user manual
Table Of Contents
- Product Features
- Installing and Customizing the Software
- Computer Setup (F10) Utility
- Computer Diagnostic Features
- Desktop Management
- Initial Configuration and Deployment
- Remote System Installation
- Software Updating and Management
- HP Client Management Interface
- HP SoftPaq Download Manager
- HP System Software Manager
- HP ProtectTools Security Manager
- HP Client Automation Starter and Standard Editions
- HP Client Automation Enterprise Edition
- HP Client Manager from Symantec
- Altiris Client Management Suite
- HP Client Catalog for Microsoft System Center & SMS Products
- Remote Management Technology
- Configuring the Intel Management Engine
- Verdiem Surveyor
- HP Proactive Change Notification
- Subscriber’s Choice
- Retired Solutions
- ROM Flash
- Boot Block Emergency Recovery Mode
- Replicating the Setup
- Dual-State Power Button
- HP Web Site Support
- Industry Standards
- Asset Tracking and Security
- Serial ATA Drive Guidelines and Features
- Identifying the Chassis, Routine Care, and Disassembly Preparation
- Removal and Replacement Procedures Microtower (MT) Chassis
- Serial Number Location
- Preparation for Disassembly
- Access Panel
- Front Bezel
- Removing Bezel Blanks
- Cable Management
- Cable Connections
- Memory
- Expansion Cards
- Installing and Removing Drives
- Fan/Baffle Assembly
- Front I/O Assembly
- Power Switch/LED Assembly
- Heat sink
- Processor
- Speaker
- Rear Chassis Fan
- Power Supply
- System Board
- Battery
- External Security Devices
- Removal and Replacement Procedures Small Form Factor (SFF) Chassis
- Preparation for Disassembly
- Access Panel
- Front Bezel
- Bezel Blanks
- Installing Additional Memory
- Expansion Cards
- Cable Management
- Cable Connections
- Drive Positions
- Installing and Removing Drives
- System Board Drive Connections
- Removing an External 5.25-inch Drive
- Installing an Optical Drive into the 5.25-inch Drive Bay
- Removing an External 3.5-inch Drive
- Installing a Drive into the 3.5-inch External Drive Bay
- Removing and Replacing the Primary 3.5-inch Internal SATA Hard Drive
- Removing and Replacing a Removable 3.5-inch SATA Hard Drive
- Baffle
- Front Fan Assembly
- Front I/O and Power Switch Assembly
- Speaker
- Heat sink
- Processor
- Power Supply
- System Board
- Battery
- External Security Devices
- Using the Small Form Factor Computer in a Tower Orientation
- Connector Pin Assignments
- Power Cord Set Requirements
- POST Error Messages
- Troubleshooting Without Diagnostics
- Safety and Comfort
- Before You Call for Technical Support
- Helpful Hints
- Solving General Problems
- Solving Power Problems
- Solving Hard Drive Problems
- Solving Media Card Reader Problems
- Solving Display Problems
- Solving Audio Problems
- Solving Printer Problems
- Solving Keyboard and Mouse Problems
- Solving Hardware Installation Problems
- Solving Network Problems
- Solving Memory Problems
- Solving Processor Problems
- Solving CD-ROM and DVD Problems
- Solving USB Flash Drive Problems
- Solving Front Panel Component Problems
- Solving Internet Access Problems
- Solving Software Problems
- Contacting Customer Support
- Password Security and Resetting CMOS
- Specifications
- Index
Option Description
System Security (some
models: these options
are hardware
dependent)
Data Execution Prevention (some models) (enable/disable) - Helps prevent operating system
security breaches.
PAVP (Some models) (disabled/min) - PAVP enables the Protected Audio Video Path in the Chipset.
This may allow viewing of some protected high definition content that would otherwise be prohibited
from playback.
Virtualization Technology (some models) (enable/disable) - Controls the virtualization features of the
processor. Changing this setting requires turning the computer off and then back on.
Virtualization Technology Directed I/O (some models) (enable/disable) - Controls virtualization DMA
remapping features of the chipset. Changing this setting requires turning the computer off and then
back on.
Trusted Execution Technology (some models) (enable/disable) - Controls the underlying processor
and chipset features needed to support a virtual appliance. Changing this setting requires turning
the computer off and then back on. To enable this feature you must enable the following features:
●
Embedded Security Device Support
●
Virtualization Technology
●
Virtualization Technology Directed I/O
Embedded Security Device Support (some models) (enable/disable) - Permits activation and
deactivation of the Embedded Security Device. Changing this setting requires turning the computer
off and then back on.
NOTE: To configure the Embedded Security Device, a Setup password must be set.
●
Reset to Factory Settings (some models) (Do not reset/Reset) - Resetting to factory defaults
will erase all security keys. Changing this setting requires turning the computer off and then
back on.
CAUTION: The embedded security device is a critical component of many security schemes.
Erasing the security keys will prevent access to data protected by the Embedded Security
Device. Choosing Reset to Factory Settings may result in significant data loss.
●
Power-on authentication support (some models) (enable/disable) - Controls the power-on
password authentication scheme that utilizes the Embedded Security Device. Changing this
setting requires turning the computer off and then back on.
●
Reset authentication credentials (some models) (Do not reset/Reset) - Selecting Reset disables
the power-on authentication support and clears the authentication information from the
Embedded Security Device. Changing this setting requires turning the computer off and then
back on.
OS management of Embedded Security Device (some models) (enable/disable) - This option allows
the user to limit operating system control of the Embedded Security Device. Changing this setting
requires turning the computer off and then back on. This option allows the user to limit OS control
of the Embedded Security Device.
●
Reset of Embedded Security Device through OS (some models) (enable/disable) - This option
allows the user to limit the operating system ability to request a Reset to Factory Settings of
the Embedded Security Device. Changing this setting requires turning the computer off and
then back on.
NOTE: To enable this option, a Setup password must be set.
Table 3-4 Computer Setup—Security (continued)
Computer Setup (F10) Utilities 21