user manual

System Board Connectors and Jumpers (position of some untitled components may vary in location)
CR1 5V_Aux LED P11 Aux audio in
E49 Password jumper P14 Boot Block
J20 PCI slot 1 P20 Primary IDE
J21 PCI slot 2 P23 Front audio/USB
J30 PCI slot extender P27 MiultiBay
J31 PCI Express x1 P29 SCSI LED
J41 PCI Express x16 P70 CPU fan
P1 Main power (20 pin) P124 Hood lock
P3 CPU regulator power (4 pin) SW50 CMOS button
P5 Front panel XBT2 Battery
P6 Internal chassis speaker XMM1 Memory socket
P7 CD audio in XMM2 Memory socket
P8 Chassis fan XMM3 Memory socket
P10 Diskette drive XMM4 Memory socket
XU1 Processor socket
System Hardware Interrupts
IRQ System Function IRQ System Function
0 Timer Interrupt 8 Real-Time Clock
1 Keyboard 9 Unused
2 Interrupt Controller Cascade 10 Unused, available for PCI
3 Serial Port (COM B) 11 Unused, available for PCI
4 Serial Port (COM A) 12 Mouse
5 Unused, available for PCI 13 Coprocessor
6 Diskette Drive 14 Primary ATA (IDE) Controller
7 Parallel Port (LPT 1)
Computer Diagnostic LEDs (on front of computer)
LED Color LED/Beep Activity State/Message
Power Green On (S0) Computer on
Power Green 1 blink every 2 seconds (S1) Suspend Mode
Power Green 1 blink every 2 seconds (S3) Suspend to RAM
Power Clear Off (S4) Hibernation
Power Clear Off (S5) Computer off
Power Red* 2 blinks and beeps 1 second
apart
CPU thermal shutdown
Power Red* 3 blinks and beeps 1 second
apart
CPU not installed
Power Red* 4 blinks and beeps 1 second
apart
Power supply overload (crow bar)
Power Red* 5 blinks and beeps 1 second
apart
Bad memory
Power Red* 6 blinks and beeps 1 second
apart
Graphics adapter error
Power Red* 7 blinks 1 and beeps second
apart
System board failure (detected prior to video)
Power Red* 8 blinks and beeps 1 second
apart
Invalid ROM checksum
Power Red* 9 blinks and beeps 1 second
apart
System not fetching code
Power Red* 10 blinks and beeps1 second
apart
System hang while loading an option ROM
Hard Drive Green Blinking Hard drive activity
*Blinking codes are repeated after a 2 second pause. Beeps stop after fifth iteration but LEDs continue until problem is
resolved.
Keyboard Diagnostic LEDs, PS/2 Keyboards Only
LED Color LED Activity State/Message
Num, Caps,
Scroll Lock
Green On (Rising Tone) ROM reflashed successfully
Num Lock Green On ROMPaq diskette not present, is bad, or drive
not ready.*
Caps Lock Green On Enter password.
Num, Caps,
Scroll Lock
Green Blink On in sequence, one at a
time - N, C, SL
Keyboard locked in network mode
* Insert valid ROMPaq diskette in drive A. Turn power switch off, then on to reflash ROM. If ROM flash is successful, all
three keyboard LEDs will light up, and you will hear a rising tone series of beeps. Remove diskette and turn power off,
then on to restart the computer. For more information about flashing the ROM, refer to the Troubleshooting guide.
Clearing CMOS
The computer's configuration (CMOS) may occasionally be corrupted. If it is, it is necessary to clear the CMOS
memory using switch SW50.
To clear and reset the configuration, perform the following procedure:
1. Prepare the computer for disassembly.
Ä
CAUTION: The power cord must be disconnected from the power source before pushing the Clear CMOS
Button (NOTE: All LEDs on the board should be OFF). Failure to do so may damage the system board
2. Remove the access panel.
3. Press the CMOS button located on the system board and keep it depressed for 5 seconds.
4. Replace the access panel.
5. Turn the computer on and run F10 Computer Setup (Setup-utility) to reconfigure the system.
Disabling or Clearing the Power-On and Setup Passwords
1. Turn off the computer and any external devices, and disconnect the power cord from the power outlet.
2. Remove the access panel.
3. Locate the header and jumper labeled E49.
4. Remove the jumper from pins 1 and 2. Place the jumper over pin 2 only, in order to avoid losing it.
5. Replace the access panel.
6. Plug in the computer and turn on power. Allow the operating system to start.
NOTE: Placing the jumper on pin 2 clears the current passwords and disables the password features.
7. To re-enable the password features, repeat steps 1-3, then replace the jumper on pins 1 and 2.
8. Repeat steps 5-6, then establish new passwords.
Refer to the Computer Setup (F10 Setup) instructions to establish new passwords.
Computer Setup (F10) Utility Features (not all features may be available)
File
System Information
About
Set Time and date
Replicated Setup
Default Setup
Apply Defaults and Exit
Ignore Changes and Exit
Save Changes and Exit
Storage
Device Configuration
Storage Options
DPS Self-Test
Boot Order
Security
Setup Password
Power-On Password
Password Options
Smart Cover
Embedded Security
Drivelock Security
Data Execution Prevention
Master Boot Record Security
Save Master Boot Record
Restore Master Boot Record
Device Security
Network Service Boot
System IDs
Power
OS Power Management Hardware Power Management Thermal
Advanced
Power-On Options
BIOS Power On
Onboard devices
PCI Devices
Bus Options
Device Options
PCI VGA Configuration