user manual
Table Of Contents
- Product Features
- Installing and Customizing the Software
- Computer Setup (F10) Utility
- Computer Diagnostic Features
- Desktop Management
- Initial Configuration and Deployment
- Remote System Installation
- Software Updating and Management
- HP Client Management Interface
- HP SoftPaq Download Manager
- HP System Software Manager
- HP ProtectTools Security Manager
- HP Client Automation Starter and Standard Editions
- HP Client Automation Enterprise Edition
- HP Client Manager from Symantec
- Altiris Client Management Suite
- HP Client Catalog for Microsoft System Center & SMS Products
- Remote Management Technology
- Configuring the Intel Management Engine
- Verdiem Surveyor
- HP Proactive Change Notification
- Subscriber’s Choice
- Retired Solutions
- ROM Flash
- Boot Block Emergency Recovery Mode
- Replicating the Setup
- Dual-State Power Button
- HP Web Site Support
- Industry Standards
- Asset Tracking and Security
- Serial ATA Drive Guidelines and Features
- Identifying the Chassis, Routine Care, and Disassembly Preparation
- Removal and Replacement Procedures Microtower (MT) Chassis
- Serial Number Location
- Preparation for Disassembly
- Access Panel
- Front Bezel
- Removing Bezel Blanks
- Cable Management
- Cable Connections
- Memory
- Expansion Cards
- Installing and Removing Drives
- Fan/Baffle Assembly
- Front I/O Assembly
- Power Switch/LED Assembly
- Heat sink
- Processor
- Speaker
- Rear Chassis Fan
- Power Supply
- System Board
- Battery
- External Security Devices
- Removal and Replacement Procedures Small Form Factor (SFF) Chassis
- Preparation for Disassembly
- Access Panel
- Front Bezel
- Bezel Blanks
- Installing Additional Memory
- Expansion Cards
- Cable Management
- Cable Connections
- Drive Positions
- Installing and Removing Drives
- System Board Drive Connections
- Removing an External 5.25-inch Drive
- Installing an Optical Drive into the 5.25-inch Drive Bay
- Removing an External 3.5-inch Drive
- Installing a Drive into the 3.5-inch External Drive Bay
- Removing and Replacing the Primary 3.5-inch Internal SATA Hard Drive
- Removing and Replacing a Removable 3.5-inch SATA Hard Drive
- Baffle
- Front Fan Assembly
- Front I/O and Power Switch Assembly
- Speaker
- Heat sink
- Processor
- Power Supply
- System Board
- Battery
- External Security Devices
- Using the Small Form Factor Computer in a Tower Orientation
- Connector Pin Assignments
- Power Cord Set Requirements
- POST Error Messages
- Troubleshooting Without Diagnostics
- Safety and Comfort
- Before You Call for Technical Support
- Helpful Hints
- Solving General Problems
- Solving Power Problems
- Solving Hard Drive Problems
- Solving Media Card Reader Problems
- Solving Display Problems
- Solving Audio Problems
- Solving Printer Problems
- Solving Keyboard and Mouse Problems
- Solving Hardware Installation Problems
- Solving Network Problems
- Solving Memory Problems
- Solving Processor Problems
- Solving CD-ROM and DVD Problems
- Solving USB Flash Drive Problems
- Solving Front Panel Component Problems
- Solving Internet Access Problems
- Solving Software Problems
- Contacting Customer Support
- Password Security and Resetting CMOS
- Specifications
- Index
Solving Front Panel Component Problems
If you encounter problems with devices connected to the front panel, refer to the common causes and
solutions listed in the following table.
Table D-16 Solving Front Panel Component Problems
A USB device, headphone, or microphone is not recognized by the computer.
Cause
Solution
Device is not properly connected. 1. Turn off the computer.
2. Reconnect the device to the front of the computer and
restart the computer.
The device does not have power. If the USB device requires AC power, be sure one end is
connected to the device and one end is connected to a live
outlet.
The correct device driver is not installed. 1. Install the correct driver for the device.
2. You might need to reboot the computer.
The cable from the device to the computer does not work. 1. If possible, replace the cable.
2. Restart the computer.
The device is not working. 1. Replace the device.
2. Restart the computer.
USB ports on the computer are disabled in Computer Setup. Enter Computer Setup (F10) and enable the USB ports.
Solving Internet Access Problems
If you encounter Internet access problems, consult your Internet Service Provider (ISP) or refer to the
common causes and solutions listed in the following table.
Table D-17 Solving Internet Access Problems
Unable to connect to the Internet.
Cause
Solution
Internet Service Provider (ISP) account is not set up properly. Verify Internet settings or contact your ISP for assistance.
Modem is not set up properly. Reconnect the modem. Verify the connections are correct
using the quick setup documentation.
Web browser is not set up properly. Verify that the Web browser is installed and set up to work with
your ISP.
Cable/DSL modem is not plugged in. Plug in cable/DSL modem. You should see a “power” LED light
on the front of the cable/DSL modem.
Cable/DSL service is not available or has been interrupted due
to bad weather.
Try connecting to the Internet at a later time or contact your
ISP. (If the cable/DSL service is connected, the “cable” LED
light on the front of the cable/DSL modem will be on.)
The CAT5 UTP cable is disconnected. Connect the CAT5 UTP cable between the cable modem and
the computers’s RJ-45 connector. (If the connection is good,
the “PC” LED light on the front of the cable/DSL modem will be
on.)
228 Appendix D Troubleshooting Without Diagnostics