user manual
Table Of Contents
- NC8100H.pdf
- Introduction
- TABLE OF CONTENTS
- IMPORTANT INFORMATION: REGULATIONS
- CHAPTER ONE TCP/IP CONFIGURATION ASSIGNING TCP/IP INFORMATION
- Overview
- Using the MFC front panel to allocate an IP address.
- Using BRAdmin and the TCP/IP Protocol to set the IP address
- Using BRAdmin and the IPX/SPX Protocol to set the IP address
- Changing the IP Address using the BRAdmin application
- Using DHCP to Configure the IP address
- Using ARP to Configure the Print / Fax server IP Address
- Using RARP to Configure the IP Address
- Using BOOTP to Configure the IP Address
- Changing the IP Address settings with the TELNET Console
- Other Sources of Information
- CHAPTER TWO FRONT PANEL SETUP MENU
- CHAPTER THREE WEB BASED MANAGEMENT HOW TO USE THE WEB-BASED MANAGEMENT UTILITY
- CHAPTER FOUR INTERNET FAX
- Overview
- Sending an Internet Fax
- Using Scan to E-mail
- Receiving E-mail or Internet Fax
- Receiving an Internet Fax to a PC
- Forwarding Received E-mail and Fax Messages
- Relay Broadcasting
- TX Verification Mail
- Setup Mail (TX)
- Setup Mail (RX)
- Error mail
- Important information on Internet Fax
- Other Sources of Information
- CHAPTER FIVE TCP/IP PRINTING PRINTING FROM WINDOWS® NT® OR WINDOWS® 2000, LAN SERVER AND WARP SERVER
- Overview
- Windows® NT® 3.5x/NT® 4.0/2000 (TCP/IP) Configuration
- Windows® 2000 Printing (Printer Driver not yet installed)
- IPP Printing from Windows® 2000 Clients
- Windows® 2000 Printing (Printer Driver already installed)
- Windows® NT® 4.0 Printing
- Windows® NT® 4.0 Printing (Printer Driver not yet installed)
- Windows® NT®4.0 Printing (Printer Driver already installed)
- Windows® NT® 3.5x Printing
- Windows® NT® 3.5x Printing (Printer Driver not yet installed)
- Other Sources of Information
- CHAPTER SIX PEER TO PEER PRINTING HOW TO PRINT IN A WINDOWS® 95/98/ME PEER TO PEER NETWORK
- CHAPTER SEVEN NETBIOS PEER TO PEER PRINTING HOW TO PRINTING USING NETBIOS ON WINDOWS® 95/98/ME/NT®/2000
- CHAPTER EIGHT HOW TO CONFIGURE INTERNET PRINTING FOR WINDOWS® 95/98/ME/NT®4.0/2000 INTERNET PRINTING INSTALLATION
- Overview
- Brother Internet Print General Information
- Brother Internet Print Configuring the Brother Print / Fax server
- Brother Internet Print Using BRAdmin to Configure the Print / Fax server
- Brother Internet Print Using a Web Browser to configure the Print / Fax server
- Brother Internet Print Using TELNET to Configure the Print / Fax server
- Brother Internet Print Installing the BIP software on Windows® 95/98/Me/NT®4.0/2000
- Adding a Second Brother Internet Port
- Windows® 2000 IPP Printing
- Specifying a different URL
- Other Sources of Information
- CHAPTER NINE NOVELL NETWARE PRINTING HOW TO CONFIGURE NOVELL NETWARE PRINTING
- Overview
- General Information
- Creating a NDPS Printer Using NWADMIN for NetWare5
- NDPS Manager
- NDPS Broker
- Creating a Printer Agent
- Configuring Netware 3 and NetWare 4 systems
- Configuring the Brother Print / Fax server (Queue Server Mode in Bindery emulation mode) using BRAdmin
- Configuring the Brother Print / Fax server (Queue Server Mode in NDS mode) using BRAdmin
- Configuring the Brother Print / Fax server (Queue Server Mode in NDS mode) using Novell NWADMIN and BRAdmin
- Configuring the Brother Print / Fax server (Remote Server Mode in NDS mode) using Novell NWAdmin and BRAdmin
- Configuring the Brother Print / Fax server (Queue Server Mode in Bindery emulation mode) using PCONSOLE and BRCONFIG
- Configuring the Brother Print / Fax server (Queue Server Mode in NDS mode) using PCONSOLE and BRCONFIG
- Configuring the Brother Print / Fax server (Remote Printer Mode using PCONSOLE and BRCONFIG
- Other Sources of Information
- CHAPTER TEN PRINTING FROM A MACINTOSH®
- CHAPTER ELEVEN DLC PRINTING PRINTING FROM WINDOWS® NT® OR WINDOWS® 2000
- CHAPTER TWELVE UNIX PRINTING PRINTING FROM UNIX/LINUX USING TCP/IP
- CHAPTER THIRTEEN TROUBLESHOOTING
- Overview
- Installation problems
- Intermittent Problems
- TCP/IP Troubleshooting
- UNIX Troubleshooting
- Windows® NT®/LAN Server (TCP/IP) Troubleshooting
- Windows® 95/98/Me Peer to Peer Print (LPR) Troubleshooting
- Windows® 95/98/Me Peer-to-Peer (HP JetAdmin compatible method) Troubleshooting
- Windows® 95/98/Me/NT®4.0 Peer-to-Peer Print (NetBIOS) Troubleshooting
- Brother Internet Print (TCP/IP) Troubleshooting
- Windows® 95/98/Me/2000 FTP/IPP Troubleshooting
- Novell NetWare Troubleshooting
- AppleTalk Troubleshooting
- DLC/LLC Troubleshooting
- Web Browser Troubleshooting (TCP/IP)
- Internet Fax Troubleshooting
- CHAPTER FOURTEEN BROTHER NETWORK PC FAX SOFTWARE INSTALLING AND USING THE BROTHER NETWORK PC FAX SOFTWARE
- Overview
- Installing Network PC Fax
- Setting Up User Information
- Setting Up Sending Information
- Setting Up Speed Dial
- The Address Book
- Setting Up a Group for Broadcasting
- Sending a File as a PC FAX Using the Simple Style
- Sending a File as a PC FAX using the Facsimile Style
- Updating other MFC’s through the Network.
- Other Sources of Information
- APPENDIX
- INDEX

CHAPTER 1 TCP/IP CONFIGURATION
1-1
1
11
CHAPTER ONE
11
TCP/IP Configuration
11
Assigning TCP/IP Information
Overview
The TCP/IP protocol requires that each device on the network have it's own
unique IP address. Use the following information to learn about IP address
configuration.
By default Brother Print / Fax servers have a sample IP address of 192.0.0.192,
however, you can easily change this IP address number to match with the IP
address details of your network. This can be done in any of the following ways:
1. MFC front panel setting.
2. BRAdmin application (for Windows
®
95/98/Me/NT
®
4.0/2000 using the
IPX/SPX or TCP/IP protocol).
3. DHCP, Reverse ARP (rarp) or BOOTP.
4. The ARP command.
5. Brother BRCONFIG NetWare utility (A Novell Network is necessary).
Other ways to CHANGE the IP address once it is already set:
1. MFC front panel
2. TELNET
3. HTTP (Web browser)
4. Other SNMP based management utility
These configuration methods are described in the following paragraphs.
The IP address you assign to the Print / Fax server must be on the same logical
network as your host computers, if it is not, you must properly configure the
subnet mask and the router (gateway).