user manual
Table Of Contents
- Product Features
- Installing and Customizing the Software
- Computer Setup (F10) Utility
- Computer Diagnostic Features
- Desktop Management
- Initial Configuration and Deployment
- Remote System Installation
- Software Updating and Management
- HP Client Management Interface
- HP SoftPaq Download Manager
- HP System Software Manager
- HP ProtectTools Security Manager
- HP Client Automation Starter and Standard Editions
- HP Client Automation Enterprise Edition
- HP Client Manager from Symantec
- Altiris Client Management Suite
- HP Client Catalog for Microsoft System Center & SMS Products
- Remote Management Technology
- Configuring the Intel Management Engine
- Verdiem Surveyor
- HP Proactive Change Notification
- Subscriber’s Choice
- Retired Solutions
- ROM Flash
- Boot Block Emergency Recovery Mode
- Replicating the Setup
- Dual-State Power Button
- HP Web Site Support
- Industry Standards
- Asset Tracking and Security
- Serial ATA Drive Guidelines and Features
- Identifying the Chassis, Routine Care, and Disassembly Preparation
- Removal and Replacement Procedures Microtower (MT) Chassis
- Serial Number Location
- Preparation for Disassembly
- Access Panel
- Front Bezel
- Removing Bezel Blanks
- Cable Management
- Cable Connections
- Memory
- Expansion Cards
- Installing and Removing Drives
- Fan/Baffle Assembly
- Front I/O Assembly
- Power Switch/LED Assembly
- Heat sink
- Processor
- Speaker
- Rear Chassis Fan
- Power Supply
- System Board
- Battery
- External Security Devices
- Removal and Replacement Procedures Small Form Factor (SFF) Chassis
- Preparation for Disassembly
- Access Panel
- Front Bezel
- Bezel Blanks
- Installing Additional Memory
- Expansion Cards
- Cable Management
- Cable Connections
- Drive Positions
- Installing and Removing Drives
- System Board Drive Connections
- Removing an External 5.25-inch Drive
- Installing an Optical Drive into the 5.25-inch Drive Bay
- Removing an External 3.5-inch Drive
- Installing a Drive into the 3.5-inch External Drive Bay
- Removing and Replacing the Primary 3.5-inch Internal SATA Hard Drive
- Removing and Replacing a Removable 3.5-inch SATA Hard Drive
- Baffle
- Front Fan Assembly
- Front I/O and Power Switch Assembly
- Speaker
- Heat sink
- Processor
- Power Supply
- System Board
- Battery
- External Security Devices
- Using the Small Form Factor Computer in a Tower Orientation
- Connector Pin Assignments
- Power Cord Set Requirements
- POST Error Messages
- Troubleshooting Without Diagnostics
- Safety and Comfort
- Before You Call for Technical Support
- Helpful Hints
- Solving General Problems
- Solving Power Problems
- Solving Hard Drive Problems
- Solving Media Card Reader Problems
- Solving Display Problems
- Solving Audio Problems
- Solving Printer Problems
- Solving Keyboard and Mouse Problems
- Solving Hardware Installation Problems
- Solving Network Problems
- Solving Memory Problems
- Solving Processor Problems
- Solving CD-ROM and DVD Problems
- Solving USB Flash Drive Problems
- Solving Front Panel Component Problems
- Solving Internet Access Problems
- Solving Software Problems
- Contacting Customer Support
- Password Security and Resetting CMOS
- Specifications
- Index
Using the Small Form Factor Computer in a Tower
Orientation
The Small Form Factor computer can be used in a tower orientation with an optional tower stand that
can be purchased from HP.
1. Remove/disengage any security devices that prohibit opening the computer.
2. Remove all removable media, such as compact discs or USB flash drives, from the computer.
3. Turn off the computer properly through the operating system, then turn off any external devices.
4. Disconnect the power cord from the power outlet and disconnect any external devices.
CAUTION: Regardless of the power-on state, voltage is always present on the system board as
long as the system is plugged into an active AC outlet. You must disconnect the power cord to
avoid damage to the internal components of the computer.
5. Orient the computer so that its right side is facing down and place the computer in the optional
stand.
Figure 9-66 Changing from Desktop to Tower Orientation
NOTE: To stabilize the computer in a tower orientation, HP recommends the use of the optional
tower stand.
6. Reconnect the power cord and any external devices, then turn on the computer.
NOTE: Ensure at least 10.2 centimeters (4 inches) of space on all sides of the computer remains clear
and free of obstructions.
174 Chapter 9 Removal and Replacement Procedures Small Form Factor (SFF) Chassis