Maintenance & Service Guide HP Compaq 6005 Pro Business PC
© Copyright 2009 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. Microsoft and Windows are trademarks of Microsoft Corporation in the U.S. and other countries. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty.
About This Book WARNING! Text set off in this manner indicates that failure to follow directions could result in bodily harm or loss of life. CAUTION: Text set off in this manner indicates that failure to follow directions could result in damage to equipment or loss of information. NOTE: Text set off in this manner provides important supplemental information.
iv About This Book
Table of contents 1 Product Features Microtower Chassis .............................................................................................................................. 1 Standard Configuration Features ......................................................................................... 1 Front Panel Components ..................................................................................................... 2 Media Card Reader Components ..............................................
Accessing HP Vision Diagnostics ...................................................................................... 28 Survey Tab ........................................................................................................................ 29 Test Tab ............................................................................................................................. 29 Status Tab ..........................................................................................................
HP Web Site Support ......................................................................................................................... 50 Industry Standards ............................................................................................................................. 50 Asset Tracking and Security ............................................................................................................... 50 Password Security ..........................................................
Personal Grounding Methods and Equipment ................................................................... 67 Grounding the Work Area .................................................................................................. 68 Recommended Materials and Equipment .......................................................................... 68 Operating Guidelines ..........................................................................................................................
Power Supply ................................................................................................................................... 111 System Board ................................................................................................................................... 112 Battery .............................................................................................................................................. 113 Type 1 Battery Holder .....................................
Type 1 Battery Holder ...................................................................................................... 166 Type 2 Battery Holder ...................................................................................................... 166 Type 3 Battery Holder ...................................................................................................... 167 External Security Devices ...................................................................................................
Solving Power Problems .................................................................................................................. 204 Solving Hard Drive Problems ........................................................................................................... 205 Solving Media Card Reader Problems ............................................................................................. 208 Solving Display Problems ........................................................................
xii
1 Product Features Microtower Chassis Standard Configuration Features The HP Compaq Microtower features may vary depending on the model. For a complete listing of the hardware and software installed in the computer, run the diagnostic utility (included on some computer models only). Instructions for using the utility are provided in the Troubleshooting Guide.
Front Panel Components Drive configuration may vary by model. Table 1-1 Front Panel Components 1 5.25-inch Optical Drives1 6 Optical Drive Eject Buttons 2 Optical Drive Activity Lights 7 3.5-inch Media Card Reader (optional)2 3 Hard Drive Activity Light 8 Dual-State Power Button 4 Microphone/Headphone Connector 9 Power On Light 5 USB (Universal Serial Bus) 2.
Media Card Reader Components The media card reader is an optional device available on some models only. Refer to the following illustration and table to identify the media card reader components. Figure 1-2 Media Card Reader Components Table 1-2 Media Card Reader Components No.
Rear Panel Components Table 1-3 Rear Panel Components 1 Power Cord Connector 6 Line-Out Connector for powered audio devices (green) 2 Line-In Audio Connector (blue) 7 PS/2 Keyboard Connector (purple) 3 PS/2 Mouse Connector (green) 8 VGA Monitor Connector 4 Serial Connector 9 DisplayPort Monitor Connector 5 RJ-45 Network Connector 10 Universal Serial Bus (USB) NOTE: Arrangement and number of connectors may vary by model.
Serial Number Location Each computer has a unique serial number and product ID number that are located on the top cover of the computer. Keep these numbers available for use when contacting customer service for assistance.
Small Form Factor Standard Configuration Features The HP Compaq Small Form Factor features may vary depending on the model. For a complete listing of the hardware and software installed in the computer, run the diagnostic utility (included on some computer models only). Instructions for using the utility are provided in the Troubleshooting Guide. NOTE: The Small Form Factor computer can also be used in a tower orientation.
Front Panel Components Drive configuration may vary by model. Figure 1-5 Front Panel Components Table 1-4 Front Panel Components 1 5.25-inch Optical Drive1 6 USB (Universal Serial Bus) Ports 2 Optical Drive Activity Light 7 Microphone/Headphone Connector 3 Optical Drive Eject Button 8 3.
Media Card Reader Components The media card reader is an optional device available on some models only. Refer to the following illustration and table to identify the media card reader components. Figure 1-6 Media Card Reader Components Table 1-5 Media Card Reader Components No.
Rear Panel Components Figure 1-7 Rear Panel Components Table 1-6 Rear Panel Components 1 RJ-45 Network Connector 6 DisplayPort Monitor Connector 2 Serial Connector 7 VGA Monitor Connector 3 PS/2 Mouse Connector (green) 8 PS/2 Keyboard Connector (purple) 4 Power Cord Connector 9 Line-Out Connector for powered audio devices (green) 5 Universal Serial Bus (USB) 10 Line-In Audio Connector (blue) NOTE: Arrangement and number of connectors may vary by model.
Serial Number Location Each computer has a unique serial number and product ID number in the location shown below. Keep these numbers available for use when contacting customer service for assistance.
2 Installing and Customizing the Software If your computer was not shipped with a Microsoft operating system, some portions of this documentation do not apply. Additional information is available in online help after you install the operating system. NOTE: If the computer was shipped with Windows Vista or Windows 7 loaded, you will be prompted to register the computer with HP Total Care before installing the operating system. You will see a brief movie followed by an online registration form.
Installing the Operating System The first time you turn on the computer, the operating system is installed automatically. This process takes about 5 to 10 minutes, depending on which operating system is being installed. Carefully read and follow the instructions on the screen to complete the installation. CAUTION: Once the automatic installation has begun, DO NOT TURN OFF THE COMPUTER UNTIL THE PROCESS IS COMPLETE.
Accessing Disk Image (ISO) Files There are disk image files (ISO files) included on your PC that contain the installation software for additional software. These CD image files are located in the folder C:\SWSetup\ISOs. Each .iso file can be burned to CD media to create an installation CD. It is recommended that these disks be created and the software installed in order to get the most from your PC.
3 Computer Setup (F10) Utility Computer Setup (F10) Utilities Use Computer Setup (F10) Utility to do the following: 14 ● Change system default settings. ● Set the system date and time. ● Set, view, change, or verify the system configuration, including settings for processor, graphics, memory, audio, storage, communications, and input devices. ● Modify the boot order of bootable devices such as hard drives, optical drives, or USB flash media devices.
● Replicate the system setup by saving system configuration information on USB flash media device or other storage media emulating a diskette and restoring it on one or more computers. ● Execute self-tests on a specified ATA hard drive (when supported by drive). ● Enable or disable DriveLock security (when supported by drive). Using Computer Setup (F10) Utilities Computer Setup can be accessed only by turning the computer on or restarting the system.
Computer Setup—File NOTE: Support for specific Computer Setup options may vary depending on the hardware configuration.
Computer Setup—Storage NOTE: Support for specific Computer Setup options may vary depending on the hardware configuration. Table 3-3 Computer Setup—Storage Option Description Device Configuration Lists all installed BIOS-controlled storage devices. When a device is selected, detailed information and options are displayed. The following options may be presented. Emulation Type Allows you to select a drive emulation type for a certain storage device.
Table 3-3 Computer Setup—Storage (continued) Option Description Storage Options Removable Media Boot Enables/disables ability to boot the system from removable media. eSATA Port Allows you to enable eSATA support. This causes one of the SATA connectors to become eSATA capable. Max eSATA Speed Allows you to choose 1.5 Gbps or 3.0 Gbps as the maximum eSATA speed. By default, the speed is limited to 1.5 Gbps for maximum reliability. CAUTION: Consult your eSATA drive and cable manufacturer before enabling 3.
Table 3-3 Computer Setup—Storage (continued) Option Description DPS Self-Test Allows you to execute self-tests on ATA hard drives capable of performing the Drive Protection System (DPS) self-tests. NOTE: This selection will only appear when at least one drive capable of performing the DPS self-tests is attached to the system.
Computer Setup—Security NOTE: Support for specific Computer Setup options may vary depending on the hardware configuration. Table 3-4 Computer Setup—Security Option Description Setup Password Allows you to set and enable setup (administrator) password. NOTE: If the setup password is set, it is required to change Computer Setup options, flash the ROM, and make changes to certain plug and play settings under Windows. See the Desktop Management Guide for more information.
Table 3-4 Computer Setup—Security (continued) Option Description Device Security Allows you to set Device Available/Device Hidden for ● Serial ports ● Parallel port ● System audio ● Network controllers (some models) ● Embedded security device (some models) ● SATA0 ● SATA1 ● SATA2 ● SATA3 USB Security Allows you to disable individual or groups of USB ports. Slot Security Allows you to disable PCIe and PCI slots along with cards plugged into them.
Table 3-4 Computer Setup—Security (continued) Option Description System Security (some Data Execution Prevention (some models) (enable/disable) Helps prevent operating system security models: these options breaches. are hardware Virtualization Technology (some models) (enable/disable) Controls the virtualization features of the dependent) processor. Changing this setting requires turning the computer off and then back on.
Computer Setup—Power NOTE: Support for specific Computer Setup options may vary depending on the hardware configuration. Table 3-5 Computer Setup—Power Option Description OS Power Management ● Idle Power Savings—Extended/Normal. Allows certain operating systems to decrease the processors power consumption when the processor is idle.
Computer Setup—Advanced NOTE: Support for specific Computer Setup options may vary depending on the hardware configuration. Table 3-6 Computer Setup—Advanced (for advanced users) Option Description Power-On Options Allows you to set: ● 24 POST mode (QuickBoot, Clear Memory, FullBoot, or FullBoot Every x Days). ◦ QuickBoot = Do not clear memory or perform a memory test. ◦ FullBoot = Memory test (count) on cold boot. Clears memory on all boots.
Table 3-6 Computer Setup—Advanced (for advanced users) (continued) Option Description ◦ Clear Memory = No memory count on cold boot. Clears memory on all boots. ◦ FullBoot Every x Days = Memory count on 1st cold boot on or after the xth day. No more memory counts until 1st cold boot on or after x days. Clears memory on all boots. ● POST messages (enable/disable). ● F9 prompt (enable/disable or hidden/displayed). Enabling this feature will display the text F9 = Boot Menu during POST.
Table 3-6 Computer Setup—Advanced (for advanced users) (continued) Option Description PCI Devices ● Lists currently installed PCI devices and their IRQ settings. ● Allows you to reconfigure IRQ settings for these devices or to disable them entirely. These settings have no effect under an ACPI-based operating system. PCI VGA Configuration Displayed only if there are one or more PCI graphics controllers in the system and the integrated video is enabled.
Table 3-6 Computer Setup—Advanced (for advanced users) (continued) Option Description from being used by the operating system and reduces the power used by the computer in S5. ● Processor cache (enable/disable). ● Multi-Processor (enable/disable). This option may be used to disable multi-processor support under the OS. ● Integrated Graphics Memory Size (Automatic, 32M, 64M, 128M, 256M). This allows the user to control the size of the memory used by the integrated graphics controller.
4 Computer Diagnostic Features Hewlett-Packard Vision Diagnostics NOTE: HP Vision Diagnostics is included on CD with some computer models only. The Hewlett-Packard Vision Diagnostics utility allows you to view information about the hardware configuration of the computer and perform hardware diagnostic tests on the subsystems of the computer. The utility simplifies the process of effectively identifying, diagnosing, and isolating hardware issues.
NOTE: If the system does not boot to the CD in the optical drive or to the USB flash drive, you may need to change the boot order in the Computer Setup (F10) utility. Refer to the Computer Setup (F10) Utility Guide for more information. 5. At the boot menu, select either the HP Vision Diagnostics utility to test the various hardware components in the computer or the HP Memory Test utility to test memory only.
There are three types of tests to choose from: ● Quick Test—Provides a predetermined script where a sample of each hardware component is exercised. You may further modify which of the Quick tests are executed by selecting or deselecting individual tests in the hardware component check list. ● Complete Test—Provides a predetermined script where each hardware component is fully tested.
History Tab The History tab contains information on past test executions. The History Log displays all tests that have been executed, the number of times of execution, the number of times failed, the date each test was executed, and the time it took to complete each test. The Clear History button will clear the contents of the History Log. The contents of the History Log may be saved as a HTML file to either floppy or USB flash drive by clicking the Save button.
The Memory test tab section provides information on the HP Memory Test application that may be launched from the boot menu. The HP Support section provides information on obtaining technical support from HP. Saving and Printing Information in HP Vision Diagnostics You can save the information displayed in the HP Vision Diagnostics Survey, History and Errors tabs to a diskette or a USB flash drive. You can not save to the hard drive.
5 Desktop Management HP Client Management Solutions provides standards-based solutions for managing and controlling desktops, workstations, and notebook PCs in a networked environment. HP pioneered desktop manageability in 1995 with the introduction of the industry’s first fully manageable desktop personal computers. HP is a patent holder of manageability technology.
The best deployment method depends on your information technology environment and processes. ROM-based setup and ACPI hardware provide further assistance with recovery of system software, configuration management and troubleshooting, and power management. HP Client Automation Agent The management agent used by both HP Client Automation Standard and Enterprise Editions is preloaded on the computer. When installed, it enables communication with the HP management console.
● Reports ● Administrative tasks to update HP specific tools HPCM can be downloaded from http://www.symantec.com/business/theme.jsp?themeid=altiris by clicking on HP Client Manager under Strategic Partner Products. A free permanent license can also be obtained from the download page. HPCM “How to” videos are also published on http://www.symantec.com/connect. Search for HP Client Manager 7.0 to view step by step videos for various tasks within HPCM.
● HP Proactive Change Notification ● HP Subscriber's Choice HP Client Management Interface Regardless of the system management tools your IT department uses, managing both your hardware and software assets is important to keeping your IT costs low and your business agile. The IT administrator can access the HP Client Management Interface by writing simple scripts and integrating those scripts to the management solution of their choice.
central file store. SSM then automatically updates any down-revision system software on the networked PCs to the later levels available in the file store. Since SSM only allows distribution of SoftPaq updates to the correct client system models, administrators can confidently and efficiently use SSM to keep system software updated.
HP Client Automation Starter and Standard Editions HP Client Automation is a hardware and software management solution for Windows Vista, Windows XP and HP Thin Client environments that is easy to use and quick to deploy, while providing a strong foundation for future requirements.
● Remotely configure BIOS and security settings ● Automate processes to quickly resolve hardware problems Tight integration with HP Instant Support tools reduces hardware troubleshooting time.
Microsoft products supported by the HP Client Catalog include: ● System Center Configuration Manager 2007 ● System Center Essentials 2007 ● Systems Management Server (SMS) 2003 R2 For more information on HP Client Catalog for SMS, visit http://h20331.www2.hp.com/Hpsub/cache/ 486247-0-0-225-121.html?jumpid=reg_R1002_USEN. Remote Management Technology Models include either vPro technology or standard technology. Both allow for better discovery, healing, and protection of networked computing assets.
Available management technologies include the following: ● AMT (includes DASH 1.0) ● ASF ● DASH 1.1 (using a Broadcom NIC) ASF and AMT may not be configured at the same time, but both are supported. To configure Intel vPro systems for AMT or ASF: 1. Turn on or restart the computer. If you are in Microsoft Windows, click Start > Shut Down > Restart. 2. As soon as the computer is turned on, press the hot key, Ctrl+P, before the computer boots to the operating system.
● ◦ Password Policy ◦ Secure Firmware Update (enable/disable) ◦ Set PRTC ◦ Idle Timeout Change Intel ® ME Password (HP highly recommends that this password be changed. The default password is admin.) In order to remotely manage AMT systems, the administrator must use a remote console that supports AMT. Enterprise management consoles are available from suppliers such as HP, Altiris and Microsoft SMS. In SMB mode, the client provides a Web browser interface.
Retired Solutions Two software packages, Altiris Local Recovery, and Dantz Retrospect, will no longer be shipping on HP business desktops, notebooks, or workstations. ROM Flash The computer's BIOS is stored in a programmable flash ROM (read only memory). By establishing a setup password in the Computer Setup (F10) Utility, you can protect the ROM from being unintentionally updated or overwritten. This is important to ensure the operating integrity of the computer.
Boot Block Emergency Recovery Mode Boot Block Emergency Recovery Mode permits system recovery in the unlikely event of a ROM flash failure. For example, if a power failure were to occur during a BIOS upgrade, the ROM flash would be incomplete. This would render the system BIOS unusable. The Boot Block is a flash-protected section of the ROM that contains code that checks for a valid system BIOS image when the system is turned on. ● If the system BIOS image is valid, the system starts normally.
Replicating the Setup The following procedures give an administrator the ability to easily copy one setup configuration to other computers of the same model. This allows for faster, more consistent configuration of multiple computers. NOTE: Both procedures require a diskette drive or a supported USB flash drive. NOTE: System Software Manager (SSM) can be used to replicate computer setup information from within the Windows operating system. For more information see the SSM User’s Guide at http://www.hp.
NOTE: A bootable diskette is required for this procedure or to create a bootable USB flash media device. If Windows XP is not available to use to create a bootable diskette, use the method for copying to a single computer instead (see Copying to Single Computeron page 45). 1. Create a bootable diskette or USB flash media device. See Supported USB Flash Media Device on page 46 or Unsupported USB Flash Media Device on page 48. CAUTION: Not all computers can be booted from a USB flash media device.
To create a bootable USB flash media device, you must have: ● a supported USB flash media device ● a bootable DOS diskette with the FDISK and SYS programs (If SYS is not available, FORMAT may be used, but all existing files on the USB flash media device will be lost.) ● a PC that is bootable from a USB flash media device CAUTION: Some older PCs may not be bootable from a USB flash media device.
12. Copy any files you saved in step 9 back to your USB flash media device. 13. Remove the diskette and reboot the computer. The computer will boot to the USB flash media device as drive C. NOTE: The default boot order varies from computer to computer, and it can be changed in the Computer Setup (F10) Utility. If you have used a DOS version from Windows 9x, you may see a brief Windows logo screen. If you do not want this screen, add a zero-length file named LOGO.
9. If the system did not automatically restart when exiting FDISK, press Ctrl+Alt+Del to reboot to the DOS diskette. 10. At the A:\ prompt, type FORMAT C: /S and press Enter. Format will format the USB flash media device, add the system files, and ask for a Volume Label. 11. Press Enter for no label or enter one if desired. 12. Turn off the computer and unplug the power cord. Open the computer and re-install any PCI cards that were previously removed. Close the computer cover. 13.
HP Web Site Support HP engineers rigorously test and debug software developed by HP and third-party suppliers, and develop operating system specific support software, to ensure performance, compatibility, and reliability for HP computers. When making the transition to new or revised operating systems, it is important to implement the support software designed for that operating system.
Use the following utilities to manage security settings on the HP computer: ● Locally, using the Computer Setup Utilities. See the Computer Setup (F10) Utility Guide included with the computer for additional information and instructions on using the Computer Setup Utilities. ● Remotely, using HP Client Manager from Symantec, HP Client Automation, or System Software Manager. This software enables the secure, consistent deployment and control of security settings.
Table 5-1 Security Features Overview (continued) Device Security LoJack for HP ProtectTools Allows you to set Device Available/Device Hidden for: ● Serial ports ● Parallel port ● Rear USB ports ● Front USB ports ● Internal USB ports ● System audio ● Network controllers (some models) ● Legacy diskette ● Embedded security device (some models) ● SATA0 ● SATA1 (some models) ● SATA2 (some models) ● SATA3 (some models) ● eSATA (some models) Allows you to remotely monitor, manage, and
Table 5-1 Security Features Overview (continued) Setup Security Level Provides a method to allow end-users limited access to change specified setup options, without having to know the Setup Password. This feature allows the administrator the flexibility to protect changes to essential setup options, while allowing the user to view system settings and configure nonessential options.
Password Security The power-on password prevents unauthorized use of the computer by requiring entry of a password to access applications or data each time the computer is turned on or restarted. The setup password specifically prevents unauthorized access to Computer Setup, and can also be used as an override to the power-on password. That is, when prompted for the power-on password, entering the setup password instead will allow access to the computer.
Entering a Power-On Password To enter a power-on password, complete the following steps: 1. Turn on or restart the computer. If you are in Windows, click Start > Shut Down > Restart the Computer. 2. When the key icon appears on the monitor, type the current password, then press Enter. NOTE: Type carefully; for security reasons, the characters you type do not appear on the screen. If you enter the password incorrectly, a broken key icon appears. Try again.
NOTE: Type carefully; for security reasons, the characters you type do not appear on the screen. 4. Press Enter. The new password takes effect the next time you turn on the computer. NOTE: Refer to the National Keyboard Delimiter Characterson page 56 for information about the alternate delimiter characters. The power-on password and setup password may also be changed using the Security options in Computer Setup.
National Keyboard Delimiter Characters - German - Portuguese * For Bosnia-Herzegovina, Croatia, Montenegro, Serbia, and Slovenia Clearing Passwords If you forget the password, you cannot access the computer. Refer to the Troubleshooting Guide for instructions on clearing passwords. If the system is equipped with an embedded security device, refer to the HP ProtectTools Security Manager Guide at http://www.hp.com.
DriveLock Applications The most practical use of the DriveLock security feature is in a corporate environment. The system administrator would be responsible for configuring the hard drive which would involve, among other things, setting the DriveLock master password and a temporary user password. In the event that the user forgets the user password or the equipment is passed on to another employee, the master password can always be used to reset the user password and regain access to the hard drive.
3. Select Security > Smart Cover > Cover Removal Sensor, and select the desired security level. 4. Before exiting, click File > Save Changes and Exit. Smart Cover Lock The Smart Cover Lock is a software-controllable cover lock featured on some HP computers. This lock prevents unauthorized access to the internal components. Computers ship with the Smart Cover Lock in the unlocked position. CAUTION: For maximum cover lock security, be sure to establish a setup password.
CAUTION: The Smart Cover FailSafe Key is a specialized tool available from HP. Be prepared; order this key before you need one at an authorized reseller or service provider. To obtain the FailSafe Key, do any one of the following: ● Contact an authorized HP reseller or service provider. ● Call the appropriate number listed in the warranty. For more information about using the Smart Cover FailSafe Key, consult the Hardware Reference Guide.
Thermal Sensor The thermal sensor is a hardware and software feature that tracks the internal temperature of the computer. This feature displays a caution message when the normal range is exceeded, which gives you time to take action before internal components are damaged or data is lost. CAUTION: A high temperature condition can result in damage to the system or data loss.
6 Serial ATA Drive Guidelines and Features NOTE: Serial ATA = SATA HP only supports the use of SATA hard drives on these computers. SATA Hard Drives Serial ATA Hard Drive Characteristics Number of pins/conductors in data cable 7/7 Number of pins in power cable 15 Maximum data cable length 39.37 in (100 cm) Data interface voltage differential 400-700 mV Drive voltages 3.3 V, 5 V, 12 V Jumpers for configuring drive N/A Data transfer rate 3.
SATA Hard Drive Cables SATA Data Cable Always use an HP approved SATA 3.0 Gb/s cable as it is fully backwards compatible with the SATA 1.5 Gb/s drives. Current HP desktop products ship with SATA 3.0 Gb/s hard drives. SATA data cables are susceptible to damage if overflexed. Never crease a SATA data cable and never bend it tighter than a 30 mm (1.18 in) radius. The SATA data cable is a thin, 7-pin cable designed to transmit data for only a single drive.
ATA SMART Drives The Self Monitoring Analysis and Recording Technology (SMART) ATA drives for the HP Personal Computers have built-in drive failure prediction that warns the user or network administrator of an impending failure or crash of the hard drive. The SMART drive tracks fault prediction and failure indication parameters such as reallocated sector count, spin retry count, and calibration retry count. If the drive determines that a failure is imminent, it generates a fault alert.
7 Identifying the Chassis, Routine Care, and Disassembly Preparation This chapter provides general service information for the computer. Adherence to the procedures and precautions described in this chapter is essential for proper service. CAUTION: When the computer is plugged into an AC power source, voltage is always applied to the system board. You must disconnect the power cord from the power source before opening the computer to prevent system board or component damage.
Microtower (MT) Electrostatic Discharge Information A sudden discharge of static electricity from your finger or other conductor can destroy static-sensitive devices or microcircuitry. Often the spark is neither felt nor heard, but damage occurs. An electronic device exposed to electrostatic discharge (ESD) may not appear to be affected at all and can work perfectly throughout a normal cycle.
Removing DIPs* from vinyl tray 2,000 V 4,000 V 11,500 V Removing DIPs* from Styrofoam 3,500 V 5,000 V 14,500 V Removing bubble pack from PCB 7,000 V 20,000 V 26,500 V Packing PCBs in foam-lined box 5,000 V 11,000 V 21,000 V *These are then multi-packaged inside plastic tubes, trays, or Styrofoam. NOTE: 700 volts can degrade a product. Preventing Electrostatic Damage to Equipment Many electronic components are sensitive to ESD.
Grounding the Work Area To prevent static damage at the work area, use the following precautions: ● Cover the work surface with approved static-dissipative material. Provide a wrist strap connected to the work surface and properly grounded tools and equipment. ● Use static-dissipative mats, foot straps, or air ionizers to give added protection. ● Handle electrostatic sensitive components, parts, and assemblies by the case or PCB laminate. Handle them only at static-free work areas.
Operating Guidelines To prevent overheating and to help prolong the life of the computer: ● Keep the computer away from excessive moisture, direct sunlight, and extremes of heat and cold. ● Operate the computer on a sturdy, level surface. Leave a 10.2-cm (4-inch) clearance on all vented sides of the computer and above the monitor to permit the required airflow. ● Never restrict the airflow into the computer by blocking any vents or air intakes.
To clean the computer case, follow the procedures described below: ● To remove light stains or dirt, use plain water with a clean, lint-free cloth or swab. ● For stronger stains, use a mild dishwashing liquid diluted with water. Rinse well by wiping it with a cloth or swab dampened with clear water. ● For stubborn stains, use isopropyl (rubbing) alcohol. No rinsing is needed as the alcohol will evaporate quickly and not leave a residue.
Cleaning the Mouse Before cleaning the mouse, ensure that the power to the computer is turned off. ● Clean the mouse ball by first removing the retaining plate and the ball from the housing. Pull out any debris from the ball socket and wipe the ball with a clean, dry cloth before reassembly. ● To clean the mouse body, follow the procedures in Cleaning the Computer Case on page 69.
Cables and Connectors Most cables used throughout the unit are flat, flexible cables. These cables must be handled with care to avoid damage. Apply only the tension required to seat or unseat the cables during insertion or removal from the connector. Handle cables by the connector whenever possible. In all cases, avoid bending or twisting the cables, and ensure that the cables are routed in such a way that they cannot be caught or snagged by parts being removed or replaced.
8 Removal and Replacement Procedures Microtower (MT) Chassis Adherence to the procedures and precautions described in this chapter is essential for proper service. After completing all necessary removal and replacement procedures, run the Diagnostics utility to verify that all components operate properly. NOTE: Not all features listed in this guide are available on all computers.
Preparation for Disassembly See Identifying the Chassis, Routine Care, and Disassembly Preparation on page 65 for initial safety procedures. 1. Remove/disengage any security devices that prohibit opening the computer (External Security Devices on page 116). 2. Close any open software applications. 3. Exit the operating system. 4. Remove any diskette, compact disc, or media card from the computer. 5. Turn off the computer and any peripheral devices that are connected to it.
Access Panel 1. Prepare the computer for disassembly (Preparation for Disassembly on page 74). CAUTION: Before removing the computer access panel, ensure that the computer is turned off and that the power cord is disconnected from the electrical outlet. 2. Loosen the two captive thumbscrews (1) that secure the access panel to the computer chassis. 3. Use the handle located between the thumbscrews to lift the access panel off the unit (2).
Front Bezel 1. Prepare the computer for disassembly (Preparation for Disassembly on page 74). 2. Remove the computer access panel. 3. Lift up the three tabs on the side of the bezel (1), then rotate the bezel off the chassis (2). Figure 8-3 Removing the Front Bezel To reinstall the front bezel, reverse the removal procedure.
Removing Bezel Blanks On some models, there are bezel blanks covering the 3.5-inch and 5.25-inch external drive bays that need to be removed before installing a drive. To remove a bezel blank: 1. Remove the access panel and front bezel. 2. To remove a bezel blank, push the two retaining tabs that hold the bezel blank in place towards the outer right edge of the bezel (1) and slide the bezel blank back and to the right to remove it (2).
Cable Management Always follow good cable management practices when working inside the computer. ● Keep cables away from major heat sources like the heat sink. ● Do not jam cables on top of expansion cards or memory modules. Printed circuit cards like these are not designed to take excessive pressure on them. ● Keep cables clear of sliding or moveable parts to prevent them from being cut or crimped when the parts are moved. ● When folding a flat ribbon cable, never fold to a sharp crease.
Cable Connections System board connectors are color-coded to make it easier to find the proper connection.
Memory The computer comes with double data rate 3 synchronous dynamic random access memory (DDR3SDRAM) dual inline memory modules (DIMMs). The memory sockets on the system board can be populated with up to four industry-standard DIMMs. These memory sockets are populated with at least one preinstalled DIMM. To achieve the maximum memory support, you can populate the system board with up to 16-GB of memory configured in a highperforming dual channel mode.
Figure 8-5 DIMM Socket Locations Table 8-1 DIMM Socket Locations Item Description Socket Color 1 XMM1 socket, Channel A (populate fourth) White 2 XMM2 socket, Channel B (populate third) White 3 XMM3 socket, Channel A (populate second) Black 4 XMM4 socket, Channel B (populate first) Black NOTE: A DIMM must occupy the black XMM4 socket. Otherwise, the system will display a POST error message indicating that a memory module must be installed in the wrong socket.
3. Open both latches of the memory module socket (1), and insert the memory module into the socket (2). Figure 8-6 Installing a DIMM NOTE: A memory module can be installed in only one way. Match the notch on the module with the tab on the memory socket. A DIMM must occupy the XMM4 socket. Always populate XMM4 before XMM2, and XMM3 before XMM1 (populate the black sockets before white sockets in each channel). A DIMM must occupy the black DIMM1 socket.
Expansion Cards The computer has one PCI expansion slot, two PCI Express x1 expansion slots, and one PCI Express x16 expansion slot. Figure 8-7 Expansion Slot Locations Table 8-2 Expansion Slot Locations Item Description 1 PCI expansion slot 2 PCI Express x16 expansion slot 3 PCI Express x1 expansion slot 4 PCI Express x1 expansion slot NOTE: You can install a PCI Express x1, x4, x8, or x16 expansion card in the PCI Express x16 slot. To remove, replace, or add an expansion card: 1.
4. Release the slot cover retention latch that secures the PCI slot covers by lifting the green tab on the latch and rotating the latch to the open position. Figure 8-8 Opening the Expansion Slot Retainer 5. Before installing an expansion card, remove the expansion slot cover or the existing expansion card. NOTE: Before removing an installed expansion card, disconnect any cables that may be attached to the expansion card. a.
b. If you are removing a standard PCI card or PCI Express x1 card, hold the card at each end, and carefully rock it back and forth until the connectors pull free from the socket. Pull the expansion card straight up from the socket then away from the inside of the chassis to release it from the chassis frame. Be sure not to scrape the card against the other components. Figure 8-10 Removing a Standard PCI Expansion Card c.
7. If you are not installing a new expansion card, install an expansion slot cover to close the open slot. CAUTION: After removing an expansion card, you must replace it with a new card or expansion slot cover for proper cooling of internal components during operation. 8.
10. Connect external cables to the installed card, if needed. Connect internal cables to the system board, if needed. 11. Reconfigure the computer, if necessary. Refer to the Computer Setup (F10) Utility Guide for instructions on using Computer Setup. Drive Positions Figure 8-14 Drive Positions 1 Two 5.25-inch external drive bays for optional drives (optical drives shown) 2 One 3.5-inch external drive bay for optional drive (media card reader shown) 3 Secondary 3.
Installing and Removing Drives When installing additional drives, follow these guidelines: ● The primary Serial ATA (SATA) hard drive must be connected to the dark blue primary SATA connector on the system board labeled SATA0. ● Connect a SATA optical drive to the white SATA connector on the system board labeled SATA1. ● Connect devices in order of SATA0, SATA1, SATA2, then SATA3. ● Connect an eSATA adapter cable to the orange SATA3 connector.
CAUTION: To prevent loss of work and damage to the computer or drive: If you are inserting or removing a drive, shut down the operating system properly, turn off the computer, and unplug the power cord. Do not remove a drive while the computer is on or in standby mode. Before handling a drive, ensure that you are discharged of static electricity. While handling a drive, avoid touching the connector. Handle a drive carefully; do not drop it. Do not use excessive force when inserting a drive.
System Board Drive Connections Refer to the following illustration and table to identify the system board drive connectors. Figure 8-16 System Board Drive Connections Table 8-3 System Board Drive Connections No.
Removing an External 5.25-inch or 3.5-inch Drive CAUTION: computer. All removable media should be taken out of a drive before removing the drive from the 1. Prepare the computer for disassembly (Preparation for Disassembly on page 74). 2. Remove the access panel (Access Panel on page 75). WARNING! To reduce risk of personal injury from hot surfaces, allow the internal system components to cool before touching. 3. Remove the front bezel (Front Bezel on page 76). 4.
b. If you are removing a media card reader, disconnect the USB cable from the system board. If the media card reader has a 1394 port, disconnect the 1394 cable from the PCI card.
5. A latch drive bracket with release tabs secures the drives in the drive bay. Lift the release tab on the latch drive bracket (1) for the drive you want to remove, then slide the drive from its drive bay (2). Figure 8-20 Removing the External Drives 6. Remove the four guide screws (two on each side) from the old drive. You will need these screws to install a new drive.
Installing an External 5.25-inch or 3.5-inch Drive NOTE: The system does not support Parallel ATA (PATA) optical drives. 1. Prepare the computer for disassembly (Preparation for Disassembly on page 74). 2. Remove the access panel (Access Panel on page 75). WARNING! To reduce risk of personal injury from hot surfaces, allow the internal system components to cool before touching. 3. Remove the front bezel (Front Bezel on page 76). 4.
6. Slide the drive into the drive bay, making sure to align the guide screws with the guide slots, until the drive snaps into place. Figure 8-22 Sliding the External Drives into the Drive Cage 7. Connect the power and data cables to the drive as indicated in the following illustrations. a. If you are installing an optical drive, connect the power cable (1) and data cable (2) to the back of the drive.
b. If you are installing a media card reader, connect the USB cable to the system board. If the media card reader has a 1394 port, connect the 1394 cable to the PCI card. Figure 8-24 Connecting the Media Card Reader USB Cable Figure 8-25 Connecting the Media Card Reader 1394 Cable 8. If installing a new drive, connect the opposite end of the data cable to the appropriate system board connector.
Removing an Internal 3.5-inch Hard Drive NOTE: Before you remove the old hard drive, be sure to back up the data from the old hard drive so that you can transfer the data to the new hard drive. 1. Prepare the computer for disassembly (Preparation for Disassembly on page 74). 2. Remove the access panel (Access Panel on page 75). WARNING! To reduce risk of personal injury from hot surfaces, allow the internal system components to cool before touching. 3.
Installing an Internal 3.5-inch Hard Drive NOTE: The system does not support Parallel ATA (PATA) hard drives. 1. Prepare the computer for disassembly (Preparation for Disassembly on page 74). 2. Remove the access panel (Access Panel on page 75). WARNING! To reduce risk of personal injury from hot surfaces, allow the internal system components to cool before touching. 3. Install the four guide screws (two on each side) that were removed from the old drive into the new drive.
5. Connect the power cable (1) and data cable (2) to the back of the hard drive. Figure 8-30 Connecting the Hard Drive Cables CAUTION: Never crease or bend a SATA data cable tighter than a 30 mm (1.18 in) radius. A sharp bend can break the internal wires. 6. If installing a new drive, connect the opposite end of the data cable to the appropriate system board connector.
2. Remove the screw from the rear of the carrier (1) and slide the top cover off the carrier (2). Figure 8-31 Removing the Carrier Cover 3. Remove the adhesive strip that secures the thermal sensor to the top of the hard drive (1) and move the thermal sensor away from the carrier (2).
4. Remove the four screws from the bottom of the hard drive carrier. Figure 8-33 Removing the Security Screws 5. Slide the hard drive back to disconnect it from the carrier then lift it up and out of the carrier.
6. Place the new hard drive in the carrier then slide the hard drive back so that it seats in the SATA connector on the carrier's circuit board. Be sure the connector on the hard drive is pressed all the way into the connector on the carrier's circuit board. Figure 8-35 Replacing the Hard Drive 7. Replace the four screws in the bottom of the carrier to hold the drive securely in place.
8. Place the thermal sensor on top of the hard drive in a position that does not cover the label (1) and attach the thermal sensor to the top of the hard drive with the adhesive strip (2). Figure 8-37 Replacing the Thermal Sensor 9. Slide the cover on the carrier (1) and replace the screw on the rear of the carrier to secure the cover in place (2). Figure 8-38 Replacing the Carrier Cover 10. Slide the hard drive carrier into the enclosure on the computer and lock it with the key provided.
Fan/Baffle Assembly 1. Prepare the computer for disassembly (Preparation for Disassembly on page 74). 2. Remove the access panel (Access Panel on page 75). 3. Unplug the fan cable from the system board (CHFAN1, P9). 4. Press the lever that secures the assembly to the chassis (1), pivot the assembly forward toward the front of the computer (2), and then lift the assembly straight up and out of the computer (3). To reinstall the fan/baffle, reverse the removal procedure.
Front I/O Assembly 1. Prepare the computer for disassembly (Preparation for Disassembly on page 74). 2. Remove the computer access panel (Access Panel on page 75). 3. Remove the front bezel (Front Bezel on page 76). 4. Remove the cables from the clip on top of the baffle. 5. Disconnect the three front I/O cables (yellow, green, and blue) from the system board connectors (FRNT_USB1, FRNT_USB2, and FRNT_AUD). 6. Remove the silver T15 screw (1) that secures the assembly to the chassis. 7.
Power Switch/LED Assembly 1. Prepare the computer for disassembly (Preparation for Disassembly on page 74). 2. Remove the access panel (Access Panel on page 75). 3. Remove the front bezel (Front Bezel on page 76). 4. Disconnect the cable from the system board (P5, PB/LED). 5. With the computer on its side, press on the bottom of the assembly (1) and rotate upward (2) to disengage it from the chassis. 6.
Heat sink WARNING! To reduce risk of personal injury from hot surfaces, allow the internal system components to cool before touching. 1. Prepare the computer for disassembly (Preparation for Disassembly on page 74). 2. Remove the computer access panel (Access Panel on page 75). 3. Loosen the four silver T15 captive screws that secure the heat sink to the system board.
Processor 1. Prepare the computer for disassembly (Preparation for Disassembly on page 74). 2. Remove the access panel (Access Panel on page 75). 3. Remove the heat sink (Heat sink on page 107). 4. Rotate the locking lever to its full open position (1). 5. Carefully lift the processor from the socket (2). CAUTION: Do NOT handle the pins in the processor socket. These pins are very fragile and handling them could cause irreparable damage.
CAUTION: heat sink retaining screws should be tightened in diagonally opposite pairs (as in an X) to evenly seat the heat sink on the processor. This is especially important as the pins on the socket are very fragile and any damage to them may require replacing the system board. NOTE: After installing a new processor onto the system board, always update the system ROM to ensure that the latest version of the BIOS is being used on the computer.
Rear Chassis Fan 1. Prepare the computer for disassembly (Preparation for Disassembly on page 74). 2. Remove the access panel (Access Panel on page 75). 3. Disconnect the fan control cable from the system board (CHFAN2). 4. Remove the four silver Phillips screws that secure the fan to the chassis. 5. Lift the fan out of the chassis. To install the fan assembly, reverse the removal procedure. Be sure to orient the air flow out of the unit.
Power Supply 1. Prepare the computer for disassembly (Preparation for Disassembly on page 74). 2. Remove the access panel (Access Panel on page 75). 3. Disconnect all power cables from the drives and from the system board. 4. Remove the four silver T15 screws that connect the power supply to the chassis. 5. Press the tab on the base pan in front of the power supply that holds it in place. 6.
System Board 1. Prepare the computer for disassembly (Preparation for Disassembly on page 74). 2. Remove the access panel (Access Panel on page 75). 3. Remove all expansion boards (Expansion Cards on page 83). 4. Disconnect all cables connected to the system board, noting their location for reinstallation. 5. Remove the heat sink (Heat sink on page 107). 6. Remove the eight screws that secure the system board to the chassis. 7.
Battery The battery that comes with the computer provides power to the real-time clock. When replacing the battery, use a battery equivalent to the battery originally installed in the computer. The computer comes with a 3-volt lithium coin cell battery. WARNING! The computer contains an internal lithium manganese dioxide battery. There is a risk of fire and burns if the battery is not handled properly. To reduce the risk of personal injury: Do not attempt to recharge the battery.
Type 1 Battery Holder 1. Lift the battery out of its holder. 2. Slide the replacement battery into position, positive side up. 3. The battery holder automatically secures the battery in the proper position. 4. Replace the computer access panel. 5. Plug in the computer and turn on power to the computer. 6. Reset the date and time and any special system setups using Computer Setup. Refer to the Computer Setup (F10) Utility Guide. Type 2 Battery Holder 1.
4. Plug in the computer and turn on power to the computer. 5. Reset the date and time and any special system setups using Computer Setup. Refer to the Computer Setup (F10) Utility Guide. Type 3 Battery Holder 1. Pull back on the clip (1) that holds the battery in place, then remove the battery (2). 2. Insert the new battery and position the clip back in place. 3. Replace the computer access panel. 4. Plug in the computer and turn on power to the computer. 5.
External Security Devices The following security devices are used to prevent unauthorized access to the internal components of the computer and/or secure the computer to a fixed object.
HP Business PC Security Lock 1. Fasten the security cable by looping it around a stationary object. Figure 8-41 Securing the Cable to a Fixed Object 2. Thread the keyboard and mouse cables through the lock.
3. Screw the lock to the chassis using the screw provided. Figure 8-43 Attaching the Lock to the Chassis 4. Insert the plug end of the security cable into the lock (1) and push the button in (2) to engage the lock. Use the key provided to disengage the lock. Figure 8-44 Engaging the Lock Front Bezel Security The front bezel can be locked in place by installing a security screw provided by HP. To install the security screw: 1.
4. Remove the security screw from the inside of the front bezel. Figure 8-45 Retrieving the Front Bezel Security Screw 5. Replace the front bezel. 6. Install the screw through the interior of the front of the chassis into the front bezel. The screw hole is located toward the middle of the right edge of the chassis between the hard drive bay and speaker.
9 Removal and Replacement Procedures Small Form Factor (SFF) Chassis Adherence to the procedures and precautions described in this chapter is essential for proper service. After completing all necessary removal and replacement procedures, run the Diagnostics utility to verify that all components operate properly. NOTE: Not all features listed in this guide are available on all computers.
Access Panel 1. Prepare the computer for disassembly (Preparation for Disassembly on page 120). 2. Lift up on the access panel handle (1) then lift the access panel off the computer (2). Figure 9-1 Removing the Access Panel To install the access panel, reverse the removal procedure.
Front Bezel 1. Prepare the computer for disassembly (Preparation for Disassembly on page 120). 2. Remove the access panel (Access Panel on page 121). 3. Lift up the three tabs on the side of the bezel (1), then rotate the bezel off the chassis (2). Figure 9-2 Removing the Front Bezel To install the front bezel, reverse the removal procedure.
Bezel Blanks On some models, there are bezel blanks covering the 3.5-inch and 5.25-inch external drive bays that need to be removed before installing a drive. To remove a bezel blank: 1. Remove the access panel (Access Panel on page 121). 2. Remove the front bezel (Front Bezel on page 122).. 3. To remove a bezel blank, push the two retaining tabs that hold the bezel blank in place towards the outer right edge of the bezel (1) and slide the bezel blank back and to the right to remove it (2).
Installing Additional Memory The computer comes with double data rate 3 synchronous dynamic random access memory (DDR3SDRAM) dual inline memory modules (DIMMs). DIMMs The memory sockets on the system board can be populated with up to four industry-standard DIMMs. These memory sockets are populated with at least one preinstalled DIMM. To achieve the maximum memory support, you can populate the system board with up to 16-GB of memory configured in a highperforming dual channel mode.
Populating DIMM Sockets There are four DIMM sockets on the system board, with two sockets per channel. The sockets are labeled XMM1, XMM2, XMM3, and XMM4. Sockets XMM1 and XMM3 operate in memory channel A. Sockets XMM2 and XMM4 operate in memory channel B.
1. Prepare the computer for disassembly (Preparation for Disassembly on page 120). 2. Remove the access panel (Access Panel on page 121). 3. Rotate up the external drive bay housing to access the memory module sockets on the system board.
4. Open both latches of the memory module socket (1), and insert the memory module into the socket (2). Figure 9-6 Installing a DIMM NOTE: A memory module can be installed in only one way. Match the notch on the module with the tab on the memory socket. A DIMM must occupy the black DIMM1 socket. Populate the DIMM sockets in the following order: DIMM1, DIMM3, DIMM2, then DIMM4.
Expansion Cards The computer has one PCI expansion slot, two PCI Express x1 expansion slots, and one PCI Express x16 expansion slot. NOTE: The PCI and PCI Express slots support only low profile cards.
4. Release the slot cover retention latch that secures the PCI slot covers by lifting the green tab on the latch and rotating the latch to the open position. Figure 9-8 Opening the Expansion Slot Retainer 5. Before installing an expansion card, remove the expansion slot cover or the existing expansion card. a. If you are installing an expansion card in a vacant socket, remove the appropriate expansion slot cover on the back of the chassis.
b. If you are removing a standard PCI card or PCI Express x1 card, hold the card at each end, and carefully rock it back and forth until the connectors pull free from the socket. Pull the expansion card straight up from the socket then away from the inside of the chassis to release it from the chassis frame. Be sure not to scrape the card against the other components. NOTE: Before removing an installed expansion card, disconnect any cables that may be attached to the expansion card.
6. Store the removed card in anti-static packaging. 7. If you are not installing a new expansion card, install an expansion slot cover to close the open slot. CAUTION: After removing an expansion card, you must replace it with a new card or expansion slot cover for proper cooling of internal components during operation. 8.
9. Rotate the slot cover retention latch back in place to secure the expansion card. Figure 9-13 Closing the Expansion Slot Retainer 10. Connect external cables to the installed card, if needed. Connect internal cables to the system board, if needed. 11. Reconfigure the computer, if necessary. Refer to the Computer Setup (F10) Utility Guide for instructions on using Computer Setup.
Cable Management The Small Form Factor chassis is a very compact computer and proper routing of the internal cables is critical to the operation of the computer. Follow good cable management practices when working inside the computer. ● Keep cables away from major heat sources like the heat sink. ● Do not jam cables on top of expansion cards or memory modules. Printed circuit cards like these are not designed to take excessive pressure on them.
Cable Connections System board connectors are color-coded to make it easier to find the proper connection.
Drive Positions Figure 9-15 Drive Positions Table 9-3 Drive Positions 1 3.5-inch internal hard drive bay 2 3.5-inch external drive bay for optional drives (media card reader shown) 3 5.25-inch external drive bay for optional drives (optical drive shown) NOTE: The drive configuration on your computer may be different than the drive configuration shown above. To verify the type, size, and capacity of the storage devices installed in the computer, run Computer Setup.
Installing and Removing Drives When installing additional drives, follow these guidelines: ● The primary Serial ATA (SATA) hard drive must be connected to the dark blue primary SATA connector on the system board labeled SATA0. ● Connect a SATA optical drive to the white SATA connector on the system board labeled SATA1. ● Connect devices in order of SATA0, SATA1, SATA2, then SATA3 ● Connect an eSATA adapter cable to the orange SATA3 connector.
CAUTION: To prevent loss of work and damage to the computer or drive: If you are inserting or removing a drive, shut down the operating system properly, turn off the computer, and unplug the power cord. Do not remove a drive while the computer is on or in standby mode. Before handling a drive, ensure that you are discharged of static electricity. While handling a drive, avoid touching the connector. Handle a drive carefully; do not drop it. Do not use excessive force when inserting a drive.
System Board Drive Connections Refer to the following illustration and table to identify the system board drive connectors. Figure 9-17 System Board Drive Connections Table 9-4 System Board Drive Connections No.
Removing an External 5.25-inch Drive CAUTION: computer. All removable media should be taken out of a drive before removing the drive from the To remove a 5.25-inch external drive: 1. Prepare the computer for disassembly (Preparation for Disassembly on page 120). 2. Remove the access panel (Access Panel on page 121). 3. Rotate the drive cage to its upright position. Figure 9-18 Rotating the Drive Cage Up 4.
5. Rotate the drive cage back down to its normal position. CAUTION: Be careful not to pinch any cables or wires when rotating the drive cage down. Figure 9-20 Rotating the Drive Cage Down 6. Press down on the green drive retainer button located on the left side of the drive to disengage the drive from the drive cage (1). While pressing the drive retainer button, slide the drive back until it stops, then lift it up and out of the drive cage (2). Figure 9-21 Removing the 5.
4. Install four M3 metric guide screws in the lower holes on each side of the drive. HP has provided four extra M3 metric guide screws on the front of the chassis, under the front bezel. The M3 metric guide screws are black. Refer to Installing and Removing Drives on page 136 for an illustration of the extra M3 metric guide screws location. CAUTION: Use only 5-mm long screws as guide screws. Longer screws can damage the internal components of the drive.
6. Rotate the drive cage to its upright position. Figure 9-24 Rotating the Drive Cage Up 7. Connect the SATA data cable to the white system board connector labeled SATA1. 8. Route the data cable through the cable guides. CAUTION: There are two cable guides that keep the data cable from being pinched by the drive cage when raising or lowering it. One is located on the bottom side of the drive cage. The other is located on the chassis frame under the drive cage.
10. Rotate the drive cage back down to its normal position. CAUTION: Be careful not to pinch any cables or wires when rotating the drive cage down. Figure 9-26 Rotating the Drive Cage Down 11. Replace the access panel. The system automatically recognizes the drive and reconfigures the computer. Removing an External 3.5-inch Drive CAUTION: computer. All removable media should be taken out of a drive before removing the drive from the The 3.5-inch drive is located underneath the 5.25-inch drive.
2. Disconnect the drive cables from the rear of the drive, or, if you are removing a media card reader, disconnect the USB and 1394 cables from the system board as indicated in the following illustrations. NOTE: On some models, the media card reader does not include a 1394 port or cable.
3. Press down on the green drive retainer button located on the left side of the drive to disengage the drive from the drive cage (1). While pressing the drive retainer button, slide the drive back until it stops, then lift it up and out of the drive cage (2). Figure 9-29 Removing a 3.5-inch Drive (Media Card Reader Shown) NOTE: To replace the 3.5-inch drive, reverse the removal procedure. When replacing a 3.5-inch drive, transfer the four guide screws from the old drive to the new one.
3. Position the guide screws on the drive into the J-slots in the drive bay. Then slide the drive toward the front of the computer until it locks into place. Figure 9-30 Installing a Drive into the 3.5-inch Drive Bay (Media Card Reader Shown) 4. Connect the appropriate drive cables: a.
Removing and Replacing the Primary 3.5-inch Internal SATA Hard Drive NOTE: The system does not support Parallel ATA (PATA) hard drives. Before you remove the old hard drive, be sure to back up the data from the old hard drive so that you can transfer the data to the new hard drive. The preinstalled 3.5-inch hard drive is located under the power supply. To remove and replace the hard drive: 1. Prepare the computer for disassembly (Preparation for Disassembly on page 120). 2.
4. Rotate the power supply to its upright position. The hard drive is located beneath the power supply. Figure 9-32 Raising the Power Supply 5. Disconnect the power cable (1) and data cable (2) from the back of the hard drive.
6. Press down on the green release latch next to the hard drive (1). While holding the latch down, slide the drive forward until it stops, then lift the drive up and out of the bay (2). Figure 9-34 Removing the Hard Drive 7. To install a hard drive, you must transfer the silver and blue isolation mounting guide screws from the old hard drive to the new hard drive.
8. Align the guide screws with the slots on the chassis drive cage, press the hard drive down into the bay, then slide it back until it stops and locks in place. Figure 9-36 Installing the Hard Drive 9. Connect the power and data cables to the back of the hard drive. NOTE: When replacing the primary hard drive, be sure to route the SATA and power cables through the cable guide on the bottom of the chassis frame behind the hard drive.
Removing and Replacing a Removable 3.5-inch SATA Hard Drive Some models are equipped with a removable SATA Hard Drive Enclosure in the 5.25-inch external drive bay. The hard drive is housed in a carrier that can be quickly and easily removed from the drive bay. To remove and replace a drive in the carrier: NOTE: Before you remove the old hard drive, be sure to back up the data from the old hard drive so that you can transfer the data to the new hard drive. 1.
4. Remove the four screws from the bottom of the hard drive carrier. Figure 9-39 Removing the Security Screws 5. Slide the hard drive back to disconnect it from the carrier then lift it up and out of the carrier.
6. Place the new hard drive in the carrier then slide the hard drive back so that it seats in the SATA connector on the carrier's circuit board. Be sure the connector on the hard drive is pressed all the way into the connector on the carrier's circuit board. Figure 9-41 Replacing the Hard Drive 7. Replace the four screws in the bottom of the carrier to hold the drive securely in place.
8. Place the thermal sensor on top of the hard drive in a position that does not cover the label (1) and attach the thermal sensor to the top of the hard drive with the adhesive strip (2). Figure 9-43 Replacing the Thermal Sensor 9. Slide the cover on the carrier (1) and replace the screw on the rear of the carrier to secure the cover in place (2). Figure 9-44 Replacing the Carrier Cover 10. Slide the hard drive carrier into the enclosure on the computer and lock it with the key provided.
Baffle 1. Prepare the computer for disassembly (Preparation for Disassembly on page 120). 2. Remove the access panel (Access Panel on page 121). 3. Remove the cable from the arm that extends from the side of the baffle (1). 4. Lift the baffle straight up out of the chassis (2). Figure 9-45 Removing the baffle To install the baffle, reverse the removal procedure.
Front Fan Assembly 1. Prepare the computer for disassembly (Preparation for Disassembly on page 120). 2. Remove the access panel (Access Panel on page 121). 3. Remove the front bezel (Front Bezel on page 122). 4. Remove the baffle (Baffle on page 155). 5. Disconnect the fan cable from the system board (CH FAN1, P9). 6. On the front of the computer, press the left and bottom tabs to disengage the fan assembly from the chassis. Figure 9-46 Removing the chassis fan 7.
Front I/O/Power Switch Assembly 1. Prepare the computer for disassembly (Preparation for Disassembly on page 120). 2. Remove the access panel (Access Panel on page 121). 3. Remove the front bezel (Front Bezel on page 122). 4. Remove the front fan assembly (Front Fan Assembly on page 156). 5. Remove the black T15 screw (1) that secures the assembly to the chassis. Figure 9-47 Removing the front I/O device/power switch 6. Rotate the drive cage to its upright position. 7.
8. While holding the body of the assembly, pull the assembly away from the front of the computer while guiding the cables through the hole in the drive cage (3). Figure 9-49 Guiding the wires through the drive cage 9. Remove the assembly from the chassis. To reinstall the front I/O/power supply assembly, reverse the removal procedure.
Speaker 1. Prepare the computer for disassembly (Preparation for Disassembly on page 120). 2. Remove the access panel (Access Panel on page 121). 3. Remove the front bezel (Front Bezel on page 122). 4. Rotate the drive cage to its upright position. 5. Disconnect the speaker wire from the system board (SPRK, P5). 6. Remove the two screws that secure the speaker to the chassis. Figure 9-50 Removing the speaker 7. Lift the speaker from the inside of the chassis to remove it.
Heat sink 1. Prepare the computer for disassembly (Preparation for Disassembly on page 120). 2. Remove the access panel (Access Panel on page 121). 3. Remove the baffle (Baffle on page 155). 4. Remove the front fan assembly (Front Fan Assembly on page 156). 5. Loosen the four captive screws that secure the heat sink to the system board tray. CAUTION: Heat sink retaining screws should be removed in diagonally opposite pairs (as in an X) to even the downward forces on the processor.
Processor 1. Prepare the computer for disassembly (Preparation for Disassembly on page 120). 2. Remove the access panel (Access Panel on page 121). 3. Remove the fan shroud (Baffle on page 155). 4. Remove the heat sink (Heat sink on page 160). 5. Rotate the locking lever to its full open position (1). 6. Carefully lift the processor from the socket (2). CAUTION: Do NOT handle the pins in the processor socket. These pins are very fragile and handling them could cause irreparable damage.
4. Apply the thermal grease provided in the spares kit to the top of the processor and install the heat sink atop the processor. 5. Go to step 7. 6. If using a new heat sink, remove the protective covering from the bottom of the heat sink and place it in position atop the processor. 7. Secure the heat sink to the system board and system board tray with the four captive screws and attach the heat sink control cable to the system board.
6. Rotate the power supply to its full upright position (1), pull the power supply forward (2) until the posts on the power supply move forward in the power supply bracket (3), and then lift the power supply straight up and out of the chassis. Figure 9-53 Removing the power supply To install the power supply, reverse the removal procedure.
System Board 1. Prepare the computer for disassembly (Preparation for Disassembly on page 120). 2. Remove the access panel (Access Panel on page 121). 3. Remove all PCI and PCI Express expansion boards (Expansion Cards on page 128). 4. Remove the baffle from the chassis (Baffle on page 155). 5. Remove the fan from the chassis (Front Fan Assembly on page 156). 6. Rotate the drive cage to its upright position. 7. Rotate the power supply to its full upright position. 8.
CAUTION: Before reinstalling the heat sink you must clean the top of the processor and the bottom of the heat sink with an alcohol pad supplied in the spares kit. After the alcohol has evaporated, apply thermal grease to the top of the processor from the syringe supplied in the spares kit. CAUTION: When reconnecting the cables it is important that they be positioned so they do not interfere with the rotation of the drive cage or power supply.
Type 1 Battery Holder 1. Lift the battery out of its holder. Figure 9-55 Removing the battery from a type 1 holder 2. Slide the replacement battery into position, positive side up. 3. The battery holder automatically secures the battery in the proper position. 4. Replace the computer access panel. 5. Plug in the computer and turn on power to the computer. 6. Reset the date and time, your passwords, and any special system setups, using Computer Setup.
4. Plug in the computer and turn on power to the computer. 5. Reset the date and time, your passwords, and any special system setups, using Computer Setup. Refer to the Computer Setup (F10) Utility Guide. Type 3 Battery Holder 1. Pull back on the clip (1) that holds the battery in place, then remove the battery (2). 2. Insert the new battery and position the clip back in place. Figure 9-57 Removing the battery from a type 3 holder 3. Replace the computer access panel. 4.
External Security Devices The following security devices are used to prevent unauthorized access to the internal components of the computer and/or secure the computer to a fixed object. NOTE: For information on data security features, refer to the Computer Setup (F10) Utility Guide, the Desktop Management Guide, and the HP ProtectTools Security Manager Guide (some models) at http://www.hp.com.
Padlock Figure 9-59 Installing a Padlock HP Business PC Security Lock 1. Fasten the security cable by looping it around a stationary object.
2. Thread the keyboard and mouse cables through the lock. Figure 9-61 Threading the Keyboard and Mouse Cables 3. Screw the lock to the chassis using the screw provided.
4. Insert the plug end of the security cable into the lock (1) and push the button in (2) to engage the lock. Use the key provided to disengage the lock. Figure 9-63 Engaging the Lock Front Bezel Security The front bezel can be locked in place by installing a security screw provided by HP. To install the security screw: 1. Prepare the computer for disassembly (Preparation for Disassembly on page 120). 2. Remove the access panel (Access Panel on page 121). 3.
6. Install the security screw next to the middle front bezel release tab to secure the front bezel in place. Figure 9-65 Installing the Front Bezel Security Screw 7. Replace the access panel.
Using the Small Form Factor Computer in a Tower Orientation The Small Form Factor computer can be used in a tower orientation with an optional tower stand that can be purchased from HP. 1. Remove/disengage any security devices that prohibit opening the computer. 2. Remove all removable media, such as compact discs or USB flash drives, from the computer. 3. Turn off the computer properly through the operating system, then turn off any external devices. 4.
A Connector Pin Assignments This appendix contains the pin assignments for many computer and workstation connectors. Some of these connectors may not be used on the product being serviced.
Ethernet RJ-45 Connector and Icon Pin Signal 1 (+) Transmit Data 2 (-) Transmit Data 3 (+) Receive Data 4 Unused 5 Unused 6 (-) Receive Data 7 Unused 8 Unused Serial Interface, Powered and Non-Powered Connector and Icon Pin Signal 1 Carrier Detect (12V if powered) 2 Receive Data 3 Transmit Data 4 Data Terminal Ready 5 Signal Ground 6 Data Set Ready 7 Request to Send 8 Clear to Send 9 Ring Indicator (5V if powered) Pin Signal 1 +5 VDC 2 - Data 3 + Data 4 Groun
Microphone Connector and Icon (1/8” miniphone) 1 2 3 Pin Signal 1 (Tip) Audio_left 2 (Ring) Audio_Right 3 (Shield) Ground Pin Signal 1 (Tip) Audio_left 2 (Ring) Power_Right 3 (Shield) Ground Pin Signal 1 (Tip) Audio_In_Left 2 (Ring) Audio_In_Right 3 (Shield) Ground Pin Signal 1 (Tip) Audio_Out_Left 2 (Ring) Audio_Out_Right 3 (Shield) Ground Headphone Connector and Icon (1/8” miniphone) 1 2 3 Line-in Audio Connector and Icon (1/8” miniphone) 1 2 3 Line-out Audio Connecto
Monitor Connector and Icon Pin Signal Pin Signal 1 Red Analog 9 +5V (fused) 2 Green Analog 10 Ground 3 Blue Analog 11 Not used 4 Not used 12 DDC Serial Data 5 Ground 13 Horizontal Sync 6 Ground 14 Vertical Sync 7 Ground 15 DDC Serial Clock 8 Ground 4-Pin Power (for CPU) Connector and Icon Pin Signal 1 GND 2 GND 3 +12V CPU 4 -12V CPU Monitor 177
SATA Data and Power Drive Connector Pin Signal Pin Signal Pin Signal Pin Signal S1 Ground S2 A+ S3 A- S4 Ground S5 B- S6 B+ S7 Ground P1 Ground P2 V 3.3 P3 V 3.
51 GND 56 PERp9 61 PERn10 66 GND 71 GND 52 PERp8 57 PERn9 62 GND 67 GND 72 PERp13 53 PERN8 58 GND 63 GND 68 PERp12 73 PERn13 54 GND 59 GND 64 PERp11 69 PERn12 74 GND 55 GND 60 PERp10 65 PERn11 70 GND 75 GND 76 PERp14 81 PERn15 77 PERn14 82 GND 78 GND 79 GND 80 PERp15 Pin B information is on the next page NOTE: x1 PCI Express uses pins 1-18 x4 PCI Express uses pins 1-32 x8 PCI Express uses pins 1-49 x16 PCI Express uses pins 1-8 PCI Express x
26 GND 31 PRSNT2# 36 GND 41 PETp6 46 PETn7 27 PETp3 32 GND 37 PETp5 42 PRTn6 47 GND 28 PETn3 33 PETp4 38 PETn5 43 GND 48 PRSNT2# 29 GND 34 PETn4 39 GND 44 GND 49 GND 30 RSVD 35 GND 40 GND 45 PETp7 50 PETp8 51 PETn8 56 GND 61 GND 66 PETp12 71 PETn13 52 GND 57 GND 62 PETp11 67 PETn12 72 GND 53 GND 58 PETp10 63 PETn11 68 GND 73 GND 54 PETp9 59 PETn10 64 GND 69 GND 74 PETp14 55 PETn9 60 GND 65 GND 70 PETp13 75 PET
DVI Connector Connector and Icon Pin Signal Pin Signal 1 T.M.D.S. Data2– 13 T.M.D.S. Data3+ 2 T.M.D.S. Data2+ 14 +5V Power 3 T.M.D.S. Data2/4 Shield 15 Ground (for +5V) 4 T.M.D.S. Data4– 16 Hot Pug Detect 5 T.M.D.S. Data4+ 17 T.M.D.S. Data0– 6 DDC Clock 18 T.M.D.S. Data0+ 7 DDC Data 19 T.M.D.S. Data0/5 Shield 8 No Connect 20 T.M.D.S. Data5– 9 T.M.D.S. Data1– 21 T.M.D.S. Data5+ 10 T.M.D.S. Data1+ 22 T.M.D.S. Data Shield 11 T.M.D.S. Data1/3 Shield 23 T.M.D.S.
DisplayPort Connector Connector and Icon Pin Signal Pin Signal 1 ML_Lane 0 (p) 13 CONFIG1 2 Ground 14 CONFIG2 3 ML_Lane 0 (n) 15 AUX CH (p) 4 ML_Lane 1 (p) 16 Ground 5 Ground 17 AUX CH (n) 6 ML_Lane 1 (n) 18 Hot Plug 7 ML_Lane 2 (p) 19 Return 8 Ground 20 DP_PWR 9 ML_Lane 2 (n) 10 ML_Lane 3 (p) 11 Ground 12 ML_Lane 3 (n) 182 Appendix A Connector Pin Assignments
B Power Cord Set Requirements The power supplies on some computers have external power switches. The voltage select switch feature on the computer permits it to operate from any line voltage between 100-120 or 220-240 volts AC. Power supplies on those computers that do not have external power switches are equipped with internal switches that sense the incoming voltage and automatically switch to the proper voltage.
Country-Specific Requirements Additional requirements specific to a country are shown in parentheses and explained below. Country Accrediting Agency Country Accrediting Agency Australia (1) EANSW Italy (1) IMQ Austria (1) OVE Japan (3) METI Belgium (1) CEBC Norway (1) NEMKO Canada (2) CSA Sweden (1) SEMKO Denmark (1) DEMKO Switzerland (1) SEV Finland (1) SETI United Kingdom (1) BSI France (1) UTE United States (2) UL Germany (1) VDE 1.
C POST Error Messages This appendix lists the error codes, error messages, and the various indicator light and audible sequences that you may encounter during Power-On Self-Test (POST) or computer restart, the probable source of the problem, and steps you can take to resolve the error condition. POST Message Disabled suppresses most system messages during POST, such as memory count and non-error text messages. If a POST error occurs, the screen will display the error message.
POST Numeric Codes and Text Messages This section covers those POST errors that have numeric codes associated with them. The section also includes some text messages that may be encountered during POST. NOTE: The computer will beep once after a POST text message is displayed on the screen. Table C-1 Numeric Codes and Text Messages Control panel message Description Recommended action 101-Option ROM Checksum Error System ROM or expansion board option ROM checksum. 1. Verify the correct ROM. 2.
Table C-1 Numeric Codes and Text Messages (continued) Control panel message Description Recommended action 163-Time & Date Not Set Invalid time or date in configuration memory. Reset the date and time under Control Panel (Computer Setup can also be used). If the problem persists, replace the RTC battery. See the Hardware Reference Guide for instructions on installing a new battery, or contact an authorized dealer or reseller for RTC battery replacement.
Table C-1 Numeric Codes and Text Messages (continued) Control panel message Description Recommended action 301-Keyboard Error Keyboard failure. 1. Reconnect keyboard with computer turned off. 2. Check connector for bent or missing pins. 3. Ensure that none of the keys are depressed. 4. Replace keyboard. 1. Reconnect keyboard with computer turned off. 2. Replace the system board. 1. Reconnect the keyboard with computer turned off. 2. Ensure that none of the keys are depressed. 3.
Table C-1 Numeric Codes and Text Messages (continued) Control panel message Description Recommended action 605-Diskette Drive Type Error Mismatch in drive type. 1. Disconnect any other diskette controller devices (tape drives). 2. Clear CMOS. (See Appendix B, Password Security and Resetting CMOS on page 235.) 660-Display cache is detected unreliable Integrated graphics controller display cache is not working properly and will be disabled.
Table C-1 Numeric Codes and Text Messages (continued) Control panel message Description Recommended action 1720-SMART Hard Drive Detects Imminent Failure Hard drive is about to fail. (Some hard drives have a hard drive firmware patch that will fix an erroneous error message.) 1. Determine if hard drive is giving correct error message. Enter Computer Setup and run the Drive Protection System test under Storage > DPS Self-test. 2. Apply hard drive firmware patch if applicable.
Table C-1 Numeric Codes and Text Messages (continued) Control panel message Description Recommended action 2202-PMM Deallocation Error during MEBx cleanup Memory error during POST execution of the Management Engine (ME) BIOS Extensions option ROM. 1. Reboot the computer. 2. Unplug the power cord, re-seat the memory modules, and reboot the computer. 3. If the memory configuration was recently changed, unplug the power cord, restore the original memory configuration, and reboot the computer. 4.
Table C-1 Numeric Codes and Text Messages (continued) Control panel message Description Recommended action Network Server Mode Active and No Keyboard Attached Keyboard failure while Network Server Mode enabled. 1. Reconnect keyboard with computer turned off. 2. Check connector for bent or missing pins. 3. Ensure that none of the keys are depressed. 4. Replace keyboard. Parity Check 2 Parity RAM failure. Run Computer Setup and Diagnostic utilities.
Interpreting POST Diagnostic Front Panel LEDs and Audible Codes This section covers the front panel LED codes as well as the audible codes that may occur before or during POST that do not necessarily have an error code or text message associated with them. WARNING! When the computer is plugged into an AC power source, voltage is always applied to the system board.
Table C-2 Diagnostic Front Panel LEDs and Audible Codes (continued) Activity Beeps Possible Cause Recommended Action Red Power LED flashes four times, once every second, followed by a two second pause. Beeps stop after fifth iteration but LEDs continue until problem is solved. 4 Power failure (power supply is overloaded). 1. Open the hood and ensure the 4 or 6-wire power supply cable is seated into the connector on the system board. 2.
Table C-2 Diagnostic Front Panel LEDs and Audible Codes (continued) Activity Beeps Possible Cause Recommended Action Red Power LED flashes nine times, once every second, followed by a two second pause. Beeps stop after fifth iteration but LEDs continue until problem is solved. 9 System powers on but is unable to boot. 1. Check that the voltage selector, located on the rear of the power supply (some models), is set to the appropriate voltage. Proper voltage setting depends on your region. 2.
Table C-2 Diagnostic Front Panel LEDs and Audible Codes (continued) Activity Beeps Possible Cause Recommended Action Red Power LED flashes eleven times, once every second, followed by a two second pause. Beeps stop after fifth iteration but LEDs continue until problem is solved. 11 The current processor does not support a feature previously enabled on this system. 1. Install a TXT capable processor. 2. Disable TXT in the Computer Setup (F10) utility. 3. Reinstall the original processor.
D Troubleshooting Without Diagnostics This chapter provides information on how to identify and correct minor problems, such as hard drive, optical drive, graphics, audio, memory, and software problems. If you encounter problems with the computer, refer to the tables in this chapter for probable causes and recommended solutions. NOTE: For information on specific error messages that may appear on the screen during Power-On Self-Test (POST) at startup, refer to Appendix A, POST Error Messageson page 185.
● Refer to the comprehensive online technical support at http://www.hp.com/support. ● Refer to Helpful Hints on page 198 in this guide. To assist you in resolving problems online, HP Instant Support Professional Edition provides you with self-solve diagnostics. If you need to contact HP support, use HP Instant Support Professional Edition's online chat feature. Access HP Instant Support Professional Edition at: http://www.hp.com/go/ispe. Access the Business Support Center (BSC) at http://www.hp.
● Reconfigure the computer after installing a non-plug and play expansion board or other option. See Solving Hardware Installation Problems on page 219 for instructions. ● Be sure that all the needed device drivers have been installed. For example, if you are using a printer, you need a driver for that model printer. ● Remove all bootable media (CD or USB device) from the system before turning it on.
Solving General Problems You may be able to easily resolve the general problems described in this section. If a problem persists and you are unable to resolve it yourself or if you feel uncomfortable about performing the operation, contact an authorized dealer or reseller. WARNING! When the computer is plugged into an AC power source, voltage is always applied to the system board.
Table D-1 Solving General Problems (continued) There is no sound or sound volume is too low. Cause Solution System volume may be set low or muted. 1. Check the F10 BIOS settings to make sure the internal system speaker is not muted (this setting does not affect the external speakers). 2. Make sure the external speakers are properly connected and powered on and that the speakers' volume control is set correctly. 3.
Table D-1 Solving General Problems (continued) Poor performance is experienced. Cause Solution Too many applications running. 1. Close unnecessary applications to free up memory. 2. Add more memory. Some applications run in the background and can be closed by right-clicking on their corresponding icons in the task tray. To prevent these applications from launching at startup, go to Start > Run (Windows XP) or Start > Accessories > Run (Windows Vista) and type msconfig.
Table D-1 Solving General Problems (continued) System does not power on and the LEDs on the front of the computer are not flashing. Cause Solution System unable to power on. Press and hold the power button for less than 4 seconds. If the hard drive LED turns green, then: 1. Remove the expansion cards one at a time until the 5V_aux light on the system board turns on. 2. Replace the system board. OR Press and hold the power button for less than 4 seconds.
Solving Power Problems Common causes and solutions for power problems are listed in the following table. Table D-2 Solving Power Problems Power supply shuts down intermittently. Cause Solution Power supply will not turn on because of internal power supply fault. Contact an authorized service provider to replace the power supply. Computer powered off automatically and the Power LED flashes Red two times, once every second, followed by a two second pause, and the computer beeps two times.
Solving Hard Drive Problems Table D-3 Solving Hard Drive Problems Hard drive error occurs. Cause Solution Hard disk has bad sectors or has failed. 1. In Microsoft Windows XP, right-click Start, click Explore, and select a drive. Select File > Properties > Tools. Under Error-checking, click Check Now. In Microsoft Windows Vista, right-click Start, click Explore, and right-click on a drive. Select Properties then select the Tools tab. Under Errorchecking click Check Now. 2.
Table D-3 Solving Hard Drive Problems (continued) Nonsystem disk/NTLDR missing message. Cause Solution The system is trying to start from a media device that is not bootable. Remove the media device from the drive. The system is trying to start from the hard drive but the hard drive may have been damaged. 1. Insert a bootable media device into the drive and restart the computer. 2. Check the hard drive format using fdisk: If NTFS formatting, use a third party reader to evaluate the drive.
Table D-3 Solving Hard Drive Problems (continued) Computer seems to be locked up. Cause Solution Program in use has stopped responding to commands. Attempt the normal Windows “Shut Down” procedure. If this fails, press the power button for four or more seconds to turn off the power. To restart the computer, press the power button again. The removable hard drive has no power to the hard drive enclosure. Cause Solution The lock on the enclosure is not turned to the “ON” position.
Solving Media Card Reader Problems Table D-4 Solving Media Card Reader Problems Media card will not work in a digital camera after formatting it in Microsoft Windows XP or Microsoft Windows Vista. Cause Solution By default, Windows XP and Windows Vista will format any media card with a capacity greater than 32MB with the FAT32 format. Most digital cameras use the FAT (FAT16 & FAT12) format and can not operate with a FAT32 formatted card.
Table D-4 Solving Media Card Reader Problems (continued) After installing the media card reader and booting to Windows, the reader and the inserted cards are not recognized by the computer. Cause Solution The operating system needs time to recognize the device if the reader was just installed into the computer and you are turning the PC on for the first time.
Solving Display Problems If you encounter display problems, see the documentation that came with the monitor and to the common causes and solutions listed in the following table. Table D-5 Solving Display Problems Blank screen (no video). Cause Solution Monitor is not turned on and the monitor light is not on. Turn on the monitor and check that the monitor light is on. Bad monitor. Try a different monitor. The cable connections are not correct.
Table D-5 Solving Display Problems (continued) Cannot enable integrated graphics after installing a PCI Express graphics card. Cause Solution On systems with Intel integrated graphics, the integrated graphics cannot be enabled after installing a PCI Express x16. The integrated graphics can be enabled in Computer Setup if a PCI or PCI Express x1 graphics card is installed, but it cannot be enabled if there is a graphics card in the PCI Express x16 slot.
Table D-5 Solving Display Problems (continued) Dim characters. Cause Solution The brightness and contrast controls are not set properly. Adjust the monitor brightness and contrast controls. Cables are not properly connected. Check that the graphics cable is securely connected to the graphics card and the monitor. Blurry video or requested resolution cannot be set. Cause Solution If the graphics controller was upgraded, the correct graphics drivers may not be loaded.
Table D-5 Solving Display Problems (continued) “Out of Range” displays on screen. Cause Solution Video resolution and refresh rate are set higher than what the monitor supports. Restart the computer and enter Safe Mode. Change the settings to a supported setting then restart the computer so that the new settings take effect. Vibrating or rattling noise coming from inside a CRT monitor when powered on. Cause Solution Monitor degaussing coil has been activated. None.
Table D-5 Solving Display Problems (continued) Certain typed symbols do not appear correct. Cause Solution The font you are using does not support that particular symbol. Use the Character Map to locate and select the appropriate symbol. Click Start > All Programs > Accessories > System Tools > Character Map. You can copy the symbol from the Character Map into a document.
Table D-6 Solving Audio Problems (continued) Sound does not come out of the speaker or headphones. Cause Solution External speakers plugged into the wrong audio jack on a recently installed sound card. See the sound card documentation for proper speaker connection. Digital CD audio is not enabled. Enable digital CD audio. In the Device Manager, right-click on the CD/DVD device and select Properties. Make sure Enable digital CD audio for this CD-ROM device is checked.
Solving Printer Problems If you encounter printer problems, see the documentation that came with the printer and to the common causes and solutions listed in the following table. Table D-7 Solving Printer Problems Printer will not print. Cause Solution Printer is not turned on and online. Turn the printer on and make sure it is online. The correct printer drivers for the application are not installed. 1. Install the correct printer driver for the application. 2.
Solving Keyboard and Mouse Problems If you encounter keyboard or mouse problems, see the documentation that came with the equipment and to the common causes and solutions listed in the following table. Table D-8 Solving Keyboard Problems Keyboard commands and typing are not recognized by the computer. Cause Solution Keyboard connector is not properly connected. 1. On the Windows XP Desktop, click Start > Shut Down.
Table D-9 Solving Mouse Problems (continued) Mouse does not respond to movement or is too slow. Cause Solution Mouse may need cleaning. Remove the roller ball cover on the mouse and clean the internal components. Mouse may need repair. See the Worldwide Limited Warranty for terms and conditions. Computer is in standby mode. Press the power button to resume from standby mode. CAUTION: When attempting to resume from standby mode, do not hold down the power button for more than four seconds.
Solving Hardware Installation Problems You may need to reconfigure the computer when you add or remove hardware, such as an additional drive or expansion card. If you install a plug and play device, Windows automatically recognizes the device and configures the computer. If you install a non–plug and play device, you must reconfigure the computer after completing installation of the new hardware. In Windows, use the Add Hardware Wizard and follow the instructions that appear on the screen.
Table D-10 Solving Hardware Installation Problems (continued) Power LED flashes Red five times, once every second, followed by a two second pause, and the computer beeps five times. (Beeps stop after fifth iteration but LEDs continue flashing.) Cause Solution Memory is installed incorrectly or is bad. CAUTION: To avoid damage to the DIMMs or the system board, you must unplug the computer power cord before attempting to reseat, install, or remove a DIMM module. 1. Reseat DIMMs. Power on the system. 2.
Solving Network Problems Some common causes and solutions for network problems are listed in the following table. These guidelines do not discuss the process of debugging the network cabling. Table D-11 Solving Network Problems Wake-on-LAN feature is not functioning. Cause Solution Wake-on-LAN is not enabled. To enable Wake-on-LAN in Windows XP: 1. Select Start > Control Panel. 2. Double-click Network Connections. 3. Double-click Local Area Connection. 4. Click Properties. 5. Click Configure.
Table D-11 Solving Network Problems (continued) Network status link light never flashes. NOTE: The network status light is supposed to flash when there is network activity. Cause Solution No active network is detected. Check cabling and network equipment for proper connection. Network controller is not set up properly. Check for the device status within Windows, such as Device Manager for driver load and the Network Connections applet within Windows for link status. Network controller is disabled. 1.
Table D-11 Solving Network Problems (continued) Network controller stopped working when an expansion board was added to the computer. Cause Solution The network controller requires drivers. Verify that the drivers were not accidentally deleted when the drivers for a new expansion board were installed. The expansion board installed is a network card (NIC) and conflicts with the embedded NIC. Under the Computer Setup Advanced menu, change the resource settings for the board.
Solving Memory Problems If you encounter memory problems, some common causes and solutions are listed in the following table. CAUTION: Power may still be supplied to the DIMMs when the computer is turned off (depending on the Management Engine (ME) settings on some models). To avoid damage to the DIMMs or the system board, you must unplug the computer power cord before attempting to reseat, install, or remove a DIMM module.
Table D-12 Solving Memory Problems (continued) Insufficient memory error during operation. Cause Solution Too many Terminate and Stay Resident programs (TSRs) are installed. Delete any TSRs that you do not need. You have run out of memory for the application. Check the memory requirements for the application or add more memory to the computer. Power LED flashes Red five times, once every second, followed by a two second pause, and the computer beeps five times.
Solving Processor Problems If you encounter processor problems, common causes and solutions are listed in the following table. Table D-13 Solving Processor Problems Poor performance is experienced. Cause Solution Processor is hot. 1. Make sure the airflow to the computer is not blocked. 2. Make sure the fans are connected and working properly (some fans only operate when needed). 3. Make sure the processor heat sink is installed properly.
Solving CD-ROM and DVD Problems If you encounter CD-ROM or DVD problems, see the common causes and solutions listed in the following table or to the documentation that came with the optional device. Table D-14 Solving CD-ROM and DVD Problems System will not boot from CD-ROM or DVD drive. Cause Solution The device is attached to a SATA port that has been hidden in the Computer Setup utility.
Table D-14 Solving CD-ROM and DVD Problems (continued) Movie will not play in the DVD drive. Cause Solution Movie may be regionalized for a different country. See the documentation that came with the DVD drive. Decoder software is not installed. Install decoder software. Damaged media. Replace media. Movie rating locked out by parental lock. Use DVD software to remove parental lock. Media installed upside down. Reinstall media. Cannot eject compact disc (tray-load unit).
Solving USB Flash Drive Problems If you encounter USB flash drive problems, common causes and solutions are listed in the following table. Table D-15 Solving USB Flash Drive Problems USB flash drive is not seen as a drive letter in Windows. Cause Solution The drive letter after the last physical drive is not available. Change the default drive letter for the flash drive in Windows. USB flash drive not found (identified).
Solving Front Panel Component Problems If you encounter problems with devices connected to the front panel, refer to the common causes and solutions listed in the following table. Table D-16 Solving Front Panel Component Problems A USB device, headphone, or microphone is not recognized by the computer. Cause Solution Device is not properly connected. 1. Turn off the computer. 2. Reconnect the device to the front of the computer and restart the computer. The device does not have power.
Solving Internet Access Problems If you encounter Internet access problems, consult your Internet Service Provider (ISP) or refer to the common causes and solutions listed in the following table. Table D-17 Solving Internet Access Problems Unable to connect to the Internet. Cause Solution Internet Service Provider (ISP) account is not set up properly. Verify Internet settings or contact your ISP for assistance. Modem is not set up properly. Reconnect the modem.
Table D-17 Solving Internet Access Problems (continued) Internet takes too long to download Web sites. Cause Solution Modem is not set up properly. Verify that the modem is connected and communicating properly. Windows XP 1. Select Start > Control Panel. 2. Double-click System. 3. Click the Hardware tab. 4. In the Device Manager area, click the Device Manager button. 5. Double-click Modems. 6. Double-click Agere Systems PCI-SV92PP Soft Modem. 7. On the General tab, click Diagnostics. 8.
Solving Software Problems Most software problems occur as a result of the following: ● The application was not installed or configured correctly. ● There is insufficient memory available to run the application. ● There is a conflict between applications. ● Be sure that all the needed device drivers have been installed. ● If you have installed an operating system other than the factory-installed operating system, check to be sure it is supported on the system.
Contacting Customer Support For help and service, contact an authorized reseller or dealer. To locate a reseller or dealer near you, visit http://www.hp.com. NOTE: If you take the computer to an authorized reseller, dealer, or service provider for service, remember to provide the setup and power-on passwords if they are set. Refer to the number listed in the warranty or in the Support Telephone Numbers guide for technical assistance.
E Password Security and Resetting CMOS This computer supports security password features, which can be established through the Computer Setup Utilities menu. This computer supports two security password features that are established through the Computer Setup Utilities menu: setup password and power-on password. When you establish only a setup password, any user can access all the information on the computer except Computer Setup.
Resetting the Password Jumper To disable the power-on or setup password features, or to clear the power-on or setup passwords, complete the following steps: 1. Shut down the operating system properly, then turn off the computer and any external devices, and disconnect the power cord from the power outlet. 2. With the power cord disconnected, press the power button again to drain the system of any residual power.
Clearing and Resetting the CMOS The computer’s configuration memory (CMOS) stores information about the computer’s configuration. The CMOS button resets CMOS but does not clear the power-on and setup passwords. Clearing CMOS will clear the Active Management Technology (AMT) settings in the Management Engine BIOS Extension (MEBx), including the password. The password will default to “admin” and will need to be reset. The AMT settings will also need to be reset. To access the MEBx, press Ctrl+P during POST.
4. Locate, press, and hold the CMOS button in for five seconds. NOTE: Make sure you have disconnected the AC power cord from the wall outlet. The CMOS button will not clear CMOS if the power cord is connected. Figure E-1 CMOS button NOTE: For assistance locating the CMOS button and other system board components, see the Illustrated Parts & Service Map (IPSM) for that particular system. 5. Replace the computer cover or access panel. 6. Reconnect the external devices. 7.
F Specifications This chapter provides specifications for the microtower and small form factor chassis. Microtower Chassis Table F-1 Specifications Desktop Dimensions Height 14.85 in 37.72 cm Width 6.95 in 17.65 cm Depth 16.85 in 42.80 cm Approximate Weight 23.5 lb 10.66 kg Operating 50° to 95°F 10° to 35°C Nonoperating -22° to 140°F -30° to 60°C Operating 10-90% 10-90% Nonoperating (38.
Table F-1 Specifications (continued) Power Supply 115V 230V Operating Voltage Range (STD PS) 90-264 VAC 90-264 VAC Operating Voltage Range (EPA 87/89/85% @ 20/50/100% load PS) 90-264 VAC 90-264 VAC Rated Voltage Range (STD PS) 100-240 VAC 100-240 VAC Rated Voltage Range (EPA 87/89/85% @ 20/50/100% load PS) 100-240 VAC 100-240 VAC Rated Line Frequency 50-60 Hz 50-60 Hz Power Output 320W 320W STD PS 5.5A @ 115 VAC 2.75A @ 230 VAC EPA 87/89/85% @ 20/50/100% load PS 5.5A @ 115 VAC 2.
Small Form Factor Chassis Table F-2 Specifications Desktop Dimensions (in the desktop position) Height 3.95 in 10.0 cm Width 13.3 in 33.8 cm Depth 14.9 in 37.8 cm Approximate Weight 19 lb 8.6 kg Weight Supported (maximum distributed load in desktop position) 77 lb 35 kg Operating 50° to 95°F 10° to 35°C Nonoperating -22° to 140°F -30° to 60°C Temperature Range NOTE: Operating temperature is derated 1.
Table F-2 Specifications (continued) Rated Input Current (maximum)1 1 STD PS 4A @ 100 VAC 2A @ 230 VAC EPA 87/89/85% @ 20/50/100% load PS 4A @ 100 VAC 2A @ 230 VAC This system utilizes an active power factor corrected power supply. This allows the system to pass the CE mark requirements for use in the countries of the European Union. The active power factor corrected power supply also has the added benefit of not requiring an input voltage range select switch.
Index Symbols/Numerics 4–pin power pin assignments 177 A access panel, locked 201 access to computer, controlling 50 Altiris Client Management Suite 39 asset tracking 50 audible codes 193 audio connectors 2, 4, 7, 9 audio problems 214 B battery disposal 72 SFF removal and replacement 165 beep codes 193 BIOS Boot Block Emergency Recovery Mode 44 HPQFlash 43 Remote ROM Flash 35 Boot Block Emergency Recovery Mode 44 bootable device creating 46 USB flash media device 46 booting options Full Boot 185 Quick Boot
E electrostatic discharge (ESD) preventing damage 67 Emergency Recovery Mode, Boot Block 44 entering power-on password 55 setup password 55 error codes 185, 193 messages 186 ethernet RJ-45 pin assignments 175 expansion card installing 128 removing 128 slot locations 128 expansion slot cover removing 84, 129 replacing 86, 131 F FailSafe Key, ordering 59 fan shroud SFF removal and replacement 155 fan, power supply 71 fan/air baffle MT removal and replacement 104 Fault Notification and Recovery 60 fingerprint
MT removal and replacement 80 populating sockets 82 memory problems 224 microphone connector 2, 7 microphone pin assignments 176 monitor pin assignments 177 monitor connector DisplayPort 4, 9 VGA 4, 9 monitor problems 210 mouse pin assignments 174 mouse cleaning 71 mouse connector 4, 9 mouse problems 217 MT access panel removal and replacement 75 cable management 78 chassis, illustrated 66 disassembly preparation 74 external security 116 fan/air baffle removal and replacement 104 front bezel removal and rep
Recovery Mode, Boot Block Emergency 44 recovery, software 33 Remote Management Technology 40 Remote ROM Flash 35 remote setup 35 Remote System Installation 35 removable hard drive replacing 99, 151 removal and replacement MT access panel 75 MT fan/air baffle 104 MT front bezel 76 MT front USB panel 105 MT heat sink 107 MT memory 80 MT power supply 111 MT power switch/LED assembly 106 MT processor 108 MT rear chassis fan 110 MT speaker 109 MT system board 112 SFF baffle 155 SFF battery 165 SFF front fan 156
HP System Software Manager 36 integration 33 Proactive Change Notification (PCN) 42 problems 233 recovery 33 Remote Management Technology 40 Remote System Installation 35 servicing computer 71 updating and management tools 35 Verdiem Surveyor 42 spare part number tamper-resistent wrench 71 Torx T-15 screwdriver 71 speaker MT removal and replacement 109 SFF removal and replacement 159 specifications computer 239, 241 MT memory 80 static electricity 66 Subscriber's Choice 42 surge-tolerant power supply 60 sys
