user manual
Table Of Contents
- Product Features
- Installing and Customizing the Software
- Computer Setup (F10) Utility
- Computer Diagnostic Features
- Desktop Management
- Initial Configuration and Deployment
- Remote System Installation
- Software Updating and Management
- HP Client Management Interface
- HP SoftPaq Download Manager
- HP System Software Manager
- HP ProtectTools Security Manager
- HP Client Automation Starter and Standard Editions
- HP Client Automation Enterprise Edition
- HP Client Manager from Symantec
- Altiris Client Management Suite
- HP Client Catalog for Microsoft System Center & SMS Products
- Remote Management Technology
- Configuring the Intel Management Engine
- Verdiem Surveyor
- HP Proactive Change Notification
- Subscriber’s Choice
- Retired Solutions
- ROM Flash
- Boot Block Emergency Recovery Mode
- Replicating the Setup
- Dual-State Power Button
- HP Web Site Support
- Industry Standards
- Asset Tracking and Security
- Serial ATA Drive Guidelines and Features
- Identifying the Chassis, Routine Care, and Disassembly Preparation
- Removal and Replacement Procedures Microtower (MT) Chassis
- Serial Number Location
- Preparation for Disassembly
- Access Panel
- Front Bezel
- Removing Bezel Blanks
- Cable Management
- Cable Connections
- Memory
- Expansion Cards
- Installing and Removing Drives
- Fan/Baffle Assembly
- Front I/O Assembly
- Power Switch/LED Assembly
- Heat sink
- Processor
- Speaker
- Rear Chassis Fan
- Power Supply
- System Board
- Battery
- External Security Devices
- Removal and Replacement Procedures Small Form Factor (SFF) Chassis
- Preparation for Disassembly
- Access Panel
- Front Bezel
- Bezel Blanks
- Installing Additional Memory
- Expansion Cards
- Cable Management
- Cable Connections
- Drive Positions
- Installing and Removing Drives
- System Board Drive Connections
- Removing an External 5.25-inch Drive
- Installing an Optical Drive into the 5.25-inch Drive Bay
- Removing an External 3.5-inch Drive
- Installing a Drive into the 3.5-inch External Drive Bay
- Removing and Replacing the Primary 3.5-inch Internal SATA Hard Drive
- Removing and Replacing a Removable 3.5-inch SATA Hard Drive
- Baffle
- Front Fan Assembly
- Front I/O and Power Switch Assembly
- Speaker
- Heat sink
- Processor
- Power Supply
- System Board
- Battery
- External Security Devices
- Using the Small Form Factor Computer in a Tower Orientation
- Connector Pin Assignments
- Power Cord Set Requirements
- POST Error Messages
- Troubleshooting Without Diagnostics
- Safety and Comfort
- Before You Call for Technical Support
- Helpful Hints
- Solving General Problems
- Solving Power Problems
- Solving Hard Drive Problems
- Solving Media Card Reader Problems
- Solving Display Problems
- Solving Audio Problems
- Solving Printer Problems
- Solving Keyboard and Mouse Problems
- Solving Hardware Installation Problems
- Solving Network Problems
- Solving Memory Problems
- Solving Processor Problems
- Solving CD-ROM and DVD Problems
- Solving USB Flash Drive Problems
- Solving Front Panel Component Problems
- Solving Internet Access Problems
- Solving Software Problems
- Contacting Customer Support
- Password Security and Resetting CMOS
- Specifications
- Index
Computer Setup—Storage
NOTE: Support for specific Computer Setup options may vary depending on the hardware
configuration.
Table 3-3 Computer Setup—Storage
Option Description
Device Configuration Lists all installed BIOS-controlled storage devices.
When a device is selected, detailed information and options are displayed. The following options
may be presented:
Drive Emulation
Allows you to select a drive emulation type for a certain storage device. (For example, a Zip drive
can be made bootable by selecting diskette emulation.)
Emulation Type
ATAPI Zip drive:
●
None (treated as Other).
●
Diskette (treated as diskette drive).
CD-ROM: No emulation options available.
ATAPI LS-120:
●
None (treated as Other).
●
Diskette (treated as diskette drive).
Hard Disk:
●
None (prevents BIOS data accesses and disables it as a boot device).
●
Hard Disk (treated as hard disk).
Translation Mode (ATA disks only)
Lets you select the translation mode to be used for the device. This enables the BIOS to access
disks partitioned and formatted on other systems and may be necessary for users of older versions
of UNIX (e.g., SCO UNIX version 3.2). Options are Automatic, Bit-Shift, LBA Assisted, User, and
Off.
CAUTION: Ordinarily, the translation mode selected automatically by the BIOS should not be
changed. If the selected translation mode is not compatible with the translation mode that was active
when the disk was partitioned and formatted, the data on the disk will be inaccessible.
Translation Parameters (ATA disks only)
NOTE: This feature appears only when User translation mode is selected.
Allows you to specify the parameters (logical cylinders, heads, and sectors per track) used by the
BIOS to translate disk I/O requests (from the operating system or an application) into terms the hard
drive can accept. Logical cylinders may not exceed 1024. The number of heads may not exceed
256. The number of sectors per track may not exceed 63. These fields are only visible and
changeable when the drive translation mode is set to User.
SATA Default Values
Allows you to specify the default values for the Translation Mode for ATA devices.
Computer Setup (F10) Utilities 17