user manual
Table Of Contents
- NC8100H.pdf
- Introduction
- TABLE OF CONTENTS
- IMPORTANT INFORMATION: REGULATIONS
- CHAPTER ONE TCP/IP CONFIGURATION ASSIGNING TCP/IP INFORMATION
- Overview
- Using the MFC front panel to allocate an IP address.
- Using BRAdmin and the TCP/IP Protocol to set the IP address
- Using BRAdmin and the IPX/SPX Protocol to set the IP address
- Changing the IP Address using the BRAdmin application
- Using DHCP to Configure the IP address
- Using ARP to Configure the Print / Fax server IP Address
- Using RARP to Configure the IP Address
- Using BOOTP to Configure the IP Address
- Changing the IP Address settings with the TELNET Console
- Other Sources of Information
- CHAPTER TWO FRONT PANEL SETUP MENU
- CHAPTER THREE WEB BASED MANAGEMENT HOW TO USE THE WEB-BASED MANAGEMENT UTILITY
- CHAPTER FOUR INTERNET FAX
- Overview
- Sending an Internet Fax
- Using Scan to E-mail
- Receiving E-mail or Internet Fax
- Receiving an Internet Fax to a PC
- Forwarding Received E-mail and Fax Messages
- Relay Broadcasting
- TX Verification Mail
- Setup Mail (TX)
- Setup Mail (RX)
- Error mail
- Important information on Internet Fax
- Other Sources of Information
- CHAPTER FIVE TCP/IP PRINTING PRINTING FROM WINDOWS® NT® OR WINDOWS® 2000, LAN SERVER AND WARP SERVER
- Overview
- Windows® NT® 3.5x/NT® 4.0/2000 (TCP/IP) Configuration
- Windows® 2000 Printing (Printer Driver not yet installed)
- IPP Printing from Windows® 2000 Clients
- Windows® 2000 Printing (Printer Driver already installed)
- Windows® NT® 4.0 Printing
- Windows® NT® 4.0 Printing (Printer Driver not yet installed)
- Windows® NT®4.0 Printing (Printer Driver already installed)
- Windows® NT® 3.5x Printing
- Windows® NT® 3.5x Printing (Printer Driver not yet installed)
- Other Sources of Information
- CHAPTER SIX PEER TO PEER PRINTING HOW TO PRINT IN A WINDOWS® 95/98/ME PEER TO PEER NETWORK
- CHAPTER SEVEN NETBIOS PEER TO PEER PRINTING HOW TO PRINTING USING NETBIOS ON WINDOWS® 95/98/ME/NT®/2000
- CHAPTER EIGHT HOW TO CONFIGURE INTERNET PRINTING FOR WINDOWS® 95/98/ME/NT®4.0/2000 INTERNET PRINTING INSTALLATION
- Overview
- Brother Internet Print General Information
- Brother Internet Print Configuring the Brother Print / Fax server
- Brother Internet Print Using BRAdmin to Configure the Print / Fax server
- Brother Internet Print Using a Web Browser to configure the Print / Fax server
- Brother Internet Print Using TELNET to Configure the Print / Fax server
- Brother Internet Print Installing the BIP software on Windows® 95/98/Me/NT®4.0/2000
- Adding a Second Brother Internet Port
- Windows® 2000 IPP Printing
- Specifying a different URL
- Other Sources of Information
- CHAPTER NINE NOVELL NETWARE PRINTING HOW TO CONFIGURE NOVELL NETWARE PRINTING
- Overview
- General Information
- Creating a NDPS Printer Using NWADMIN for NetWare5
- NDPS Manager
- NDPS Broker
- Creating a Printer Agent
- Configuring Netware 3 and NetWare 4 systems
- Configuring the Brother Print / Fax server (Queue Server Mode in Bindery emulation mode) using BRAdmin
- Configuring the Brother Print / Fax server (Queue Server Mode in NDS mode) using BRAdmin
- Configuring the Brother Print / Fax server (Queue Server Mode in NDS mode) using Novell NWADMIN and BRAdmin
- Configuring the Brother Print / Fax server (Remote Server Mode in NDS mode) using Novell NWAdmin and BRAdmin
- Configuring the Brother Print / Fax server (Queue Server Mode in Bindery emulation mode) using PCONSOLE and BRCONFIG
- Configuring the Brother Print / Fax server (Queue Server Mode in NDS mode) using PCONSOLE and BRCONFIG
- Configuring the Brother Print / Fax server (Remote Printer Mode using PCONSOLE and BRCONFIG
- Other Sources of Information
- CHAPTER TEN PRINTING FROM A MACINTOSH®
- CHAPTER ELEVEN DLC PRINTING PRINTING FROM WINDOWS® NT® OR WINDOWS® 2000
- CHAPTER TWELVE UNIX PRINTING PRINTING FROM UNIX/LINUX USING TCP/IP
- CHAPTER THIRTEEN TROUBLESHOOTING
- Overview
- Installation problems
- Intermittent Problems
- TCP/IP Troubleshooting
- UNIX Troubleshooting
- Windows® NT®/LAN Server (TCP/IP) Troubleshooting
- Windows® 95/98/Me Peer to Peer Print (LPR) Troubleshooting
- Windows® 95/98/Me Peer-to-Peer (HP JetAdmin compatible method) Troubleshooting
- Windows® 95/98/Me/NT®4.0 Peer-to-Peer Print (NetBIOS) Troubleshooting
- Brother Internet Print (TCP/IP) Troubleshooting
- Windows® 95/98/Me/2000 FTP/IPP Troubleshooting
- Novell NetWare Troubleshooting
- AppleTalk Troubleshooting
- DLC/LLC Troubleshooting
- Web Browser Troubleshooting (TCP/IP)
- Internet Fax Troubleshooting
- CHAPTER FOURTEEN BROTHER NETWORK PC FAX SOFTWARE INSTALLING AND USING THE BROTHER NETWORK PC FAX SOFTWARE
- Overview
- Installing Network PC Fax
- Setting Up User Information
- Setting Up Sending Information
- Setting Up Speed Dial
- The Address Book
- Setting Up a Group for Broadcasting
- Sending a File as a PC FAX Using the Simple Style
- Sending a File as a PC FAX using the Facsimile Style
- Updating other MFC’s through the Network.
- Other Sources of Information
- APPENDIX
- INDEX
CHAPTER 1 TCP/IP CONFIGURATION
1-6
Using ARP to Configure the Print / Fax
server IP Address
If you are unable to use the BRAdmin application, MFC front panel and your
network does not use a DHCP server, you can also use the ARP command. ARP
is the simplest method of configuring the Print / Fax server IP address. The ARP
command is available on Windows
®
systems that have TCP/IP installed as well
as Unix systems. To use arp enter the following command the command prompt:
arp -s ipaddress ethernetaddress
Where ethernetaddress is the Ethernet address (MAC address) of the Print / Fax
server and ipaddress is the IP address of the Print / Fax server. For example:
Windows
®
Systems
Windows
®
Systems require the colon ":" character in-between each digit of the
Ethernet address.
arp -s 192.189.207.2 00:80:77:31:01:07
Unix Systems
Typically, Unix systems require the hash "-" character in-between each digit of
the Ethernet address.
arp -s 192.189.207.2 00-80-77-31-01-07
You must be on the same Ethernet segment (that is, there cannot be a router
between the Print / Fax server and operating system) to use the arp -s command.
If there is a router, you may use BOOTP or other methods described in this
chapter to enter the IP address.
If your Administrator has configured the system to deliver IP addresses using
BOOTP, DHCP or RARP your Brother Print / Fax server can receive an IP
address from any one of these IP address allocation systems, in which case, you
will not need to use the ARP command. The ARP command only works once.
For security reasons, once you have successfully configured the IP address of a
Brother Print / Fax server using the ARP command, you cannot use the ARP
command again to change the address. The Print / Fax server will ignore any
attempts to do this. If you wish to change the IP address again, use a Web
Browser, TELNET (using the SET IP ADDRESS command) the MFC’s front
panel or factory reset the Print / Fax server (which will then allow you to use the
ARP command again).
To configure the Print / Fax server and to verify the connection, enter the
following command ping ipaddress where the ipaddress is the IP address of the
Print / Fax server.
For example:
ping 192.189.207.2