user manual
Table Of Contents
- Product Features
- Installing and Customizing the Software
- Computer Setup (F10) Utility
- Computer Diagnostic Features
- Desktop Management
- Initial Configuration and Deployment
- Remote System Installation
- Software Updating and Management
- HP Client Management Interface
- HP SoftPaq Download Manager
- HP System Software Manager
- HP ProtectTools Security Manager
- HP Client Automation Starter and Standard Editions
- HP Client Automation Enterprise Edition
- HP Client Manager from Symantec
- Altiris Client Management Suite
- HP Client Catalog for Microsoft System Center & SMS Products
- Remote Management Technology
- Configuring the Intel Management Engine
- Verdiem Surveyor
- HP Proactive Change Notification
- Subscriber’s Choice
- Retired Solutions
- ROM Flash
- Boot Block Emergency Recovery Mode
- Replicating the Setup
- Dual-State Power Button
- HP Web Site Support
- Industry Standards
- Asset Tracking and Security
- Serial ATA Drive Guidelines and Features
- Identifying the Chassis, Routine Care, and Disassembly Preparation
- Removal and Replacement Procedures Microtower (MT) Chassis
- Serial Number Location
- Preparation for Disassembly
- Access Panel
- Front Bezel
- Removing Bezel Blanks
- Cable Management
- Cable Connections
- Memory
- Expansion Cards
- Installing and Removing Drives
- Fan/Baffle Assembly
- Front I/O Assembly
- Power Switch/LED Assembly
- Heat sink
- Processor
- Speaker
- Rear Chassis Fan
- Power Supply
- System Board
- Battery
- External Security Devices
- Removal and Replacement Procedures Small Form Factor (SFF) Chassis
- Preparation for Disassembly
- Access Panel
- Front Bezel
- Bezel Blanks
- Installing Additional Memory
- Expansion Cards
- Cable Management
- Cable Connections
- Drive Positions
- Installing and Removing Drives
- System Board Drive Connections
- Removing an External 5.25-inch Drive
- Installing an Optical Drive into the 5.25-inch Drive Bay
- Removing an External 3.5-inch Drive
- Installing a Drive into the 3.5-inch External Drive Bay
- Removing and Replacing the Primary 3.5-inch Internal SATA Hard Drive
- Removing and Replacing a Removable 3.5-inch SATA Hard Drive
- Baffle
- Front Fan Assembly
- Front I/O and Power Switch Assembly
- Speaker
- Heat sink
- Processor
- Power Supply
- System Board
- Battery
- External Security Devices
- Using the Small Form Factor Computer in a Tower Orientation
- Connector Pin Assignments
- Power Cord Set Requirements
- POST Error Messages
- Troubleshooting Without Diagnostics
- Safety and Comfort
- Before You Call for Technical Support
- Helpful Hints
- Solving General Problems
- Solving Power Problems
- Solving Hard Drive Problems
- Solving Media Card Reader Problems
- Solving Display Problems
- Solving Audio Problems
- Solving Printer Problems
- Solving Keyboard and Mouse Problems
- Solving Hardware Installation Problems
- Solving Network Problems
- Solving Memory Problems
- Solving Processor Problems
- Solving CD-ROM and DVD Problems
- Solving USB Flash Drive Problems
- Solving Front Panel Component Problems
- Solving Internet Access Problems
- Solving Software Problems
- Contacting Customer Support
- Password Security and Resetting CMOS
- Specifications
- Index

F Specifications
This chapter provides specifications for the microtower and small form factor chassis.
Microtower Chassis
Table F-1 Specifications
Desktop Dimensions
Height
Width
Depth
14.85 in
6.95 in
16.85 in
37.72 cm
17.65 cm
42.80 cm
Approximate Weight 23.5 lb 10.66 kg
Temperature Range
Operating
Nonoperating
50° to 95°F
-22° to 140°F
10° to 35°C
-30° to 60°C
Relative Humidity (noncondensing)
Operating
Nonoperating (38.7°C max wet bulb)
10-90%
5-95%
10-90%
5-95%
Maximum Altitude (unpressurized)
Operating
Nonoperating
10,000 ft
30,000 ft
3048 m
9144 m
NOTE: Operating temperature is derated 1.0° C per 300 m (1000 ft) to 3000 m (10,000 ft) above sea level; no direct sustained
sunlight. Maximum rate of change is 10° C/Hr. The upper limit may be limited by the type and number of options installed.
Heat Dissipation
Max STD PS
Typical STD PS idle
Max EPA 87/89/85% @ 20/50/100% load PS
Typical EPA 87/89/85% @ 20/50/100% load PS idle
1410 BTU/hr
TBD BTU/hr
1255 BTU/hr
TBD BTU/hr
356 kg-cal/hr
TBD kg-cal/hr
316 kg-cal/hr
TBD kg-cal/hr
Microtower Chassis 237