replaced or mistreated. Replacement is to be done by an HP authorized service provider using the HP spare part designated for this product.
Batteries, battery packs, and accumulators should not be disposed of together with the general household waste. To forward them to recycling or proper disposal, please use the public collection system or return them to HP, an authorized HP Partner, or their agents. For more information about battery replacement or proper disposal, contact an HP authorized reseller or service provider.
Japanese Power Cord Notice Electrostatic Discharge To prevent damage to the system, be aware of the precautions you need to follow when setting up the system or handling parts. A discharge of static electricity from a finger or other conductor may damage system boards or other static-sensitive devices. This type of damage may reduce the life expectancy of the device.
Note – For more information on static electricity, or assistance with product installation, contact your HP authorized reseller. Waste Electrical and Electronic Equipment Directive Czechoslovakian Notice Danish Notice Bortskaffelse af affald fra husstande i den Europæiske Union Hvis produktet eller dets emballage er forsynet med dette symbol, angiver det, at produktet ikke må bortskaffes med andet almindeligt husholdningsaffald.
Dutch Notice Verwijdering van afgedankte apparatuur door privé-gebruikers in de Europese Unie Dit symbool op het product of de verpakking geeft aan dat dit product niet mag worden gedeponeerd bij het normale huishoudelijke afval. U bent zelf verantwoordelijk voor het inleveren van uw afgedankte apparatuur bij een inzamelingspunt voor het recyclen van oude elektrische en elektronische apparatuur.
Estonian Notice Seadmete jäätmete kõrvaldamine eramajapidamistes Euroopa Liidus See tootel või selle pakendil olev sümbol näitab, et kõnealust toodet ei tohi koos teiste majapidamisjäätmetega kõrvaldada. Teie kohus on oma seadmete jäätmed kõrvaldada, viies need elektri- ja elektroonikaseadmete jäätmete ringlussevõtmiseks selleks ettenähtud kogumispunkti.
French Notice Élimination des appareils mis au rebut par les ménages dans l'Union européenne Le symbole apposé sur ce produit ou sur son emballage indique que ce produit ne doit pas être jeté avec les déchets ménagers ordinaires. Il est de votre responsabilité de mettre au rebut vos appareils en les déposant dans les centres de collecte publique désignés pour le recyclage des équipements électriques et électroniques.
Greek Notice . , . . , , . Hungarian Notice Készülékek magánháztartásban történ selejtezése az Európai Unió területén A készüléken, illetve a készülék csomagolásán látható azonos szimbólum annak jelzésére szolgál, hogy a készülék a selejtezés során az egyéb háztartási hulladéktól eltér módon kezelend . A vásárló a hulladékká vált készüléket köteles a kijelölt gy jt helyre szállítani az elektromos és elektronikai készülékek újrahasznosítása céljából.
Italian Notice Smaltimento delle apparecchiature da parte di privati nel territorio dell'Unione Europea Questo simbolo presente sul prodotto o sulla sua confezione indica che il prodotto non può essere smaltito insieme ai rifiuti domestici. È responsabilità dell'utente smaltire le apparecchiature consegnandole presso un punto di raccolta designato al riciclo e allo smaltimento di apparecchiature elettriche ed elettroniche.
Lihuanian Notice Nolietotu iek rtu izn cin šanas noteikumi lietot jiem Eiropas Savien bas priv taj s m jsaimniec b s Š ds simbols uz izstr d juma vai uz t iesai ojuma nor da, ka šo izstr d jumu nedr kst izmest kop ar citiem sadz ves atkritumiem. J s atbildat par to, lai nolietot s iek rtas tiktu nodotas speci li iek rtotos punktos, kas paredz ti izmantoto elektrisko un elektronisko iek rtu sav kšanai otrreiz jai p rstr dei.
Portuguese Notice Descarte de Lixo Elétrico na Comunidade Européia Este símbolo encontrado no produto ou na embalagem indica que o produto não deve ser descartado no lixo doméstico comum. É responsabilidade do cliente descartar o material usado (lixo elétrico), encaminhando-o para um ponto de coleta para reciclagem.
Slovenian Notice Spanish Notice Eliminación de residuos de equipos eléctricos y electrónicos por parte de usuarios particulares en la Unión Europea Este símbolo en el producto o en su envase indica que no debe eliminarse junto con los desperdicios generales de la casa. Es responsabilidad del usuario eliminar los residuos de este tipo depositándolos en un "punto limpio" para el reciclado de residuos eléctricos y electrónicos.
Swedish Notice Bortskaffande av avfallsprodukter från användare i privathushåll inom Europeiska Unionen Om den här symbolen visas på produkten eller förpackningen betyder det att produkten inte får slängas på samma ställe som hushållssopor. I stället är det ditt ansvar att bortskaffa avfallet genom att överlämna det till ett uppsamlingsställe avsett för återvinning av avfall från elektriska och elektroniska produkter.
HP StorageWorks 2012i Modular Smart Array user guide • March 2008
Index A accessing SMU, 50 the CLI, 46 accumulators, 70 Avis Canadien, regulatory compliance notice, 67 B batteries recycling or disposal, 70 replacement notice, 69 Taiwan EPA recycling and disposal, 70 boot straps, using, 71 BSMI, regulatory compliance notice, 68 C cables FCC compliance statement, 65 shielded, 65 Canada, regulatory compliance notice, 67 certification and classification information, laser, 66 Class A equipment, Canadian compliance statement, 67 Class B equipment, Canadian compliance statem
disposal waste equipment for EU private households, 73 disposal, battery, 70 disposal, Taiwan EPA battery, 70 dissipating floor mats, 71 drive enclosures components, 19 connecting to controller enclosures, 32 connecting to other drive enclosures, 32 drive modules LEDs, 15 location, 14 E Class A Equipment, compliance notice, 63 Class B Equipment, compliance notice, 64 declaration of conformity, 64 modifications, 65 notice, 63 Federal Communications Commission.
K Korean, regulatory compliance notice, 69 L label, laser, 66 laser international certification and classification information, 66 product label, 66 radiation, warning, 66 regulatory compliance notice, 65 LEDs AC Power Good, 17, 21 cache status, 18 DC Voltage/Fan Fault/Service Required, 17, 21 drive modules, 15 Enclosure ID, 14 Ethernet activity, 18 Ethernet link status, 18 expansion port status, 18 fault ID, 14 Fault/Service Required, 18, 22 FRU OK, 22 heartbeat, 14 host activity, 18 host link speed, 17 h
S V safety precautions, 26 series number, regulatory compliance, 65 SES driver, installing on data hosts, 41 SMU additional documentation, 60 configuring, 49 creating virtual disks, 58 logging in, 50 logging out, 60 testing system configuration, 59 static-dissipating work mat, 71 static-safe containers storing products, 71 transporting products, 71 status LEDs, 14 Storage Management Utility, See SMU storage system configuring for the first time, 45 powering off, 61 powering on, 61 testing configuration, 5
